Abstract:Introduction: Intraocular lenses (IOL) should remain in the eye for life after implantation into the capsular bag during cataract surgery. The material must meet various requirements. It is crucial that the material has the best biocompatibility, and it should be flexible and soft for best possible implantation process but also sufficiently stable and stiff for good centering in the eye and posterior capsule opacification prevention. Methods: In this laboratory experiment, we used nano-indentation for the mechanical assessment of three hydrophobic acrylic (A, B, C), three hydrophilic acrylic (D, E, F), and one silicone (G) intraocular lens. We wanted to determine whether some react more sensitively to touching/handling than others. The indentation elastic modulus and the creep were obtained from the force displacement curve. For measuring penetration depth and testing of possible damage to the intraocular lenses, the samples were measured at room temperature. A 200-µm-diameter ruby spherical tipped indenter was used for all the tests. Indentations were made to three different maximum loads, namely 5 mN (milli Newton), 15 mN, and 30 mN and repeated three times. Results: The lowest penetration depth (12 µm) was observed with IOL B. However, IOL A, D, and F showed similar low penetration depths (20, 18, and 23 µm, respectively). Lenses C and E showed slightly higher penetration depths of 36 and 39 µm, respectively. The silicone lens (G) showed the greatest penetration depth of 54.6 µm at a maximum load of 5 mN. With higher maximal loads (15 and 30 mN) the penetration depth increased significantly. Lens C, however, showed the same results at both 15 and 30 mN with no increase of penetration depth. This seems to fit well with the material and manufacturing process of the lens (lathe-cut). During the holding time of 30 s at constant force all six acrylic lenses showed a significant increase of the creep (CIT 21-43%). Lens G showed the smallest creep with 14%. The mean indentation modulus (EIT) values ranged from 1 to 37 MPa. IOL B had the largest EIT of 37 MPa, which could be caused by the low water content. Conclusion: It was found that results correlate very well with the water content of the material in the first place. The manufacturing process (molded versus lathe-cut) seems to play another important role. Since all included acrylic lenses are very similar, it was not surprising that the measured differences are marginal. Even though hydrophobic materials with lower water content showed higher relative stiffness, penetration and defects can also occur with these. The surgeon and scrub nurse should always be aware that macroscopic changes are difficult to detect but that defects could theoretically lead to clinical effects. The principle of not touching the center of the IOL optic at any time should be taken seriously.

Evaluation of Parameters and Nozzle Tip Damage after Clinical Use of Three Hydrophilic Intraocular Lens Injector Models

A laboratory evaluation of nozzle tip damage in four generations of intraocular lens injector systems using a self-developed damage scale

Characterisation of Intraocular Lens Injectors

Two Techniques of Posterior Chamber Intraocular Lens (IOL) Implantation by a 4-Point Ciliary Sulcus Suture Fixation Technique Combined with Vitrectomy

CARING: Cannula for Alleviation of Retinal Injury Caused by Needle Fluidic Gashing

Nano-Indentation to Determine Mechanical Properties of Intraocular Lenses: Evaluating Penetration Depth, Material Stiffness, and Elastic Moduli

Mechanistic Analysis of Solid–liquid Flow During Injection

Examining Penetration and Residual Depth in Modern Acrylic Foldable Intraocular Lenses: A Laboratory Study Using Differential Interference Contrast Microscopy to Compare Hydrophilic and Hydrophobic Materials

Observation on Changes of Anterior Chamber and Chamber Angle Structures after Posterior Chamber Phakic Intraocular Lens Implantation by Ultrasound Biomicroscopy

Evaluating impact of Nd: YAG laser associated defects on optical quality of hydrophilic and hydrophobic intraocular lenses using visualization of light propagation and USAF test targets

Comparisons of the energy efficiency and intraocular safety of two torsional phacoemulsification tips

Optical Imaging Quality Change of Multifocal Intraocular Lens Following Nd∶YAG Laser Damage

Laboratory assessment of thermal characteristics of three phacoemulsification tip designs operated using torsional ultrasound

Examination of phacoemulsification tips after different numbers of cataract surgeries

Drug Delivery from a Ring Implant Attached to Intraocular Lens: An in-silico Investigation

Safety of Intraocular Pressure Measurement Using Air-Puff Tonometer after Implantable Collamer Lens Implantation.

Theoretical study on the need for laser iridotomy in an implantable collamer lens with a hole using computational fluid dynamics

A Novel 3D High Resolution Imaging Method Using Correlative X-Ray and Electron Microscopy to Study Neodymium-Doped Yttrium Aluminum Garnet Laser-Induced Defects in Intraocular Lenses

Tilt, Decentration, and Internal Higher-Order Aberrations of Sutured Posterior-Chamber Intraocular Lenses in Patients with Open Globe Injuries.

When to change needles during neuromodulator injections—An electron‐microscopy investigation into needle tip deformation

Comparison of the Residual Amount of an Ophthalmic Viscosurgical Device Among Different Types of Intraocular Lens Implants in vitro