Abstract:Objective: The aim of this study was to evaluate the strength of the locking plate and lag screw construct that is applied in two different working lengths on the simple distal femur fracture model with a finite element analysis (PEA) method. Methods: From the computerized tomography scan data of a 60-year-old healthy male, the AO/OTA 33A1-type fracture model was simulated; the fracture gap was stabilized with the models of locking plate construct with (groups C and D) or without an interfragmentary lag screw (groups A and B). Furthermore, 102-mm plate (groups A and C) and 82-mm plate working lengths (groups B and D) were tasted using FBA. Two loading conditions (axial compression and torsion) were applied at the center of the femoral head. Construct stiffness, interfragmentary micromotion, and the peak von Mises stress (VMS) on the plate were assessed. Results: Group D provided the highest axial stiffness (1347 M/mm), and group A was the weakest (439 N/mm). With the lag screw, shear micromotion remained generally low compared with that without the screw for all axial and torsional load levels and for both plate working lengths, i.e.. 0.23 mm with lag screw versus 0.43 mm without lag screw (102 mm working length, 700 N). The percentage decreases of shear micromotion under axial (350/700/1400 N) and torsional loads for the 102-mm working length were >22% and 73%, respectively; while those for the 82-mm working length were >28% and 33%, respectively. The reduction of axial micromotion was observed with the lag screw for all axial load levels as well as for both plate working lengths. i.e.. 0.33 mm with lag screw versus 0.87 mm without lag screw (102-mm working length, 700 N). The percentage decreases of axial micromotion under axial loading (350/700/1400 N) for 102 mm and 82 mm working lengths were >42% and 50%, respectively. The peak VMS on the plate stayed generally low with lag screw compared with without lag screw throughout all tested load levels, as well as for both plate working lengths, i.e., 124.26 MPa versus 244.39 MPa (102 nun working length, 700 N). The percentage decreases of the peak VMS under axial (350/700/1400 N) and torsional loads for the 102-mm working length were >40% and 69%. respectively, while those for the 82-mm working length were >47% and 61%. respectively. Conclusion: The current PEA concludes that in a simple distal femur fracture, adding a lag screw to a locking plate construct provides better torsional stability with a 102-mm plate working length and better axial stability with a 82-mm plate working length. Additionally, the strength of the materials is increased and implant failure can be minimized by using this technique.

Biomechanical analysis of combi-hole locking compression plate during fracture healing: A numerical study of screw configuration

Failure Analysis of a Locking Compression Plate with Asymmetric Holes and Polyaxial Screws

Biomechanical Comparison of Locking Plate and Cancellous Screw Techniques in Medial Malleolar Fractures: A Finite Element Analysis.

Locking Plates With Computationally Enhanced Screw Trajectories Provide Superior Biomechanical Fixation Stability of Complex Proximal Humerus Fractures

Mechanically compliant locking plates for diaphyseal fracture fixation: A biomechanical study

Screw and plate fixation for fractures of tibial shaft: three-dimensional finite element analysis

Comparison of a Multidimensional Cross Locking Plate Versus a Locking Compression Plate for the Treatment of Femoral Shaft Nonunion: Finite Element Analysis

Biomechanical testing of a computationally optimized far cortical locking plate versus traditional implants for distal femur fracture repair

Biomechanical Analysis of Locking Plates for Fixation of Metacarpal Shaft Fractures: A Finite Element Analysis.

Biomechanics and finite element analysis comparing posterior T-plates with LCP for fixation of posterolateral tibial plate fractures

Finite Element Analysis of an Intramedulary Anatomical Strut for Proximal Humeral Fractures with Disrupted Medial Column Instability: A Cohort Study.

Interfragmentary lag screw and locking plate combination in simple distal femoral fractures: A finite element analysis

Finite element model with realistic bone geometries for the optimal design of internal fixation during the fibula healing process

Computational analysis of the biomechanical stability of internal fixation of the lateral tibial plateau fracture: A mechanical stability study

Biomechanical study of the stiffness of the femoral locking compression plate of an external fixator for lower tibial fractures

Effect of different composite plates on the healing of femoral fractures

Finite element method-based simulation on bone fracture fixation configuration factors for biodegradable embossed locking compression plate

A Mechanical Comparison of the Locking Compression Plate (LCP) and the Low Contact-Dynamic Compression Plate (DCP) in an Osteoporotic Bone Model

Comprehensive biomechanical analysis of three clinically used fixation constructs for posterior malleolar fractures using cadaveric and finite element analysis

Biomechanical analysis of four augmented fixations of plate osteosynthesis for comminuted mid-shaft clavicle fracture: A finite element approach

Effect of Plate–Bone Distance and Working Length on 2.0-mm Locking Construct Stiffness and Plate Strain in a Diaphyseal Fracture Gap Model: A Biomechanical Study