Paraffin beads can replace mineral oil as an evaporation barrier in PCR.

L. Wainwright,H. Seifert

BioTechniques

Abstract:

What problem does this paper attempt to address?

Phase Change Materials of Paraffin in H-Bn Porous Scaffolds with Enhanced Thermal Conductivity and Form Stability

Zhenchao Qian,Heng Shen,Xin Fang,Liwu Fan,Ning Zhao,Jian Xu

DOI: https://doi.org/10.1016/j.enbuild.2017.11.033

IF: 7.201

2017-01-01

Energy and Buildings

Abstract:Low thermal conductivity and leakage after melting are the two main issues limited the application of phase change materials (PCMs). Here, to improve the thermal conductivity and hamper the leakage after melting, PCMs were fabricated by infiltrating paraffin into h-BN porous scaffolds with continuous thermal conductive paths. The latent heat of fusion of the resultant PCMs containing 18wt% h-BN was 165.4±1.7J/g, and the thermal conductivity was as high as 0.85W/mK. The thermal conductivity increased approximately 600% compared to the pure paraffin, and was over twice of the composites fabricated by conventional blending of paraffin and h-BN. The enhanced thermal conductivity obviously shortened the phase change process, indicating more efficient in energy storage and release. In addition, the h-BN scaffolds endowed the PCMs shape stability under molten state and prevented the leakage of molten paraffin. This approach to fabricate form-stable PCMs with high thermal conductivity may extend to other thermal management applications.
Surfactant and Oil Formulations for Monodisperse Droplet Emulsion PCR

Fangli Zhang,Peiyu Liao,Yue Sun,Zitian Chen,Yuhong Pang,Yanyi Huang

DOI: https://doi.org/10.1039/d0lc00052c

IF: 7.517

2020-01-01

Lab on a Chip

Abstract:Emulsion PCR has become a popular and widely applied method in biological research and clinical diagnostics to provide evenly amplified products and perform highly quantitative counting of target sequences. However, there is still a lack of information to support further development of appropriate water-in-oil emulsion formulations, which need to be both thermally and mechanically stable for digital amplification reactions. Here, we present a systematic survey of the oil and surfactant components of stable monodisperse w/o emulsions suitable for use with our previously developed micro-capillary array (MiCA)-based centrifugal emulsion generation method. Our findings show that a binary formula consisting of isopropyl palmitate and a silicone copolymer demonstrated the best performance, and provided a general guideline for the development of emulsion systems for digital PCR and emulsion amplification applications.
A Thermosetting Oil For Droplet-Based Real-Time Monitoring Of Digital Pcr And Cell Culture

Wenshuai Wu,Shufang Zhou,Jiumei Hu,Guoping Wang,Xiong Ding,Tong Gou,Jingjing Sun,Tao Zhang,Ying Mu

DOI: https://doi.org/10.1002/adfm.201803559

IF: 19

2018-01-01

Advanced Functional Materials

Abstract:Real-time observation of small volumes helps to understand phenomena ranging from reaction kinetics to cellular heterogeneity. However, high-throughput real-time monitoring systems based on droplets are rarely reported due to droplet motion and coalescence. Herein, a thermosetting oil is developed as a continuous phase to solve these problems through transforming into elastic solid after droplet generation. The thermosetting oil consists of silicon oil, nonionic surfactant, vinyl silicone oil, hydrosilicone oil, and Pt catalyst. Using Pt as the catalyst, the polymerization of this mixture can be accomplished in 72 min and 37 s at 37 and 95 degrees C, respectively, based on the hydrosilation of vinyl silicone oil and hydrosilicone oil without other inducers (e.g., UV, Ca2+). Droplet-based real-time monitoring of digital polymerase chain reaction (PCR) and cell culture is successfully achieved using this thermosetting oil, demonstrating that droplets motion and coalescence can be eliminated by the crosslinking material without the influence on bioreactions. In addition, the PCR products can be totally recovered from microcapsules created by this oil for further analysis. Thus, the newly developed oil allows real-timely monitoring individual droplets in a high-throughput manner, as well as has potential for other bioreactions and cell-based assays.
Dissolvable Polyacrylamide Beads for High-Throughput Droplet DNA Barcoding

Yongcheng Wang,Ting Cao,Jina Ko,Yinan Shen,Will Zong,Kuanwei Sheng,Wenjian Cao,Sijie Sun,Liheng Cai,Ying-Lin Zhou,Xin-Xiang Zhang,Chenghang Zong,Ralph Weissleder,David Weitz

DOI: https://doi.org/10.1002/advs.201903463

IF: 15.1

2020-01-01

Advanced Science

Abstract:Droplet-based single cell sequencing technologies, such as inDrop, Drop-seq, and 10X Genomics, are catalyzing a revolution in the understanding of biology. Barcoding beads are key components for these technologies. What is limiting today are barcoding beads that are easy to fabricate, can efficiently deliver primers into drops, and thus achieve high detection efficiency. Here, this work reports an approach to fabricate dissolvable polyacrylamide beads, by crosslinking acrylamide with disulfide bridges that can be cleaved with dithiothreitol. The beads can be rapidly dissolved in drops and release DNA barcode primers. The dissolvable beads are easy to synthesize, and the primer cost for the beads is significantly lower than that for the previous barcoding beads. Furthermore, the dissolvable beads can be loaded into drops with >95% loading efficiency of a single bead per drop and the dissolution of beads does not influence reverse transcription or the polymerase chain reaction (PCR) in drops. Based on this approach, the dissolvable beads are used for single cell RNA and protein analysis.
Creating biocompatible oil-water interfaces without synthesis: direct interactions between primary amines and carboxylated perfluorocarbon surfactants

Cheryl J DeJournette,Joonyul Kim,Haley Medlen,Xiangpeng Li,Luke J Vincent,Christopher J Easley

DOI: https://doi.org/10.1021/ac4026048

2013-11-05

Abstract:Currently, one of the most prominent methods used to impart biocompatibility to aqueous-in-oil droplets is to synthesize a triblock copolymer surfactant composed of perfluoropolyether and polyether blocks. The resulting surfactants (EA surfactant, KryJeffa, etc.) allow generation of highly biocompatible droplet surfaces while maintaining the heat stability of the starting material. However, production of these surfactants requires expertise in synthetic organic chemistry, creating a barrier to widespread adoption in the field. Herein, we describe a simple alternative to synthetic modification of surfactants to impart biocompatibility. We have observed that aqueous-in-oil droplet surfaces can be made biocompatible and heat stable by merely exploiting binding interactions between polyetherdiamine additives in the aqueous phase and carboxylated perfluorocarbon surfactants in the oil phase. Droplets formed under these conditions are shown to possess biocompatible surfaces capable of supporting picoliter-scale protein assays, droplet polymerase chain reaction (PCR), and droplet DNA amplification with isothermal recombinase polymerase amplification (RPA). Droplets formed with polyetherdiamine aqueous additives are stable enough to withstand temperature cycling during PCR (30-40 cycles at 60-94 °C) while maintaining biocompatibility, and the reaction efficiency of RPA is shown to be similar to that with a covalently modified surfactant (KryJeffa). The binding interaction was confirmed with various methods, including FT-IR spectroscopy, NMR spectroscopy, electrospray ionization mass spectrometry (ESI-MS), and fluorescence microscopy. Overall, our results suggest that, by simply introducing a commercially-available, polyetherdiamine additive (Jeffamine ED-900) to the aqueous phase, researchers can avoid synthetic methods in generating biocompatible droplet surfaces capable of supporting DNA and protein analysis at the subnanoliter scale.
Evaporation Phenomenon in Micro Polymerase Chain Reaction (μpcr) System and a Possible Electrowetting Solution

Hao Tian,Jian Qin,Tao Deng,Rong Zhang,Chong Liu,Taihong Wang,Zewen Liu

DOI: https://doi.org/10.1163/156856111x600497

IF: 2.431

2012-01-01

Journal of Adhesion Science and Technology

Abstract:It is found that the sample leakage and evaporation are two major drawbacks in the stationary micro polymerase chain reaction (mu PCR) system. Experiments were performed to analyze the evaporation phenomenon and to find a possible solution. Electrochemical method was used to investigate the residual solution inside the PCR chamber. Results indicate that the system covered with poly(dimethylsiloxane) (PDMS) membrane may hold the methylene blue (MB) solution inside the chamber intact for at least 500 s at 26 degrees C, whereas the remaining aqueous solution is only 30% at 91.2 degrees C. An electrowetting method is proposed for stationary mu PCR, where a complete filling of the solution inside the reaction chamber is important for trace DNA amplification and detection. (C) Koninklijke Brill NV, Leiden, 2011
Paraffin /poly(methyl Methacrylate) Blends As Form-Stable Phase Change Materials for Thermal Energy Storage

Xiao-Mei Tong,Min Zhang,Ling Song,Pan Ma

DOI: https://doi.org/10.4028/www.scientific.net/amr.183-185.1573

2011-01-01

Advanced Materials Research

Abstract:A series of paraffin /poly (methyl methacrylate) blends were prepared as new kinds of form-stable phase change materials by encapsulation of paraffin into PMMA. The blends were prepared at different mass fractions of paraffin. The form-stable paraffin /PMMA blends were characterized using optic microscopy (OM) and Fourier transform infrared (FT-IR) spectroscopy. Thermal characteristics were measured by using thermo gravimetric analysis （TGA） and differential scanning calorimetry (DSC) technique. On the basis of all results, it was concluded that paraffin is encapsulated by PMMA. The blends have good thermal properties and degrade in two distinguishable steps. They have good energy storage capacity and melt at 58-60 °C.The blends have different degrees of hydrophobic. These form-stable paraffin /PMMA blends have important potential for some practical latent heat thermal energy storage applications.
Inhibiting wax deposition using palm oil additives

Thevaruban Ragunathan,Colin D. Wood,Hazlina Husin

DOI: https://doi.org/10.1007/s13202-021-01318-8

IF: 2.508

2021-10-09

Journal of Petroleum Exploration and Production Technology

Abstract:Abstract Among the flow assurance problems that the petroleum industry faces, the deposition of paraffin waxes on to the wall of the pipeline is the most challenging. The challenge arises when the crude oil temperature decreases below the wax appearance temperature which prompts wax crystallization in the crude oil. An efficient method in remedying paraffin wax deposition is the utilization of chemical inhibitors. However, currently used chemical inhibitors are costly and environmentally harmful if a spillage occurs. Therefore, the use of biodegradable or environmentally friendly inhibitors as potential chemical inhibitors is being studied by various researchers. This study investigated oleic acid, poly (ethylene-co-vinyl acetate) (EVA) and triethanolamine (TEA) as inhibitors that perform based on the van der Waals intermolecular interaction between the main wax component molecule eicosane C 20 H 42 using molecular dynamics simulations Material Studio 8.0 software package. In order to analyse the desired structural property which is the radial distribution function (RDF), COMPASS force field was used. The RDF and g(r) function portrayed the functional atoms which aid in inhibiting the agglomeration and crystallization of the wax crystal formation. The presence of a carbonyl oxygen in oleic acid plays a vital role to inhibit the wax formation through the van der Waals interaction between active hydrogen atoms in eicosane molecule. Therefore, the chances of wax inhibition in eicosane are higher by introducing oleic acid as an inhibitor as compared to EVA and TEA. The results were then validated experimentally utilizing a cold finger technique under static condition.

energy & fuels,geosciences, multidisciplinary,engineering, petroleum
Comparison of Methods for Extracting DNA from Formalin-Fixed Paraffin Sections for Nonisotopic PCR

Thomas S. Frank,Suzette M. Svoboda-Newman,Eric D. Hsi

DOI: https://doi.org/10.1097/00019606-199609000-00012

1996-09-01

Diagnostic Molecular Pathology

Abstract:DNA was extracted from unstained 5-microns sections of neutral buffered 10% formalin-fixed paraffin-embedded tissue by proteinase K digestion without detergents followed by boiling, proteinase K digestion with ionic detergents with and without phenol chloroform extraction and ethanol precipitation, sonication with proteinase K followed by boiling, or boiling alone. Serial 1:10 dilutions of the extracted DNA were subject to polymerase chain reaction (PCR) amplification of a 255-bp portion of the p53 gene. Digestion with proteinase K without ionic detergents followed by boiling (without phenol chloroform extraction) gave the best yield, enabling visualization of ethidium bromide-stained PCR product from a DNA dilution corresponding to 0.1 mm2 of tissue containing of the order of 10(3) nuclear profiles. Proteinase K digestion with detergents followed by phenol-chloroform extraction was no more effective than simple boiling. Although the success of PCR from preserved tissue will vary with the fixative and size of the amplified fragment, DNA extracted with this optimized method can be used for identification of viruses, loss of heterozygosity, and immunoglobulin gene rearrangements in paraffin-embedded tissue without radioisotopes.

English Else
A new method for phenotyping proliferating cell nuclear antigen positive cells using flow cytometry: implications for analysis of the immune response in vivo.

U. Kühn,U. Lempertz,J. Knop,D. Becker

DOI: https://doi.org/10.1016/0022-1759(94)00287-7

1995-02-27

Abstract:
Optimization of on-bead emulsion polymerase chain reaction based on single particle analysis

Ryan H.P. Siu,Yang Liu,Kaitlin H.Y. Chan,Clara Ridzewski,Liane Siu Slaughter,Angela R. Wu

DOI: https://doi.org/10.1016/j.talanta.2020.121593

IF: 6.1

2021-01-01

Talanta

Abstract:<p>Emulsion polymerase chain reaction (ePCR) enables parallel amplification of millions of different DNA molecules while avoiding bias and chimeric byproducts, essential criteria for applications including next generation sequencing, aptamer selection, and protein-DNA interaction studies. Despite these advantages, ePCR remains underused due to the lack of optimal starting conditions, straightforward methods to evaluate success, and guidelines for tuning the reaction. This knowledge has been elusive for bulk emulsion generation methods, such as stirring and vortexing, the only methods that can emulsify libraries of ≥10<sup>8</sup> sequences within minutes, because these emulsions have not been characterized in ways that preserve the heterogeneity that defines successful ePCR. Our study quantifies the outcome of ePCR from conditions specified in the literature using single particle analysis, which preserves this heterogeneity. We combine ePCR with magnetic microbeads and quantify the amplification yield via qPCR and the proportion of clonal and saturated beads via flow cytometry. Our single particle level analysis of thousands of beads resolves two key criteria that define the success of ePCR: 1) whether the target fraction of 20% clonal beads predicted by the Poisson distribution is achieved, and 2) whether those beads are partially or maximally covered by amplified DNA. We found that among the two concentrations of polymerase tested, only the higher one, which is 20-fold more than the concentration recommended for conventional PCR, could yield sufficient PCR products. Dramatic increases in the concentrations of reverse primer and nucleotides recommended in literature gave no measurable change in outcome. We thus provide evidence-based starting conditions for effective and economical ePCR for real DNA libraries and a straightforward workflow for evaluating the success of tuning ePCR prior to downstream applications.</p>

chemistry, analytical
Improving the phase change properties of paraffin wax by regulating the pore structure and surface properties of silica aerogel

Linhan He,Kaili Ling,Mingjie Wang,Xuejin Zhang,Jing Li,Yao Chen,Yongming Fan

DOI: https://doi.org/10.1016/j.est.2024.110665

IF: 9.4

2024-04-01

Journal of Energy Storage

Abstract:This study highlights the significance of the difference between the melting and solidification temperatures of phase change materials (PCMs) in their practical applications. We incorporated the wood fiber as a support phase and used alkylation to modify the pore structure and surface properties of silica aerogels. The effect of different pore size distributions and surface properties on the phase change properties of PCMs was investigated. The results showed that nanopores increased pressure and the melting point of PCMs while the weak interaction force on the substrate surface decreased their solidification temperature. Furthermore, using matrices with unique properties, such as mesopore and hydrophobic aerogels, proved to be effective in reducing the difference between the melting and solidification temperatures by up to 44.1 % compared to pure paraffin wax. Moreover, hydrophobic groups enhanced the encapsulation performance of the composite, effectively isolating the influence of water.

energy & fuels
Construction and optimization of an efficient breathing-based isothermal emulsion amplification method

Yanting Shen,Fei Tian,Jing Tu,Rui Li,Zhenzhu Chen,Yunfei Bai,Qinyu Ge,Zuhong Lu

DOI: https://doi.org/10.1016/j.aca.2017.03.045

2017-06-22

Abstract:The reaction temperature is one of the main factors that affect the stability of emulsion PCR (emPCR). Focusing on this point, we applied the "DNA breathing" mechanism in BEAMing (Bead, Emulsion, Amplification, and Magnetic) and proposed a more stable emulsion amplification method. Compared to the conventional emPCR, this method provided excellent results. Firstly, more stable emulsion system resulted in higher percentage of single-molecular amplifications (73.17%). Secondly, an ordinary temperature-controlling device was enough. Our outcome showed that the reaction temperature of this method was not strict so that the ordinary temperature-controlling device was enough for it (the heat block sets vs. the PCR instrument: 13.140 ± 0.110 vs. 13.008 ± 0.039, P = 0.120). Thirdly, the single-biotinylated emP1 coated streptavidin beads were stable enough to be used for this method (the control temperature vs. the reaction temperature: 2967.91 ± 409.045 vs. 3026.22 ± 442.129, P = 0.334), which could replace the double-biotinylated emP1 coated beads and was benefit for saving cost. In conclusion, the method presented here with stable emulsion system, simplified temperature-controlling device, and decreased investment would be a highly streamlined and inexpensive option for future single-molecular amplification based researches.
Preparation and mechanism of hyperbranched polymer as paraffin inhibitor and pour point depressant for high waxy crude oil

Yu Huang,Wenmeng Duan,Jie Deng,Jiangdong Chen,Cunchuan Zheng

DOI: https://doi.org/10.1080/1539445x.2024.2432264

2024-11-29

Soft Materials

Abstract:A quaternary polymer paraffin inhibitor and pour point depressant (PIaPPD) with hyperbranched structure was prepared by free radical solution polymerization using docosyl methacrylate (DM), maleic anhydride (MA), methyl methacrylate (MMA) and diethylene glycol dimethacrylate (DEGDMA) as raw materials. The experimental results show that when the dosage of PIaPPD is 250 ppm, the paraffin inhibiting rate of SY1 for high waxy crude oil can reach 83.3%, and the pour point can be reduced by 16°C. At the same time, it has good universality for the crude oil of the remaining 12 different blocks of oil wells. The paraffin inhibiting rate is up to 83.3%, and the crude oil pour point can be reduced by up to 19°C. Through DSC, FTIR, fluorescent inverted microscope, polarizing microscope, XRD, SEM and carbon number distribution analysis, it can be seen that: PIaPPD achieves the purpose of paraffin inhibition and pour point depression by cocrystal-adsorption and dispersion of wax crystals. It mainly achieves the effect of paraffin inhibition and pour point depression by reducing the wax appearance temperature, inhibiting the amount of wax precipitation, destroying the normal growth structure of wax crystals, reducing the strength of wax crystals, reducing paraffin isoparaffins, and inhibiting the precipitation of most medium and low carbon paraffins and a small number of high carbon paraffins. Finally, the wax crystals exist in the crude oil in a less, small and non-aggregated, irregular state in a more dispersed form.

materials science, multidisciplinary
Elaboration and Characterization of Whey Protein Beads by an Emulsification/Cold Gelation Process: Application for the Protection of Retinol

Lucie Beaulieu,Laurent Savoie,Paul Paquin,Muriel Subirade

DOI: https://doi.org/10.1021/bm010082z

2002-01-22

Biomacromolecules

Abstract:Whey protein beads were successfully produced using a new emulsification/cold gelation method. The principle of this method is based on an emulsifying step followed by a Ca(2+)-induced gelation of pre-denatured (80 degreesC/30 min) whey protein. Beads are formed by the dropwise addition of the suspension into a calcium chloride (CaCl(2)) solution. IR results show that bead formation has a pronounced effect on the secondary structure of whey protein, which leads to the formation of intermolecular hydrogen-bonded beta-sheet structures. Their preparation conditions (CaCl(2) concentrations of 10, 15, and 20% (w/w)) influence their sphericity and homogeneity: an increase in CaCl(2) favors regular-shaped beads. The physicochemical and mechanical characterizations of beads were also carried out. Their properties, such as swelling, elasticity, deformability, and resistance at fracture, change according to pH levels (1.9, 4.5, and 7.5) and preparation conditions. Indeed, protein chain networks exhibit different behavior patterns with respect to their charge. Finally, bead degradation by enzymatic hydrolysis reveals that beads are gastroresistant and form good matrixes to protect fat-soluble bioactive molecules such as retinol, that have in vivo intestinal absorption sites. The experiment demonstrated the potential of whey protein beads to protect molecules sensitive (i.e., vitamins) to oxidation.

polymer science,biochemistry & molecular biology,chemistry, organic
B-208 Room Temperature Stable PCR Reagents Preparation Using Capillary-Mediated Vitrification Process

S Renu,Y Peris-Taverner,J Sharpe,S Amle,L Bronsart,P Mohanty,M Shank-Retzlaff

DOI: https://doi.org/10.1093/clinchem/hvae106.568

IF: 12.114

2024-10-27

Clinical Chemistry

Abstract:BackgroundPolymerase chain reaction (PCR) is a sensitive, and most used molecular technique for the disease diagnosis. Reagents used for PCR is available as a one-step and ready-to-use PCR Master Mix, which contains Taq DNA polymerase, dNTPs, MgC1 2 , PCR reaction buffer. However, to preserve bioactivity, PCR reagents must be stored and distributed as frozen. Desiccation of PCR reagents can avoid cold storage and improper handling of wet reagents and its associated errors. We discovered capillary-mediated vitrification (CMV) processes can stabilize different biomolecules and allow them to be stored at ambient temperature. Here, we hypothesized that the CMV process can preserve and improve PCR reagents thermal stability, which will reduce PCR processing time and improve the testing throughput.MethodsThe CMV process was performed by mixing PCR Master Mix individual or all reagents such as Taq DNA polymerase or Hot Start Taq DNA polymerase, dNTPs, 16S rRNA primers, MgC12, and PCR reaction buffer with an excipient buffer and adding the mixture to a porous scaffold. The loaded scaffolds were placed into our vitrification chamber and dried for 30 min. After drying, the CMV-stabilized sample was tested or packed in Mylar pouches and were stored at ambient and elevated temperatures for 42 days. On the day of testing, the stabilized samples were eluted with nuclease-free water and E. coli genomic DNA was added, and the 50 uL reaction was tested by conventional PCR. The PCR product was visualized under agarose gel electrophoresis.ResultsTo assess whether the CMV process maintains PCR reagents activity and not interfering with the assay, the individual PCR reagents and as a Master mix are preserved. The CMV stabilized polymerase enzyme, primer, or dNTPs amplified DNA similar to frozen reagents and produced comparable PCR products. Notably, CMV stabilized PCR Master Mix which contains either Taq DNA polymerase or Hot Start Taq DNA polymerase enzyme, dNTPs, primers, MgC12, and reaction buffer yielded intact amplified PCR product, which is comparable to frozen reagents. Likewise, a high intense PCR product was observed in the stabilized PCR Master Mix reagents when stored at room and elevated temperatures for 42 days.ConclusionsThe study results indicate that the CMV process stabilized and improved the PCR Master Mix reagents activity. The study suggests that the CMV technology has the potential to enable ambient storage and shipping of PCR reagents for molecular diagnostic and other related applications.

medical laboratory technology
Removal of Polymerase Chain Reaction Inhibitors by Electromembrane Extraction

Cong Liu,Daixin Huang,Liuqian Yang,Shifan Wu,Xiantao Shen,Stig Pedersen-Bjergaard,Chuixiu Huang

DOI: https://doi.org/10.1021/acs.analchem.1c01689

IF: 7.4

2021-08-12

Analytical Chemistry

Abstract:Polymerase chain reaction (PCR) technology has become the cornerstone of DNA analysis. However, special samples (e.g., forensic samples, soil, food, and mineral medicine) may contain powerful PCR inhibitors. High levels of inhibitors can hardly be sufficiently removed by conventional DNA extraction approaches and may result in the complete failure of PCR. In this work, the removal of PCR inhibitors by electromembrane extraction (EME) was investigated for the first time. To demonstrate the universality of the approach, EME formats with and without supported membranes (termed parallel-EME and μ-EME, respectively) were employed, and both anionic [humic acid (HA)] and cationic (Ca2+) PCR inhibitors were used as models. During EME, charged inhibitors in the sample migrate into the liquid membrane in the presence of an electric field and might further leech into the waste solution, while PCR analytes remain in the sample. After EME, the clearance values for HA at 0.2 and 2.5 mg mL–1 were 94 and 85%, respectively, and that for Ca2+ (275 mM) was 63%. Forensic PCR–short tandem repeat (PCR–STR) genotyping showed that EME significantly reduced the interference by HA in PCR–STR analysis and displayed a higher HA purge capability compared to existing methods. Furthermore, by combining EME with liquid–liquid extraction or solid-phase extraction, satisfactory STR profiles were obtained from HA-rich blood samples. In addition, false-negative reports of bacterial detection in mineral medicine and shrimps were avoided after the removal of Ca2+ by μ-EME. Our research demonstrates the great potential of EME for the purification of DNA samples containing high-level PCR inhibitors and opens up a new application direction for EME.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acs.analchem.1c01689.Chemicals and samples, chemical structure of HA, growth conditions of S. aureus, setup of the 96-well Pa-EME system, setup of the μ-EME unit, measurement of HA and Ca2+ concentrations, sample purification by existing methods, qPCR procedure, details of the AGCU EX20 STR kit, inhibitory effect of HA on qPCR, visualization of EME results at 0 and 4 V, measurement of DNA concentration by qPCR, comparison of purification performance of the three methods (EME, LLE, and SPE) by STR genotyping, STR profiles of silica-column-based SPE combined with EME for HA-rich blood purification, qPCR results of magnetic bead-based SPE combined with EME for HA-rich blood purification, inhibitory effect of Ca2+ on qPCR, and qPCR results of μ-EME of aqueous extract of S. aureus contaminated shrimp powder (PDF)This article has not yet been cited by other publications.

chemistry, analytical
Polymer-based precipitation preserves biological activities of extracellular vesicles from an endometrial cell line

Ziru Niu,Ronald T K Pang,Weimin Liu,Qian Li,Ranran Cheng,William S B Yeung

DOI: https://doi.org/10.1371/journal.pone.0186534

IF: 3.7

2017-10-12

PLoS ONE

Abstract:Extracellular vesicles (EVs) are membrane-bound vesicles released by cells and act as media for transfer of proteins, small RNAs and mRNAs to distant sites. They can be isolated by different methods. However, the biological activities of the purified EVs have seldom been studied. In this study, we compared the use of ultracentrifugation (UC), ultra-filtration (UF), polymer-based precipitation (PBP), and PBP with size-based purification (PBP+SP) for isolation of EVs from human endometrial cells and mouse uterine luminal fluid (ULF). Electron microscopy revealed that the diameters of the isolated EVs were similar among the tested methods. UF recovered the highest number of EVs followed by PBP, while UC and PBP+SP were significantly less efficient (P<0.05). Based on the number of EVs-to-protein ratios, PBP had the least protein contamination, significantly better than the other methods (P<0.05). All the isolated EVs expressed exosome-enriched proteins CD63, TSG101 and HSP70. Incubation of the trophoblast JEG-3 cells with an equal amount of the fluorescence-labelled EVs isolated by the studied methods showed that many of the PBP-EVs treated cells were fluorescence positive but only a few cells were labelled in the UC- and UF-EVs treated groups. Moreover, the PBP-EVs could transfer significantly more miRNA to the recipient cells than the other 3 methods (P<0.05). The PBP method could isolate EVs from mouse ULF; the diameter of the isolated EVs was 62±19 nm and expressed CD63, TSG101 and HSP70 proteins. In conclusion, PBP could best preserve the activities of the isolated EVs among the 4 methods studied and was able to isolate EVs from a small volume of sample. The simple setup and low equipment demands makes PBP the most suitable method for rapid EV assessment and isolation of EVs in clinical and basic research settings.
The Paraffin Crystallization in Emulsified Waxy Crude Oil by Dissipative Particle Dynamics

Ruiqiong Wang,Tiantian Du,Jinchen Cao,Guoqiang Wang

DOI: https://doi.org/10.32604/fhmt.2024.047825

IF: 4.397

2024-01-01

Computer Systems Science and Engineering

Abstract:With the advancement of oilfield extraction technology, since oil-water emulsions in waxy crude oil are prone to be deposited on the pipe wall, increasing the difficulty of crude oil extraction. In this paper, the mesoscopic dissipative particle dynamics method is used to study the mechanism of the crystallization and deposition adsorbed on the wall. The results show that in the absence of water molecules, the paraffin molecules near the substrate are deposited on the metallic surface with a horizontal morphology, while the paraffin molecules close to the fluid side are arranged in a vertical column morphology. In the emulsified system, more water molecules will be absorbed on the metallic substrate than paraffin molecules, which obstructed the direct interaction between paraffin molecules and solid surface. Therefore, the addition of water molecules hinders the crystallization of wax near the substrate. Perversely, on the fluid side, water molecules promote the formation of paraffin crystallization. The research in this paper reveals the crystallization mechanism of paraffin wax in oil-water emulsions in the pipeline from the microscopic scale, which provides theoretical support for improving the recovery of wax-containing crude oil and enhancing the transport efficiency.

computer science, theory & methods, hardware & architecture
Epoxy Phase-Change Materials Based on Paraffin Wax Stabilized by Asphaltenes

Svetlana O Ilyina,Anna V Vlasova,Irina Y Gorbunova,Nikolai I Lukashov,Michael L Kerber,Sergey O Ilyin

DOI: https://doi.org/10.3390/polym15153243

2023-07-29

Abstract:The usual problem of meltable phase-change agents is the instability in their form upon heating, which can be solved by placing them into a continuous polymer matrix. Epoxy resin is a suitable medium for dispersing molten agents, but it is necessary to make the obtained droplets stable during the curing of the formed phase-change material. This work shows that molten paraffin wax forms a Pickering emulsion in an epoxy medium and in the presence of asphaltenes extracted from heavy crude oil. Theoretical calculations revealed the complex equilibrium in the epoxy/wax/asphaltene triple system due to their low mutual solubility. Rheological studies showed the viscoplastic behavior of the obtained dispersions at 25 °C, which disappears upon the heating and melting of the paraffin phase. Wax and asphaltenes increased the viscosity of the epoxy medium during its curing but did not inhibit cross-linking or reduce the glass transition temperature of the cured polymer. As a result of curing, it is possible to obtain phase-change materials containing up to 45% paraffin wax that forms a dispersed phase with a size of 0.2-6.5 μm. The small size of dispersed wax can decrease its degree of crystallinity to 13-29% of its original value, reducing the efficiency of the phase-change material.

Paraffin beads can replace mineral oil as an evaporation barrier in PCR.

Phase Change Materials of Paraffin in H-Bn Porous Scaffolds with Enhanced Thermal Conductivity and Form Stability

Surfactant and Oil Formulations for Monodisperse Droplet Emulsion PCR

A Thermosetting Oil For Droplet-Based Real-Time Monitoring Of Digital Pcr And Cell Culture

Dissolvable Polyacrylamide Beads for High-Throughput Droplet DNA Barcoding

Creating biocompatible oil-water interfaces without synthesis: direct interactions between primary amines and carboxylated perfluorocarbon surfactants

Evaporation Phenomenon in Micro Polymerase Chain Reaction (μpcr) System and a Possible Electrowetting Solution

Paraffin /poly(methyl Methacrylate) Blends As Form-Stable Phase Change Materials for Thermal Energy Storage

Inhibiting wax deposition using palm oil additives

Comparison of Methods for Extracting DNA from Formalin-Fixed Paraffin Sections for Nonisotopic PCR

A new method for phenotyping proliferating cell nuclear antigen positive cells using flow cytometry: implications for analysis of the immune response in vivo.

Optimization of on-bead emulsion polymerase chain reaction based on single particle analysis

Improving the phase change properties of paraffin wax by regulating the pore structure and surface properties of silica aerogel

Construction and optimization of an efficient breathing-based isothermal emulsion amplification method

Preparation and mechanism of hyperbranched polymer as paraffin inhibitor and pour point depressant for high waxy crude oil

Elaboration and Characterization of Whey Protein Beads by an Emulsification/Cold Gelation Process: Application for the Protection of Retinol

B-208 Room Temperature Stable PCR Reagents Preparation Using Capillary-Mediated Vitrification Process

Removal of Polymerase Chain Reaction Inhibitors by Electromembrane Extraction

Polymer-based precipitation preserves biological activities of extracellular vesicles from an endometrial cell line

The Paraffin Crystallization in Emulsified Waxy Crude Oil by Dissipative Particle Dynamics

Epoxy Phase-Change Materials Based on Paraffin Wax Stabilized by Asphaltenes