Abstract:Introduction: The cervical spine, pivotal for mobility and overall body function, can be affected by cervical spondylosis, a major contributor to neural disorders. Prevalent in both general and military populations, especially among pilots, cervical spondylosis induces pain and limits spinal capabilities. Anterior Cervical Discectomy and Fusion (ACDF) surgery, proposed by Cloward in the 1950s, is a promising solution for restoring natural cervical curvature. The study objective was to investigate the impacts of ACDF implant design on postsurgical cervical biomechanics and neurorehabilitation outcomes by utilizing a biofield head-neck finite element (FE) platform that can facilitate scenario-specific perturbations of neck muscle activations. This study addresses the critical need to enhance computational models, specifically FE modeling, for ACDF implant design. Materials and methods: We utilized a validated head-neck FE model to investigate spine-implant biomechanical interactions. An S-shaped dynamic cage incorporating titanium (Ti) and polyetheretherketone (PEEK) materials was modeled at the C4/C5 level. The loading conditions were carefully designed to mimic helmet-to-helmet impact in American football, providing a realistic and challenging scenario. The analysis included intervertebral joint motion, disk pressure, and implant von Mises stress. Results: The PEEK implant demonstrated an increased motion in flexion and lateral bending at the contiguous spinal (C4/C5) level. In flexion, the Ti implant showed a modest 5% difference under 0% activation conditions, while PEEK exhibited a more substantial 14% difference. In bending, PEEK showed a 24% difference under 0% activation conditions, contrasting with Ti's 17%. The inclusion of the head resulted in an average increase of 18% in neck angle and 14% in C4/C5 angle. Disk pressure was influenced by implant material, muscle activation level, and the presence of the head. Polyetheretherketone exhibited lower stress values at all intervertebral disc levels, with a significant effect at the C6/C7 levels. Muscle activation level significantly influenced disk stress at all levels, with higher activation yielding higher stress. Titanium implant consistently showed higher disk stress values than PEEK, with an orders-of-magnitude difference in von Mises stress. Excluding the head significantly affected disk and implant stress, emphasizing its importance in accurate implant performance simulation. Conclusions: This study emphasized the use of a biofidelic head-neck model to assess ACDF implant designs. Our results indicated that including neck muscles and head structures improves biomechanical outcome measures. Furthermore, unlike Ti implants, our findings showed that PEEK implants maintain neck motion at the affected level and reduce disk stresses. Practitioners can use this information to enhance postsurgery outcomes and reduce the likelihood of secondary surgeries. Therefore, this study makes an important contribution to computational biomechanics and implant design domains by advancing computational modeling and theoretical knowledge on ACDF-spine interaction dynamics.

Upright Magnetic Resonance Imaging Study of Cervical Flexor/Extensor Musculature and Cervical Lordosis in Females After Helmet Wear

Evaluation Of Neck Fatigue Caused By Wearing Helmet In Motion: An Electromyography Study

Effect of Helmet Mass and Mass Center on Neck Muscle Strength in Military Pilots

Firefighter Helmets and Cervical Intervertebral Kinematics: An OpenSim-Based Biomechanical Study

Biomechanical analysis of cervical spine (C2–C7) at different flexed postures

Wearable neck assistive device strain evaluation study on surface neck muscles for head/neck movements

The effect of helmet mass and aircraft acceleration on cervical spine loads during typical fast jet aircraft pilot head motions

Abnormal Static Sagittal Cervical Curvatures following Motor Vehicle Collisions: A Retrospective Case Series of 41 Patients before and after a Crash Exposure

Multifidus muscle size changes at different directions of head and neck movements in females with unilateral chronic non-specific neck pain and healthy subjects using ultrasonography

The effects of 12 weeks of functional strength training on muscle strength, volume and activity upon exposure to elevated Gz forces in high-performance aircraft personnel

Assessment of potential strain injury to rectus capitis posterior minor muscles during whiplash type distortions of the cervical spine

Mechanisms of cervical spine injury and coupling response with initial head rotated posture - implications for AIS coding

The deflection of fatigued neck

Variability in Body Shape, Superficial Soft Tissue Geometry, and Seatbelt Fit Relative to the Pelvis in Automotive Postures—Methods for Volunteer Data Collection With Open Magnetic Resonance Imaging

Neck forces and moments and head accelerations in side impact

Effectiveness of strengthening deep cervical flexors using pressure biofeedback on vertical mandibular opening & craniovertebral angle in young adults with forward head posture - An experimental study

Comparison of small female occupant model responses with experimental data in a reclined posture

Development and validation of a geometrically personalized finite element model of the lower ligamentous cervical spine for clinical applications

Effects of Cervical Spine Exercise Protocol on Neck Pain, Pericervical Muscle Endurance, and Range of Motion in Medical Students: A Prospective Study

Effect of reciprocal headgear forces on the calvarium: A finite element study

Implant Design and Cervical Spinal Biomechanics and Neurorehabilitation: A Finite Element Investigation