Short-term effects of moderate alcohol consumption on lipid metabolism and energy balance in normal men.

F. Contaldo,E. D'Arrigo,V. Carandente,C. Cortese,A. Coltorti,M. Mancini,M. Taskinen,E. Nikkilä

DOI: https://doi.org/10.1016/0026-0495(89)90257-6

1989-02-01

Abstract:

What problem does this paper attempt to address?

Applicability of core-shell SiO2 microspheres with a high TiO2 loading as stationary phase for HPLC

Dian Wang,Xiang Wan,Jiafei Wang,Debby Mangelings,Qin Xu,Fazhi Xie,Xianhuai Huang,Weihua Li,Han Xuan,Wensheng Zou,Qishu Qu

DOI: https://doi.org/10.1016/j.aca.2023.341527

IF: 6.911

2023-09-01

Analytica Chimica Acta

Abstract:BACKGROUND: Due to its high chemical stability, sufficient rigidity and zwitterionic ion exchange properties, TiO2 can be considered as an alternative stationary phase material to SiO2 for high performance liquid chromatography. TiO2 stationary phase is usually prepared by coating TiO2 onto SiO2 support by sol-gel method. However, in the traditional coating method, in order to overcome the rapid hydrolysis rate of tetrabutyl orthotitanate, only a very low concentration of tetrabutyl orthotitanate can be used, resulting in a low loading of TiO2 on the support.RESULTS: TiO2 core-shell spheres with a good monodispersity were prepared using 0.25 mol L-1 tetrabutyl orthotitanate. The specific surface area, pore volume, pore diameter and TiO2 loading of the TiO2 core-shell spheres were 66 m2 g-1, 0.15 cm3 g-1, 9.8 nm and 57%, respectively. The core-shell spheres were derivatized with n-octadecyltrichlorosilane and then packed into a stainless steel column to test the separation performance for neutral, basic and acidic samples in liquid chromatography. A baseline separation of polyaromatic hydrocarbons was achieved, showing a column efficiency for fluorene of 118075 plates m-1. The prepared stationary phase was also used to separate acidic and basic mixtures, and column efficiencies of 54500 and 25836 plates m-1 were obtained for N,N-dinitroaniline and p-chlorophenol, respectively. The relative standard deviations of the retention times of polyaromatic hydrocarbons for run-to-run, day-to-day and column-to-column repeatability were all below 5.1%.SIGNIFICANCE AND NOVELTY: This work demonstrated that TiO2 can be coated in the pores of the shell of SiO2 core-shell spheres with high TiO2 loading using a high concentration of tetrabutyl orthotitanate as the titania source. The experimental results show that the TiO2 coated core-shell spheres can be a good alternative stationary phase for liquid chromatography.

chemistry, analytical
Controlled Fabrication of Silica@Covalent Triazine Polymer Core-Shell Spheres as a Reversed-Phase/Hydrophilic Interaction Mixed-Mode Chromatographic Stationary Phase

Huiying Zuo,Yun Guo,Wenjie Zhao,Kai Hu,XiaoYu Wang,Lijun He,Shusheng Zhang

DOI: https://doi.org/10.1021/acsami.9b16438

2019-12-11

Abstract:The unique properties of covalent triazine-based organic framework/polymers, including large surface area, hydrophilic-lipophilic-balanced adsorption, and economical preparation, make it a promising candidate as a stationary phase for high-performance liquid chromatography. However, irregular shapes and wide size distributions of such particles hinder column packing, resulting in a low column efficiency or a high back pressure. Herein, we describe the fabrication of SiO2@ covalent triazine-based organic polymer (CTP) core-shell microspheres with a distinct sphere-coating-sphere appearance using aminosilica as the supporting substrate to grow the CTP shell. By adjusting the amount of reactants, the thickness of the CTP shell, which consists of triazine and 1,3,5-triphenylbenzene monomers, was easily controlled. The developed core-shell microspheres were characterized via scanning electron microscopy, energy dispersive X-ray spectroscopy, transmission electron microscopy, solid-state 13C nuclear magnetic resonance analysis, and N2 adsorption experiments. The synergism of the triazine and aromatic moieties on CTP provides the new stationary phase with multiple retention mechanisms, including hydrophobic, π-π, electron donor-acceptor, hydrogen-bonding interactions, and so forth. On the basis of these interactions, successful separation and higher shape selectivity were achieved among several analytes that vary in polarity under both reversed-phase and hydrophilic interaction liquid chromatography conditions. Therefore, SiO2@CTP microspheres combine the advantages of good column packing properties of the uniform monodisperse silica microspheres and the recognition performance of CTP, generating flexible selectivity and application prospect for both hydrophilic and hydrophobic analytes.
Synthesis of Core-Shell Silica Spheres with Tunable Pore Diameters for HPLC

Qishu Qu,Yang Si,Han Xuan,Kehua Zhang,Xiaoming Chen,Yi Ding,Shaojie Feng,Han-Qing Yu

DOI: https://doi.org/10.1016/j.matlet.2017.09.087

IF: 3

2018-01-01

Materials Letters

Abstract:Core-shell silica particles with fibrous shell structure and tunable pore size were prepared by using a dultemplate method. The pore size of the core-shell silica particles was affected greatly by the amount of octadecylamine, which as used as cosurfactant. The pore size could be enlarged from 7.1 nm to 22.3 nm while keeping the unique fibrous shell structure. After derivatized with C18, the separation performances of these particles with a wider pore size were investigated. The column efficiency was as high as 219,789 plates m (1) for dimethylnaphthalene. Baseline separation of proteins ranging in size from 12 to 66 kD was achieved within 5 min. The separation results demonstrate that the synthesized core-shell silica particles would be a promising packing material in the rapid and high-resolution separation of both small solutes and macromolecules. (C) 2017 Elsevier B.V. All rights reserved.
Synthesis of Titania-Silica Core-Shell Microspheres Via A Controlled Interface Reaction in A Microfluidic Device

Wenjie Lan,Shaowei Li,Jianhong Xu,Guangsheng Luo

DOI: https://doi.org/10.1021/la202055f

IF: 3.9

2011-01-01

Langmuir

Abstract:In this work, we describe a novel, simple microfluidic method for fabricating titania-silica core-shell microspheres. Uniform droplets of silica sol were dispersed into an oil phase containing tetrabutyl titanate via a coaxial microfluidic device. The titanium alkoxide hydrolyzed at the water-oil interface after the formation of the aqueous droplets. A gel shell containing the titanium hydroxide formed around the droplets, and the titania-silica core-shell microspheres were obtained after calcinations. The X-ray diffraction results show that titania coatings crystallized into a pure anatase structure. The scanning electron microscopy and energy-dispersive spectrometry characterization shows that the microspheres are monodispersed with uniform titania coating on the surface. The dispersity and size of the microspheres could easily be controlled by changing the microfluidic flow parameters. The titania content on the surface could be adjusted in the large range of 1.0-98.0 mol % by varying the continuous phase composition and the reaction time, and the structures of the core-shell microshperes could also be controlled.
A Nanocrystalline Metal Organic Framework Confined in the Fibrous Pores of Core-Shell Silica Particles for Improved HPLC Separation

Qishu Qu,Yang Si,Han Xuan,Kehua Zhang,Xiaoming Chen,Yi Ding,Shaojie Feng,Han-Qing Yu

DOI: https://doi.org/10.1007/s00604-017-2439-1

IF: 5.7

2017-01-01

Microchimica Acta

Abstract:A hybrid material was prepared from a metal-organic framework (MOF) and core-shell silica by using a kinetic controlling approach. The nanocrystalline MOF (HKUST-1) was prepared from 1,3,5-benzenetricarboxylate and copper(II) by tuning the reaction rate via the fraction of ethanol in the solvent. After the reaction rate was reduced to a certain degree, the pore surface would be well covered with Cu(II), which initiated the formation of a nanocrystalline HKUST-1. The resulting hybrid material was packed into a stainless-steel column (4.6 × 150 mm) and used as a stationary phase in high performance liquid chromatography. SiO2@dSiO2-HKUST-1 combined the merits of the high separation performance of the core-shell particles and the unique selectivity of the HKUST-1 nanocrystals. A separation efficiency as high as almost 140,000 plates per meter was achieved for the model analyte styrene. The material was stable and exhibited a highly reproductivity. The relative standard deviations of column-to-column, intra-day, and inter-day reproducibility of the SiO2@dSiO2-HKUST-1 packed columns for the retention time of styrene were 4.7%, 0.3%, and 0.4%, respectively.
Porous Organic Cage-Embedded C10-Modified Silica as HPLC Stationary Phase and Its Multiple Separation Functions

Litao Wang,Siqi Han,Haiyang Yu,Qinghua Yu,Dong Pei,Wenjing Lv,Jiasheng Wang,Xingyu Li,Ruifang Ding,Qibao Wang,Mei Lv

DOI: https://doi.org/10.3390/molecules27248895

IF: 4.6

2022-12-14

Molecules

Abstract:Reduced imine cage (RCC3) was covalently bonded to the surface of silica spheres, and then the secondary amine group of the molecular cage was embedded in non-polar C10 for modification to prepare a novel RCC3-C10@silica HPLC stationary phase with multiple separation functions. Through infrared spectroscopy, thermogravimetric analysis and nitrogen adsorption–desorption characterization, it was confirmed that RCC3-C10 was successfully bonded to the surface of silica spheres. The resolution of RCC3-C10@silica in reversed-phase separation mode is as high as 2.95, 3.73, 3.27 and 4.09 for p-phenethyl alcohol, 1-phenyl-2-propanol, p-methylphenethyl alcohol and 1-phenyl-1-propanol, indicating that the stationary phase has excellent chiral resolution performance. In reversed-phase and hydrophilic separation modes, RCC3-C10@silica realized the separation and analysis of a total of 70 compounds in 8 classes of Tanaka mixtures, alkylbenzene rings, polyphenyl rings, phenols, anilines, sulfonamides, nucleosides and flavonoids, and the analysis of a variety of chiral and achiral complex mixtures have been completed at the same time. Compared with the traditional C18 commercial column, RCC3-C10@silica exhibits better chromatographic separation selectivity, aromatic selectivity and polar selectivity. The multifunctional separation mechanism exhibited by the stationary phase originates from various synergistic effects such as hydrophobic interaction, π-π interaction, hydrogen bonding and steric interaction provided by RCC3 and C10 groups. This work provides flexible selectivity and application prospects for novel multi-separation functional chromatographic columns.

chemistry, multidisciplinary,biochemistry & molecular biology
Preparation of core–shell silica particles with tunable pore size by phenylethanol as swelling agent for chromatographic separation

Bei Liu,Yali Yang,Kaijun Quan,Jia Chen,Haixia Zhang,Hongdeng Qiu

DOI: https://doi.org/10.1016/j.matlet.2024.136343

IF: 3

2024-06-01

Materials Letters

Abstract:The core–shell particles with tunable pore size were synthesized by a bi-phase reaction successfully. By adjusting the amount of phenylethanol, fibrous shells with tunable pore sizes ranging from 4 to 19 nm could be obtained in one pot. The obtained silica microspheres were used for chromatographic separation after modification with octyltrichlorosilane and end-capping with N-(trimethoxysilylpropyl)imidazole. Better resolutions of nitroimidazoles and anilines were obtained on the end-capped stationary phase. This particle could serve as an HPLC stationary phase with good reproducibility and particular selectivity.

materials science, multidisciplinary,physics, applied
PREPARATION OF NANO TiO2 ON SURFACE OF SILICA

王挺,蒋新

DOI: https://doi.org/10.3321/j.issn:0438-1157.2003.12.023

2003-01-01

Abstract:TiO 2 nanoparticles were in-situ prepared on the solid/liquid interfacial adsorption layer. In the suspension of colloidal silica particles in binary mixtures of water/ethanol, a water-rich layer was formed on the hydrophilic surface of SiO 2. After phase equilibrium, dropping tetrabutyl titanate diffused into the adsorption layer and reacted with water. After centrifugation and drying, samples were obtained. The solvent-substituted experiment testified that reaction took place on the adsorption layer. TEM, XRD and electronic energy spectrum indicated uniform TiO 2 laid over the surface of SiO 2 particles. The effect of reaction temperature was investigated and potential mechanism was discussed.
Synthesis of hierarchically porous zirconium-based metal-organic framework@silica core-shell stationary phase through etching strategy for liquid chromatography

Habib Ur Rehman,Chunyan Zhang,Xiangwei Liu,Yang Liu,Jiawei Liu,Changwei Tang,Quan Bai

DOI: https://doi.org/10.1016/j.chroma.2023.464377

IF: 4.601

2023-09-14

Journal of Chromatography A

Abstract:Metal organic frameworks (MOFs) show promise to be employed as stationary phase for high performance liquid chromatography (HPLC), however, the microporous structures of MOFs seriously restrict the diffusion and mass transfer of solute molecules, leading to a low column efficiency. In this paper, the fabrication of hierarchically porous UiO-66@SiO 2 (HP- UiO-66@SiO 2 ) core-shell microspheres via H 2 O 2 etching has been proposed as a viable approach to enhance the separation performance of MOFs-based columns for HPLC. Through the direct treatment of the preliminary prepared UiO-66@SiO 2 microspheres with H 2 O 2 etching, HP-UiO-66@SiO 2 core-shell microspheres were successfully synthesized with an enlarged pore size of up to 9 nm, facilitating efficient mass transfer in chromatographic separation. The prepared HP-UiO-66@SiO 2 core-shell microspheres were then explored as stationary phase in HPLC to separate the nonpolar alkyl benzene homologues, the polar aromatic alcohol homologues and the xylene isomers. The results indicated that the baseline separations of these solutes were achieved successfully with narrow peak width and higher resolution than the UiO-66@SiO 2 column. The HP-UiO-66@SiO 2 column exhibited superior separation performance, reaching a maximum plate number of 134459/m for fluorene, and showing good reproducibility. As a result, this template-free approach suggests that the fabrication of hierarchically porous MOFs@silica core-shell microspheres is a successful approach to enhance the column efficiency of MOFs-based columns in HPLC.

chemistry, analytical,biochemical research methods
Controllable and Repeatable Synthesis of Thermally Stable Anatase Nanocrystal-Silica Composites with Highly Ordered Hexagonal Mesostructures.

Weiyang Dong,Yaojun Sun,Chul Wee Lee,Weiming Hua,Xinchun Lu,Yifeng Shi,Shicheng Zhang,Jianmin Chen,Dongyuan Zhao

DOI: https://doi.org/10.1021/ja073804o

IF: 15

2007-01-01

Journal of the American Chemical Society

Abstract:In this article, we report a controllable and reproducible approach to prepare highly ordered 2-D hexagonal mesoporous crystalline TiO2-SiO2 nanocomposites with variable Ti/Si ratios (0 to infinity). XRD, TEM, and N2 sorption techniques have been used to systematically investigate the pore wall structure, and thermal stability functioned with the synthetic conditions. The resultant materials are ultra highly stable (over 900 degrees C), have large uniform pore diameters (approximately 6.8 nm), and have high Brunauer-Emmett-Teller specific surface areas (approximately 290 m2/g). These mesostructured TiO2-SiO2 composites were obtained using titanium isopropoxide (TIPO) and tetraethyl orthosilicate (TEOS) as precursors and triblock copolymer P123 as a template based on the solvent evaporation-induced co-self-assembly process under a large amount of HCl. Our strategy was the synchronous assembly of titanate and silicate oligomers with triblock copolymer P123 by finely tuning the relative humidity of the surrounding atmosphere and evaporation temperature according to the Ti/Si ratio. We added a large amount of acidity to lower condensation and polymerization rates of TIPO and accelerate the rates for TEOS molecules. TEM and XRD measurements clearly show that the titania is made of highly crystalline anatase nanoparticles, which are uniformly embedded in the pore walls to form the "bricked-mortar" frameworks. The amorphous silica acts as a glue linking the TiO2 nanocrystals and improves the thermal stability. As the silica contents increase, the thermal stability of the resulting mesoporous TiO2-SiO2 nanocomposites increases and the size of anatase nanocrystals decreases. Our results show that the unique composite frameworks make the mesostructures overwhelmingly stable; even with high Ti/Si ratios (> or =80/20) the stability of the composites is higher than 900 degrees C. The mesoporous TiO2-SiO2 nanocomposites exhibit excellent photocatalytic activities (which are higher than that for commercial catalyst P25) for the degradation of rhodamine B in aqueous suspension. The excellent photocatalytic activities are ascribed to the bifunctional effect of highly crystallized anatase nanoparticles and high porosity.
Mesoporous TiO2 Microspheres with Precisely Controlled Crystallites and Architectures

Kun Lan,Ruicong Wang,Wei Zhang,Zaiwang Zhao,Ahmed Elzatahry,Xingmiao Zhang,Yao Liu,Dhaifallah Al-Dhayan,Yongyao Xia,Dongyuan Zhao

DOI: https://doi.org/10.1016/j.chempr.2018.08.008

IF: 23.5

2018-01-01

Chem

Abstract:Mesoporous TiO2 nanomaterials have been investigated for decades; however, most endeavors have been focused on the exploration of their potentials in various applications, and the fundamental research for preparing mesoporous TiO2 in a highly controllable manner remains unfruitful. Herein, we report a facile pressure-driven oriented assembly approach to synthesize an unprecedented type of dehiscent mesoporous TiO2 microspheres with radial mesopore channels and oriented rutile crystallites. By varying the concentrated HCl amount, we have been able to produce TiO2 microspheres with well-controlled rutile/anatase phase ratio. By further manipulating the reaction conditions including solvent evaporation time and hydrothermal temperature, the oriented growth with tunable crevices can also be well manipulated. Such dehiscent mesoporous TiO2 microspheres have exhibited great permeability and excellent photocatalytic properties for H2 generation. We believe that the high structural complexity and predictability of this method offers great opportunities in enhancing the performance of TiO2-based materials.
Core-shell metal-organic framework/silica hybrid with tunable shell structure as stationary phase for high performance liquid chromatography

Jiafei Wang,Yuqing He,Xiang Wan,Fazhi Xie,Yuanshe Sun,Tong Li,Qin Xu,Donglin Zhao,Qishu Qu

DOI: https://doi.org/10.1016/j.chroma.2023.464164

IF: 4.601

2023-06-20

Journal of Chromatography A

Abstract:Metal-organic framework/silica composite (SSU) were prepared by growing UiO-66 on the amino-functionalized SiO 2 core-shell spheres (SiO 2 @ d SiO 2 ) via a simple one-pot synthesis approach. By controlling the concentration of Zr 4+ , the obtained SSU have two different morphologies: spheres-on-sphere and layer-on-sphere. The spheres-on-sphere structure is formed by the aggregation of UiO-66 nanocrystals on the surface of SiO 2 @ d SiO 2 spheres. SSU-5 and SSU-20, which contain spheres-on-sphere composites have mesopores with a pore size of about 45 nm in addition to the characteristic micropores of UiO-66 with a pore size of 1 nm. In addition, UiO-66 nanocrystals were grown both inside and outside the pores of SiO 2 @ d SiO 2 , resulting in a 27% loading of UiO-66 in the SSU. The layer-on-sphere is the surface of SiO 2 @ d SiO 2 covered with a layer of UiO-66 nanocrystals. SSU with this structure has only a characteristic pore size of about 1 nm belonging to UiO-66 and is therefore not suitable as a packed stationary phase for high performance liquid chromatography. The SSU spheres were packed into columns and tested for the separation of xylene isomers, aromatics, biomolecules, acidic and basic analytes. With both micropores and mesopores, SSU with spheres-on-sphere structure achieved baseline separation of both small and large molecules. Efficiencies up to 48150, 50452 and 41318 plates m −1 were achieved for m -xylene, p -xylene and o -xylene, respectively. The relative standard deviations of the retention times of anilines for run-to-run, day-to-day and column-to-column were all less than 6.1%. The results show that the SSU with spheres-on-sphere structure has great potential for high performance chromatographic separation.

chemistry, analytical,biochemical research methods
High performance separation of aerosol sprayed mesoporous TiO2 sub-microspheres from aggregates via density gradient centrifugation

Yichi Zhang,Yifeng Shi,Ya-Hsuan Liou,April M. Sawvel,Xiaohong Sun,Yue Cai,Patricia A. Holden,Galen D. Stucky

DOI: https://doi.org/10.1039/b926183d

2010-01-01

Journal of Materials Chemistry

Abstract:Mesoporous titanium dioxide sub-microspheres were prepared using aerosol techniques with a size distribution from 80 nm to 3 mu m. Both theoretical and experimental results showed that non-equilibrium sucrose density gradient centrifugation is an effective way to size-partition these titanium dioxide nanoparticles from a continuous and broad particle size range. The sucrose serves as a multifunctional solution and plays three significant roles during the metal oxide fractionation. First, the high viscosity and density make the sedimentation rate of nanomaterials sensitive to particle size, which leads to particle fractionation in solution. Second, sucrose greatly decreases aggregation among nanoparticles during the separation by acting as a non-ionic capping agent. No other capping agent or surfactant is required. Finally, the density gradient stratifies the nanoparticles with a similar size into well-defined layers, so that the size-selected particles are relatively easy to collect. In addition, the unique biocompatibility of sucrose makes this fractionation method an ideal candidate for biological applications of nanoparticles. Post-aerosol synthesis separation of mesoporous metal oxide nanoparticles using a non-equilibrium density gradient has proven to be an effective, scalable way to access a large fraction of TiO2 sub-microspheres within a narrow size range and a low polydispersity index.
Preparation of carboxyl‐functionalized silica core‐shell microspheres and their applications in weak cation exchange chromatography, heavy metal removal, and lysozyme enrichment

Shadi Ali Hassen Ahmed,Bassam Saif,Qian LingHui

DOI: https://doi.org/10.1002/jssc.202400126

IF: 3.614

2024-06-01

Journal of Separation Science

Abstract:Chromatography is a technique of separation based on adsorption and/or interaction of target molecules with stationary phases. Herein, we report the design and fabrication of BTDA@SiO2 core‐shell microspheres as a new class of stationary phase and demonstrate its impressive performance for chromatographic separations. The silica microspheres of BTDA@SiO2 were synthesized by in situ method with 1,3,5‐benzenetricarboxaldehyde and 3,5‐diaminobenzoic to separate peptides and proteins on high‐performance liquid chromatography. The BTDA@SiO2 core‐shell structure has a high specific surface area and retention factor of 4.27 and 8.31 for anionic and cationic peptides, respectively. The separation factor and resolution were high as well. A typical chromatogram illustrated nearly baseline resolution of the two peptides in less than 3 min. The BTDA@SiO2 was also highly stable in the pH range of 1 to 14. Furthermore, the prepared BTDA@SiO2 core‐shell material not only be used for chromatographic separation but also as heavy metal removal from water. Using a BTDA@SiO2, we also achieved a lysozyme enrichment with a maximum saturated adsorption capacity reaching 714 mg/g. In summary, BTDA@SiO2 has great application prospects and significance in separation and purification systems.

chemistry, analytical
A composite hydrogel modified silica stationary phase for mixed‐mode liquid chromatography

Tong Zhang,Shuai Wang,Xiaofeng Lu,Yong Guo,Xiaojing Liang

DOI: https://doi.org/10.1016/j.chroma.2023.464300

IF: 4.601

2023-08-16

Journal of Chromatography A

Abstract:A novel composite hydrogel functionalized silica core-shell stationary phase was prepared by the surface modification of silica sphere. The successful synthesis of the new stationary phase (T-Sil@PAM/SA/UiO-66-NH 2 ) was proven by scanning electron microscope (SEM), transmission electron microscope (TEM), X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD), etc. Due to the coexistence of amide, hydroxyl, long carbon chain and UiO-66-NH 2 in composite hydrogel shell, the obtained stationary phase can be used in hydrophilic/reversed-phase liquid chromatography with multiple retention mechanisms, such as hydrophilic, hydrophobic and π - π interactions. The chromatographic retention behavior of T-Sil@PAM/SA/UiO-66-NH 2 demonstrated that the new stationary phase showed excellent separation performance for both polar analytes (such as alkaloids, saccharides, etc.) and nonpolar analytes (such as substituted benzene and polycyclic aromatic hydrocarbon (PAHs), etc.). Furthermore, compared with NH 2 column and commercial C18 column, the T-Sil@PAM/SA/UiO-66-NH 2 exhibited a certain superiority. Moreover, the relative standard deviation (RSD) of PAHs' retention time with eight replicates consecutive elution was found to range from 0.03% to 0.17%. Therefore, the successful use of T-Sil@PAM/SA/UiO-66-NH 2 in mixed‐mode liquid chromatography expanded the potential applications of hydrogels in the field of separation.

chemistry, analytical,biochemical research methods
Thrombus deformation of inferior vena caval filter.

M. Marx,S. Meyer,U. Malhotra

DOI: https://doi.org/10.2214/AJR.164.3.7863923

1995-03-01

Abstract:
Size- And Density-Controlled Synthesis Of Tio2 Nanodots On A Substrate By Phase-Separation-Induced Self-Assembly

Ming Luo,Kui Cheng,Wenjian Weng,Chenlu Song,Piyi Du,Ge Shen,Gang Xu,Gaorong Han

DOI: https://doi.org/10.1088/0957-4484/20/21/215605

IF: 3.5

2009-01-01

Nanotechnology

Abstract:This work presents a facile way, i.e. phase-separation-induced self-assembly, to prepare TiO2 nanodots on a substrate. This method induces convective flow in a spin-coated titanium tetrabutoxide (TBOT)/polyvinyl pyrrolidone (PVP)/ethanol liquid film through the Marangoni effect and turns TBOT into crystalline TiO2 nanodots on a substrate after calcination. The size and density of the TiO2 nanodots can be finely tailored by controlling the concentrations of TBOT and PVP in the precursor sol. The TiO2 nanodot-deposited surface showed a hydrophilic characteristic and the wettability was obviously improved by increasing nanodot size.
Confined Interfacial Monomicelle Assembly for Precisely Controlled Coating of Single-Layered Titania Mesopores

Kun Lan,Yuan Xia,Ruicong Wang,Zaiwang Zhao,Wei Zhang,Xingmiao Zhang,Ahmed Elzatahry,Dongyuan Zhao

DOI: https://doi.org/10.1016/j.matt.2019.03.003

IF: 18.9

2019-01-01

Matter

Abstract:Mesoporous core-shell nanostructures have recently been receiving extensive scientific interest; however, reliable approaches for coating mesoporous materials still remain exciting challenges, except for amorphous silica. We report, for the first time, a confined interfacial monomicelle assembly method for controlled coating of anatase TiO2 with single-layered ordered mesopores on diverse surfaces, opening up the area of coating ordered mesoporous crystalline materials that possess mesopores originating from self-assembled surfactant instead of accumulated nanocrystals. This facile and repeatable methodology relies on the solvent-confinement effect of glycerol during the assembly process and monomicelle hydrogel preformation by selective evaporation of double-solvent precursors. This assembly process shows precise controllability and great versatility, endowing the coated TiO2 layers with highly tunable thickness, mesopore size, and switchable coated surfaces. The ultrathin monolayered mesopores of such mesoporous TiO2 shells, in combination with their high surface area and highly crystalline nature, afford them excellent rate capability and superior cyclability for sodium-ion storage.
Synthesis of Highly Dispersed Mesostructured Cellular Foam Silica Sphere and Its Application in High-Performance Liquid Chromatography

Sha Chen,Xiaoqiong Zhang,Qiang Han,Ming Yu Ding

DOI: https://doi.org/10.1016/j.talanta.2012.09.047

IF: 6.1

2012-01-01

Talanta

Abstract:Highly dispersed mesostructured cellular foam silica spheres of relatively uniform micrometer size (3.5-4.5 μm) were successfully prepared using a triblock copolymer EO(20)PO(70)EO(20) as the structure-directing agent accompanied by TMB and K(2)SO(4). Both two additives have effective influence and K(2)SO(4) have better performance than other inorganic salts such as KCl and NaCl. The pore size and surface area were tuned by TMB and NH(4)F. The resultant S-MCFs were modified with C(18) group before being used as the HPLC stationary phase for effective separation of aromatic compounds and phthalic acid esters. The perfect spherical morphology and large pore volume gave rise to low and stable back pressure. High surface area, ultralarge pore size and unique pore structure would permit high flow rates and afford the possibility for fast separation.
Synthesis of Core-Shell Nanostructured SiO2/TiO2 Photocatalysts Via Atomic Layer Deposition in a Fluidized Bed with Central Tube

Wei Liu,Daoyin Liu,Zuyang Zhang,Zhenkun Sun

DOI: https://doi.org/10.1016/j.partic.2023.12.015

IF: 3.5

2024-01-01

Particuology

Abstract:Fluidized bed atomic layer deposition is an efficient technique for particle coating with precise control over the film thickness and uniformity at the sub-nanoscale. In this study, a fluidized bed with a central tube is designed, where the central tube has two roles: improve fluidization and deliver precursors separately. The synthesis of core-shell structured SiO2/TiO2 nanoparticle catalysts for photodegradation of tetracycline hydrochloride (TC) is carried out using TiCl4 and H2O as precursors at 180 degrees C under atmospheric pressure. Under the combination of vibration and central tube, the segregation of agglomerate size along the bed height is weakened, and the prepared SiO2/TiO2 nanoparticles show excellent photocatalytic degradation performance: the degradation efficiency on TC is 96% under 300 W xenon lamp irradiation for 60 min. The mechanism of enhanced photocatalytic activity is due to the Ti-O-Si bonds generated at the interface, which increase the ability to absorb sunlight and accelerate the separation of holes and electrons. (c) 2024 Chinese Society of Particuology and Institute of Process Engineering, Chinese Academy of Sciences. Published by Elsevier B.V. All rights reserved.

Short-term effects of moderate alcohol consumption on lipid metabolism and energy balance in normal men.

Applicability of core-shell SiO2 microspheres with a high TiO2 loading as stationary phase for HPLC

Controlled Fabrication of Silica@Covalent Triazine Polymer Core-Shell Spheres as a Reversed-Phase/Hydrophilic Interaction Mixed-Mode Chromatographic Stationary Phase

Synthesis of Core-Shell Silica Spheres with Tunable Pore Diameters for HPLC

Synthesis of Titania-Silica Core-Shell Microspheres Via A Controlled Interface Reaction in A Microfluidic Device

A Nanocrystalline Metal Organic Framework Confined in the Fibrous Pores of Core-Shell Silica Particles for Improved HPLC Separation

Porous Organic Cage-Embedded C10-Modified Silica as HPLC Stationary Phase and Its Multiple Separation Functions

Preparation of core–shell silica particles with tunable pore size by phenylethanol as swelling agent for chromatographic separation

PREPARATION OF NANO TiO2 ON SURFACE OF SILICA

Synthesis of hierarchically porous zirconium-based metal-organic framework@silica core-shell stationary phase through etching strategy for liquid chromatography

Controllable and Repeatable Synthesis of Thermally Stable Anatase Nanocrystal-Silica Composites with Highly Ordered Hexagonal Mesostructures.

Mesoporous TiO2 Microspheres with Precisely Controlled Crystallites and Architectures

Core-shell metal-organic framework/silica hybrid with tunable shell structure as stationary phase for high performance liquid chromatography

High performance separation of aerosol sprayed mesoporous TiO2 sub-microspheres from aggregates via density gradient centrifugation

Preparation of carboxyl‐functionalized silica core‐shell microspheres and their applications in weak cation exchange chromatography, heavy metal removal, and lysozyme enrichment

A composite hydrogel modified silica stationary phase for mixed‐mode liquid chromatography

Thrombus deformation of inferior vena caval filter.

Size- And Density-Controlled Synthesis Of Tio2 Nanodots On A Substrate By Phase-Separation-Induced Self-Assembly

Confined Interfacial Monomicelle Assembly for Precisely Controlled Coating of Single-Layered Titania Mesopores

Synthesis of Highly Dispersed Mesostructured Cellular Foam Silica Sphere and Its Application in High-Performance Liquid Chromatography

Synthesis of Core-Shell Nanostructured SiO2/TiO2 Photocatalysts Via Atomic Layer Deposition in a Fluidized Bed with Central Tube