Abstract:Owing to their superior mechanical properties of high hardness, wear resistance, and corrosion resistance, CoCrFeNiTi high entropy alloys (HEAs) attracted the attention of researchers to use as coating materials for titanium (Ti) and its alloys. Directed energy deposition (DED) has the potential to combine both the fabrication process and the laser remelting process (implemented by double laser scanning) using the same equipment set-up. With high energy density and rapid cooling rate, combining DED and laser remelting is considered an effective method to enhance solid solution strengthening effects and element segregation of CoCrFeNiTi HEA coatings, thus being able to affect HEA coatings' phase constitutions, microstructure, and mechanical properties. To date, there are no reported publications on the deposition of CoCrFeNiTi HEA coatings via the combination of DED and laser remelting process. In addition, the investigation of the effects of remelting laser power is still lacking. To fill these gaps, the relationships among the levels of remelting laser power, molten pool properties, microstructure, and mechanical properties of CoCrFeNiTi HEA coatings are built by DED with the laser remelting process in this investigation. When the remelting laser power is higher than 225 W (75 % of the laser power in the DED process), the three-phase microstructure changes to a two-phase microstructure. The higher molten pool temperature, lower cooling rate, and secondary solidification induced by a relatively high remelting laser power can enhance the solid solution strengthening effects and promote the precipitation of the high-hardness Χ phase and Laves phase. After the 300 W laser remelting process, the highest average microhardness of the coatings is obtained as 916 HV 1.0 , which is 65 % higher than that of the coatings without laser remelting process. The best wear resistance is observed in the coatings with 225 W remelting laser power instead of 300 W remelting laser power since the high content of brittle phase caused by high remelting laser power could promote the formation of abrasive particles during the dry sliding tests.

Microstructure and Tribological Properties of AlCoCrFeNi2.1 Dual-Phase High-Entropy Alloy Enhanced by Laser Remelting

Effect of Process Parameters on Microstructure and Properties of AlCoCrFeNi-WC-WS2 Composite Coating Prepared by Laser Cladding

Enhanced Surface Properties of the Al0.65CoCrFeNi High-Entropy Alloy via Laser Remelting

Influences of Laser Surface Melting on Microstructure, Mechanical Properties and Corrosion Resistance of Dual-Phase Cr–Fe–Co–Ni–Al High Entropy Alloys

Laser remelting of CoCrFeNiTi high entropy alloy coatings fabricated by directed energy deposition: Effects of remelting laser power

Effects of Laser Powers on Microstructures and Mechanical Properties of Al0.5FeCoCrNi High-Entropy Alloys Fabricated by Laser Melting Deposition

Effect of laser energy densities on the phase composition change in laser-cladded AlCoCrNbMo high-entropy alloy coatings

Microstructure evolution and mechanical properties of Al CoCrFeNi high-entropy alloys by laser melting deposition

Effect of Laser Parameters on the Microstructure and Properties of CoCrFeNiMn High Entropy Alloy Coatings

Effect of phase transformation on mechanical properties of Al16.80Co20.74Cr20.49Fe21.28Ni20.70 high entropy alloy coatings processed by laser cladding

Research on the Mechanical Properties of AlCoCrFeNi + CoCrNi Fabricated by Laser Melting Deposition

Tailoring the surface microstructures and enhancing wear performance of Al0.5CoCrFeNiSi0.25 high-entropy alloys via laser remelting

Tribology behavior in laser cladded dual-phase Al x CoCrFeNiMn (1-x) high entropy alloys influenced by hierarchical interface architecture

Effects of laser remelting on microstructure and tribological properties of plasma–sprayed Fe45Mn35Co10Cr10 high–entropy alloy coating

Surface modification for AlCoCrFeNi2.1 eutectic high-entropy alloy via laser remelting technology and subsequent aging heat treatment

Formation and beneficial effects of the amorphous/nanocrystalline phase in laser remelted (FeCoCrNi)75Nb10B8Si7 high-entropy alloy coatings fabricated by plasma cladding

Microstructure and properties analysis of FeCoNiAlCu dual-phase high-entropy alloy coating by laser cladding

Research on the laser melting coating process of an AlCoCrFeNi high‐entropy alloy

Microstructure Evolution and Enhanced Wear Resistance of Al2CrFeNiMo High Entropy Alloy Coating Fabricated by Laser Cladding

Surface hardening of CrCoFeNi high-entropy alloys via Al laser alloying

Microstructural Evolution and Mechanical Properties of Laser Beam Welded AlxCoCrFeNi High Entropy Alloys