Abstract:In recent years, the rapidly growing consumption of fossil fuels negatively affects the environment and public health has attracted much attention. Much effort has been made to find a clean and renewable alternative energy. Bio-oil, produced by flash pyrolysis, is one of the more encouraging products for valorisation of biomass. It has been identified as a promising alternative energy source for fossil fuel owing to its outstanding characteristics such as higher energy density, more suitable for storage and transportation, less capital investment than any other products of biomass. However, the nature of bio-oil contains high acidity, strong corrosiveness, low heating value, thermal instability and chemical complexity, which severely restrict its wide range of applications as a high quality energy. Therefore, it is necessary to upgrade bio-oil. The upgrading techniques include steam reforming, esterification, emulsification, hydrodeoxygenation, catalytic pyrolysis etc. In this paper, catalytic pyrolysis experiments were performed in a fixed bed with inner diameter of 16mm and height of 380mm for bio-oil model compounds (diacetone alcohol, furfural, ethyl acetate and guaiacol) over different characteristics zeolites (HY, HZSM-5, ZSM-5, P/ZSM-5, La/ZSM-5, Ni/ZSM-5) at the condition of T=400℃, WHSV=4 h-1. The catalysts physical properties were investigated by BET (Brunauer-Emmett-Teller surface area) analyse. Water content was detected by using the method of Karl Fischer (870 KF Titrino). The GC-MS was used to analyze the major constituents of the pyrolytic products qualitatively and quantitatively. After the addition of La, the pore size increased from 0.61 nm (ZSM-5) to 0.89 nm (La-ZSM-5). On the contrary, the pore size of P modified ZSM-5 is 0.49 nm which is smaller than that of ZSM-5. The pyrolytic products of the model compounds included organic fraction, water, coke and gas. Compared with ZSM-5,the coke deposition over the La modified ZSM-5 decreased from 2.61% to 1.99% and the organic fraction increased dramatically from 46.10% to 61.51%, which showed the best performance in terms of products distribution among all modified catalyst. The conversions of overall model components and single model component were calculated respectively. The difficulty of the model components pyrolysis is guaiacol>furfural>ethyl acetate>diacetone alcohol. By adding catalysts, the conversion of totally compounds were increased in different degrees, which meaned zeolite promoted the degree of catalytic pyrolysis. HZSM-5 had a best catalytic pyrolysis activity with the highest totally compounds conversion rate of 65.98%. There was a slight decline in the conversion of model compounds contrasted ZSM-5 with La/P/Ni modified ZSM-5. The major components of catalytic pyrolysis were aromatic hydrocarbons, ketones, phenols and so on. It means that a series of decarboxylation and decarbonylation reactions were taken place during the pyrolysis process. On the one hand, the reduction of the oxygen content of bio-oil help to improve its stability, on the other hand it will enhance its heating value. The optimal selectivity of aromatic reached 7.36% over HZSM-5. The La modified ZSM-5 improved the selectivity of aromatic from 6.72%to 7.28%. The highest yield of saturated alcohol was 7.1%over ZSM-5 and decreased using modified ZSM-5. According to the catalytic pyrolysis products distribution, the different reaction pathways for model compounds were discussed, which provided a theoretical basis for experimental study of upgrading bio-oil.

Red-mud based porous nanocatalysts for valorisation of municipal solid waste

Co-pyrolysis of biomass with Red Mud: An efficient approach to improving bio-oil quality and resourceful utilization of the iron in Red Mud

Red Mud as a Potential Catalyst for Petrochemicals Production from Oxygenated Aromatic Plastic Wastes via Fast Pyrolysis

Ex-situ catalytic co-pyrolysis of sawdust and municipal solid waste based on multilamellar MFI nanosheets to obtain hydrocarbon-rich bio-oil

Utilization of red mud as catalyst in conversion of waste oil and waste plastics to fuel

Boosting production of useful chemicals and micro-mesopores biochar from in situ catalytic pyrolysis of cellulose with red mud

Catalytic pyrolysis of bio-oil model compounds over La/P/Ni modified ZSM-5

Effect and mechanisms of red mud catalyst on pyrolysis remediation of heavy hydrocarbons in weathered petroleum-contaminated soil

Co-hydropyrolysis of Pine and HDPE over Bimetallic Catalysts: Efficient BTEX Production and Process Mechanism Analysis

Improving Fuel Properties and Hydrocarbon Content from Residual Fat Pyrolysis Vapors over Activated Red Mud Pellets in Two-Stage Reactor: Optimization of Reaction Time and Catalyst Content

Study on the mechanism and reaction characteristics of red-mud-catalyzed pyrolysis of corn stover

Enhanced pyrolysis of palm kernel shell wastes to bio-based chemicals and syngas using red mud as an additive

Waste utilization of sewage sludge and red mud based on chemical looping catalytic oxidation

Direct synthesis of Fe-aluminosilicates from red mud for catalytic deoxygenation of waste cooking oil

Influence of red mud as a catalyst in the thermocatalytic reforming process

In-situ catalytic upgrading of coal pyrolysis volatiles over red mud-supported nickel catalysts

Biomass:polystyrene co-pyrolysis coupled with metal-modified zeolite catalysis for liquid fuel and chemical production

Catalytic co-pyrolysis of solid wastes (low-density polyethylene and lignocellulosic biomass) over microwave assisted biochar for bio-oil upgrading and hydrogen production

Synergistic optimization of bio–oil quality and heavy metal solidification during microwave co–pyrolysis of cow dung and red mud

Synergistic Promotion for CO2 Absorption and Solvent Regeneration by Fine Waste Red Mud Particles on in Amine-Based Carbon Capture: Performance and Mechanism

Kinetic research of red mud waste oxidative pyrolysis and comparison under different atmospheres