Abstract:The need for 2219 aluminum alloy and 2195 Al–Li alloy dissimilar friction stir welding (FSW) arises as the conventional 2219Al alloy was gradually replaced by the novel 2195Al alloy in fabrication of fuel tanks. However, the systematic investigation about the effect of welding parameters and material positioning on the microstructure evolution and mechanical properties of dissimilar FSW 2219Al/2195Al joints is lacking. In the present study, 2219Al-T8/2195Al-T8 plates were subjected to FSW under rotation rates of 800–1200 rpm and welding speeds of 200–800 mm min −1 with placing 2219Al-T8 alloys on the advancing side (AS) and retreating side (RS), respectively. The results showed that sound FSW joints were obtained under all the welding conditions. Welding parameters and material positioning affected the joint strength and fracture failure behavior. The FSW thermal cycle resulted in low hardness zones (LHZs) on both the 2219Al-T8 and 2195Al-T8 sides. The LHZ on the 2219Al-T8 side, characterized by partial coarsening of θ ′ (Al 2 Cu) precipitates and dissolution of the residual precipitates, showed the minimum hardness in the entire FSW joints. When 2219Al-T8 alloy was placed on the AS, the LHZ on the 2219Al-T8 side experienced higher peak temperature, and therefore more dissolution of θ ′ than that on the RS, thereby obtaining higher tensile strength. The tensile strength of the FSW joints at room temperature and − 196 °C largely increased as the welding speed increased from 200 to 400 mm min −1 . The FSW joints presented much higher tensile strength at − 196 °C than that at room temperature under the identical welding parameters and material position. The FSW joints fractured along the LHZ on the 2219Al-T8 side during tension. For the bending testing, the up and down bending failure angles were about 91–117° and 88–109°, respectively, with the weak zone appearing in "S" line or HAZ on the 2195Al-T8 side.

Softening issue in the thick-plate friction pull plug welding of AA2219-T87

High-quality Friction Pull Plug Welding of AA2219-T87 Plate with a Thickness of 18 Mm: Experimental Characterization on Shaping, Microstructure and Mechanical Properties

Microstructure and mechanical properties of friction pull plug welding for 2219-T87 aluminum alloy with tungsten inert gas weld

Correlation Between Microstructure and Mechanical Properties of 2219-T8 Aluminum Alloy Joints by VPTIG Welding

Effect of softening of 6082-T6 aluminum alloy CMT welded joints on mechanical properties and fracture behavior

Study on the Optimization of the Tensile Properties of an Al-Li Alloy Friction Stir-Welding T-Joint

Dissimilar friction stir welding of 2219-T8 and 2195-T8 aluminum alloys: part I—microstructure evolution and mechanical properties

Interface Behaviours and Mechanical Properties of Filling Friction Stir Weld Joining AA 2219

Improving joint performance of friction stir welded 2195-O Al–Li alloy by post-weld heat treatment and rolling deformation

Microstructures and Mechanical Properties of Al-Li Alloy Friction Stir Weld

Review of Techniques for Improvement of Softening Behavior of Age-Hardening Aluminum Alloy Welded Joints

Microstructure and mechanical properties of self-reacting friction stir welded AA2219-T87 aluminium alloy

Effect of Tool Traverse Speed on Joint Line Remnant and Mechanical Properties of Friction Stir Welded 2195-T8 Al–Li Alloy Joints

"Anneal" softening effect of 2219-T8 aluminum alloy joint during welding and its influence on prediction of welding residual stresses

X-ray Microscopic and Thermodynamic Model Assessments of Softening in TIG-Welded AA 6061-T651

Influence of Welding Combined Plastic Forming on Microstructure Stability and Mechanical Properties of Friction Stir-Welded Al-Cu Alloy

Softening Phenomenon of Heat-Affected Zone in Laser Welding of 6082 Al Alloys with Filler Wire

Enhancing Formability of AA2219 Aluminum Alloy Friction Stir Welded Blanks with Preheating Treatment

Friction Stir Welding of Al-Li AA2199: Parameters, Precipitates and Post Weld Heat Treatment

Formation Mechanisms and Control Strategies of FQZ Softening in Al–Li Alloy Welded Joint

Experimental Study on Mechanical Behaviour of Friction Stir Welded Aluminium Alloy Butt Joints