Abstract:The ductility of sheet metal is typically limited by either localized necking or by damage and fracture. A recent ductility classification refers to these failure modes respectively as "global" and "local" formability. The forming limit curve (FLC) and the uniaxial tensile test assess global formability, whereas the fracture forming limit (FFL), the true thickness fracture strain, hole expansion ratios (HER), etc. are indicators of local formability. Experimental hole expansion data in the literature for different dual-phase (DP) steel grades of similar strength and composition presents a paradox: grades which are found to be ductile in a tensile test and/or FLC show a low ductility in hole expansion, whereas other grades with a low ductility in conventional tests perform surprisingly well at cut edges. In this work, an in-depth systematic statistical analysis of idealized artificial two-phase microstructures is carried out to unravel the underlying mechanisms of the observed paradoxical trends. This is done by scaling the hardness of martensite and its volume fraction to generate virtual DP steels of the same strength but different strain hardening and mechanical phase contrast (hardness difference). The proposed micromechanical model adequately reproduces the experimentally observed trends. The results show that in DP steels, a higher global (necking-driven) ductility is obtained upon delaying martensite plasticity by increasing the mechanical contrast of the two phases. Consequently, the stress–strain distributions becomes more heterogeneous, resulting in a lower fracture limit of one of the phases or interfaces in shear loading, thereby, reducing the local ductility. Global ductility is improved by higher mechanical phase contrast and lower martensite volume fraction, whereas local ductility is improved by low phase contrast and higher martensite volume fraction. The hardening behavior of martensite is the key to avoiding the above trade-off between local and global ductility. It is shown that if the strain hardening capacity of martensite in the later stages of deformation (in high strains) can be increased, this would result in removing the observed paradoxical trends of local and global ductility in DP steels.

On the interplay of friction and stress relaxation to improve stretch-flangeability of dual phase (DP600) steel

Does friction contribute to formability improvement using servo press?

Stretch flanging behaviour and microstructural analysis of DP steel using punch stretching and incremental forming processes

Strain-Hardening Behavior of Dual-Phase Steel under Multistress States

Enhancement of the stretch-flangeability of a cold-rolled dual phase steel intercritically annealed

Deformation Mechanics and Failure Mode in Stretch and Shrink Flanging by Double-Sided Incremental Forming

An Experimental Methodology to Characterize the Uniaxial Fracture Strain of Sheet Metals Using the Conical Hole Expansion Test

Fracture characteristics of advanced high strength steels during hole expansion test

Relationships Between Stretch-Flangeability and Microstructure-Mechanical Properties in Ultra-High-Strength Dual-Phase Steels

Experimental Research of Prestrain Effects on Mechanical Behavior of Dual Phase Steel

Heterogeneous local plastic deformation of interstitial free steel revealed using in-situ tensile testing and high angular resolution electron backscatter diffraction

Development of Experimental Method to Improve Sheet Metal Formability by Transverse Normal Stress

Interaction Effect of Cracks and Anisotropic Influence on Degradation of Edge Stretchability in Hole-Expansion of Advanced High Strength Steel

Damage Evolution in Complex-Phase and Dual-Phase Steels during Edge Stretching

On the critical role of martensite hardening behavior in the paradox of local and global ductility in dual-phase steels

Strain-Hardening Behaviors of Dual Phase Steels with Microstructure Features

Influence of Post-Weld Heat Treatment on Microstructural and Mechanical Properties of Dual-Phase Steel Gas Metal Arc-Welded Joints

Increasing the Forming Limits in Hole Flanging of Dual-Phase (DP) 1000 Steel Using Punch Rotation

Effect of Friction Stir Process on Hole Expansion Behavior of Dual Phase Steel

Investigation on strain localization and hardening of dual-phase steel by hetero-deformation induced stress

Influence of Curvature Variation on Edge Stretchability in Hole Expansion and Stretch Flanging of Advanced High-Strength Steel