Abstract:Objectives: This study aims to investigate bond strength between zirconia and resin cement through surface treatments with Er: YAG laser, Nd: YAG laser, and Si-Zr coating. Methods: Seventy-five round pre-sintered zirconia discs with a diameter of 18 mm and a thickness of 1.5 mm were prepared by a powder compactor. Fifty discs were randomly divided into five groups of 10 discs each and were subjected to five surface treatments: no treatment (control group), sandblasting with alumina particles (sandblasting group), Er: YAG laser treatment (Er: YAG laser group), Nd:YAG laser treatment (Nd: YAG laser group), and Si-Zr coating treatment (Si-Zr coating group). The discs were then bonded to composite resin columns with resin cement. The shear bond strength of each group was tested with a universal tester. Roughness tester, scanning electron microscope (SEM), and energy dispersive spectroscopy were used to analyze surface performance. Results: The bond strength of the Si-Zr coating group was higher than that of the remaining groups (P<0.05). The difference in bond strength between the sandblasting group and the Er: YAG laser group was not statistically significant (P>0.05), but both of them had higher bond strength than the Nd: YAG laser group (P<0.05). The Si-Zr coating group had the highest surface roughness (P<0.05). The surface roughness of the sandblasting, Er: YAG laser, and Nd: YAG laser groups was higher than that of the control group (P<0.05), but the difference among the three groups was not statistically significant (P>0.05). SEM observations showed irregular scratches on the surface of the sandblasting group and large pits with holes on the surface of the Er: YAG and Nd: YAG laser groups. In the Er: YAG laser group, the crystal structure was replaced by a smooth surface with a large amount of microcracks due to partial melting. Complex porous structures that comprised "island-like" structures and mass pores among the grains were observed on the surface of the Si-Zr coating. Only Zr, O, and Y were detected on the surfaces of the control, Er: YAG laser, and Nd: YAG laser groups. Al was found on the surface of the sandblasted group, and a higher proportion of Si was detected on the surface of the Si-Zr coating group. Conclusions: Er: YAG laser and Nd: YAG laser treatment on the zirconia ceramic surface could increase roughness and improve the bond strength to resin cement. Si-Zr coating treatment is an effective alternative for increasing the roughness and bond strength of zirconia surface and is superior to sandblasting and laser treatments.

Effects of silica sputtering on adhesion between zirconia and composite resin cores

The Effect of Nano-Silica Surface Infiltration on Bond Strength of a Phosphate-Monomer-containing Composite Cement to Zirconia.

Ultrasonic cleaning of silica-coated zirconia influences bond strength between zirconia and resin luting material

A Novel Porous Silica-Zirconia Coating for Improving Bond Performance of Dental Zirconia

The effect of adhesive surface with porcelain sintering and two silane coupling agents on the adhesive properties of zirconia

[Influence of Tribochemical Silica Coating on Shear Bond Strength of a Dental Zirconia Ceramic to Resin Cements].

[Effect of SiO2-ZrO2 slurry coating on shear bond strength of zirconia to resin cement]

In vitro comparative study between adhesion forces obtained on zirconia ceramic micromechanically treated with femtosecond laser (1027 nm), carbon dioxide laser (10,600 nm), and aluminum-oxide particles

Effect of air abrasion particles on the bond strength of adhesive resin cement to zirconia core

Different surface treatments and adhesive monomers for zirconia-resin bonds: A systematic review and network meta-analysis

Improving the bonding stability between resin cements and zirconia-based ceramic using different surface treatments

[Effects of Different Surface Treatments on the Zirconia-Resin Cement Bond Strength].

Effects of Sandblasting on Surface Character and Resin Bond of Zirconia Ceramic

Effect of air abrasion and dye on the surface element ratio and resin bond of zirconia ceramic

Effect of laser and coating surface treatment on the bond strength of zirconia ceramics

Bonding Effectiveness of Veneering Ceramic to Zirconia after Different Grit-Blasting Treatments

Long-term Bond Strength between Layering Indirect Composite Material and Zirconia Coated with Silicabased Ceramics

Effect of hot chemical etching on bond strength of zirconia to resin

Exploring Zirconia Adhesion: Pre and Postsintering Physical Surface Treatment, Chemical Treatment, and Cement Interactions

Selective Infiltrated Etching to Surface Treat Zirconia Using a Modified Glass Agent.

The Shear Bond Strength of Resin-Based Luting Cement to Zirconia Ceramics after Different Surface Treatments