Abstract:The present work is focused on the multidirectional forging (MDF) of Al–20 wt-% Si alloys with the addition of refiners and modifiers. The MDF process was performed at 200°C with a cumulative strain of 0.63. Microstructural characterization and mechanical performance were evaluated on the Al–20Si, Al–20Si–4.5Cu, Al–20Si–4.5Cu–1(Al–Ti–B), Al–20Si–4.5Cu–1(Al–Ti–B)–10(Al–Sr). The microstructure analysis revealed significant changes in the eutectic and primary phase refinement. The micro-Vickers hardness confirmed that the MDF process resulted in increased hardness (125 ± 1.9 VHN) compared to the homogenized samples (96 ± 2.7 VHN). Tensile test results showed that with the accumulation of strain, ultimate tensile strength increased to 435 MPa from 302 MPa with reduction in the percentage of elongation from 7.8 to 5.6. The grains were more uniformly distributed with addition of modifiers, and refiners further reduced the nucleation number of eutectic grains. The wear study demonstrated that the wear resistance is more in the Al–Si-Cu-Sr sample due to the increased level of hardness. The combination of multidirectional forging techniques with judicious incorporation of refiners and modifiers engenders a synergistic enhancement of microstructural integrity, hardness profiles, and wear-resistant properties in hypereutectic Al-20Si alloys. Le travail courant se concentre sur le forgeage multidirectionnel (MDF) des alliages Al-20% en poids Si avec ajout d'agents d'affinage et modificateurs. On a réalisé le procédé MDF à 200°C sur trois passes avec une déformation cumulée de 0.63. Suite au procédé MDF, on a évalué la caractérisation microstructurale et les performances mécaniques sur Al–20Si, Al–20Si–4.5Cu, Al–20Si–4.5Cu–1(Al–Ti–B) et Al–20Si–4.5Cu–1(Al–Ti–B)–10(Al–Sr). L'analyse de la microstructure a révélé des changements significatifs dans le raffinement de la phase eutectique et primaire après le traitement MDF. Les essais de microdureté Vickers ont confirmé que le procédé MDF entraînait une dureté accrue (125 ± 1.9 VHN) par rapport aux échantillons homogénéisés (96 ± 2.7 VHN). Les résultats des essais de traction ont montré qu'avec l'accumulation de déformation, la résistance ultime à la traction a augmenté de 302 MPa à 435 MPa avec une réduction du pourcentage d'allongement de 7.8 à 5.6. Les grains étaient distribués plus uniformément avec l'ajout d'agents modificateurs, et les agents d'affinage ont réduit davantage le nombre de nucléation des grains eutectiques. L'étude d'usure a démontré que la résistance à l'usure est supérieure dans l'échantillon Al–Si–Cu–Sr en raison du niveau de dureté accru. La combinaison des techniques de forgeage multidirectionnel avec l'incorporation judicieuse d'agents d'affinage et modificateurs engendre une amélioration synergique de l'intégrité microstructurale, des profils de dureté et des propriétés de résistance à l'usure des alliages hypereutectiques Al–20Si.

Combined effect of multidirectional forging and heat treatment on erosion and corrosion behaviour of the Mg-Zn-Mn alloys

Using Solution Heat Treatment and Multi Directional Forging to Improve the Mechanical and Corrosion Properties of an Mg–2Zn–0.2Ag Alloy

Achieving a high corrosion resistant and high strength magnesium alloy using multi directional forging

Microstructure, Texture, Mechanical Properties, and Corrosion Behavior of Biodegradable Zn-0.2Mg Alloy Processed by Multi-Directional Forging

Modulation of corrosion properties by heat treatment and extrusion with mechanism analysis of high mechanical strength Mg-5.6Dy-3.1Ni alloy

Simultaneously Enhanced Mechanical Properties and Damping Capacities of ZK60 Mg Alloys Processed by Multi-Directional Forging

Microstructure and Mechanical Properties of Al-Cu-Mn Alloy Mechanically Alloyed with 5 wt% Zr After Multi-Directional Forging

A Simple Surface Treatment for Mg to Gain Enhanced Resistance to Corrosion and Corrosive Wear by Hammering Al Powder‐Covered Mg Substrate

Effect of Multidirectional Forging and Aging Treatment on Wear Properties of ZK61 Alloy

Effect of Heat Treatment on Microstructure and Mechanical Properties of Mg-5Zn-1Mn Alloy Tube

Effect of multidirectional forging on grain structure and mechanical properties of hypereutectic Al–20%Si alloys with added refiners and modifiers

Effect of thermal treatment on the bio-corrosion and mechanical properties of ultrafine-grained ZK60 magnesium alloy

Effect Of Solution Treatment And Extrusion On The Microstructure And Mechanical Properties Of A Mg-2gd-Nd-0.4zn-0.3zr Alloy

Effects of heat treatment on mechanical properties of an extruded Mg-4.3Gd-3.2Y-1.2Zn-0.5Zr alloy and establishment of its Hall–Petch relation

Effect of Heat Treatment on Corrosion and Mechanical Properties of Mg-10Y-1.5Zn-0.5Zr Alloy

Microstructure Evolution and Mechanical Properties of AZ80 Mg Alloy during Annular Channel Angular Extrusion Process and Heat Treatment

Microstructural Evolution and Mechanical Properties of Extruded AZ80 Magnesium Alloy during Room Temperature Multidirectional Forging Based on Twin Deformation Mode

Significantly Improved Corrosion Resistance of Mg-15Gd-2Zn-0.39Zr Alloys: Effect of Heat-Treatment

Effect of Multidirectional Forging on the Microstructures and Mechanical Properties of the Al–Mg–Si Alloy

Effect of heat treatment on corrosion behaviors of Mg-6Gd-3Y-0.5Zr alloy

Heat Treatment-Induced Microstructure and Property Evolution of Mg/Al Intermetallic Compound Coatings Prepared by Al Electrodeposition on Mg Alloy from Molten Salt Electrolytes