Abstract:Several ASTM standards on the fracture of glued and welded joints need attention because they do not consider the Griffith energy criterion of cracking which was proposed a century ago. It is almost as if Griffith never existed because the ASTM definition of failure is the stress criterion postulated by Galileo in 1638 in which stress at failure (i.e. strength = force/area) is defined as the determinant of fracture. Irene Martinez Villegas (Villegas, Rans 2021 Phil. Trans. R. Soc. A 376, 20200296. ( doi:10.1098/rsta.2020.0296 )) shows in this volume that attempts to use ASTM D5868 to standardize welded composite (carbon fibre reinforced polymer, CFRP) lap joints reveal major problems. First, the test is a low angle bend–peel test; not shear. Second, the energy required to break the joint is not emphasized so that joints may have high strength properties but also low toughness; third, the fracture force is not proportional to the lap joint area so the concept of strength independent of sample size is false; fourth, as the CFRP panels are made thicker, the strength rises at constant overlap area so the strength can be any value you want; fifth, the strength of larger joints goes down; this is the size effect noted in many bend-cracking tests, much as Galileo suggested for bent beam fracture in his famous book ‘the larger the machine, the greater its weakness'. The purpose of this paper is to demonstrate that poor ASTM ‘shear strength’ standards should be replaced by a definition of welded lap joint performance based on Griffith's energy conservation argument in which fracture surface energy is the main parameter resisting failure. The foundation of this Griffith-style lap joint analysis for long cracks goes back to 1975 but has been largely ignored until now because it does not fit the Griffith equation for cracked sheets, has no ‘stress intensity factor’, and travels at constant speed, not accelerating like the standard Griffith tension crack. This study of tensile delamination shows that a long lap crack is not driven by stress near the crack but by changes in stored elastic energy in the stretched strips remote from the crack tip, while strain energy release rate is negative. It would be more appropriate to call this lap failure a tensile delamination crack. This article is part of a discussion meeting issue ‘A cracking approach to inventing new tough materials: fracture stranger than friction’.

Requirements and Variability Affecting the Durability of Bonded Joints

Energizing ASTM lap joint fracture standards

Evaluation of Fatigue Damage in Adhesive Bonding: Part 1: Bulk Adhesive

Multiaxial stress effects on bonding strength in adhesively bonded joints

Interfacial Fracture Mechanical Aspects of Adhesive Bonded Joints—A Review

Modelling the Variability and the Anisotropic Behaviour of Crack Growth in SLM Ti-6Al-4V

Mechanical Performance of Adhesive Connections in Structural Applications

Empirical Characterization and Modeling of Cohesive – to – Adhesive Shear Fracture Mode Transition due to Increased Adhesive Layer Thicknesses of Fiber Reinforced Composite Single – Lap Joints

Experimental and Numerical Evaluations on the Effects of Adhesive Fillet, Overlap Length and Unbonded Area in Adhesive‐bonded Joints

Influence of Failure-Load Prediction in Composite Single-Lap Joints with Brittle and Ductile Adhesives Using Different Progressive-Damage Techniques

Damage tolerance analysis of double strap joints with composite adherends

Investigation of Residual Strength in CFRP Double-Adhesive Single Lap Bonded Joints after Low-velocity Impact

Effect of Adhesive Layer Thickness on Strength of Carbon-Fiber-Reinforced Plastic/Aluminum Bond-Riveted Joints

Durability of anticorrosive-coated steel–carbon fiber reinforced polymer structural adhesive joint at high temperature and humidity

Mode II fatigue characteristics of a composite bonded joint with microstructured adhesive bondline through tailored sacrificial cracks

Predicting the Adhesive Layer Thickness in Hybrid Joints Involving Pre-Tensioned Bolts

Estimation of Crack Tip Position in Adhesively Bonded Joints Subjected to Mode II Fatigue Loading

Fatigue Behaviors and Mechanism-Based Life Evaluation on SPR-bonded Aluminum Joint

Identification of the Cohesive Parameters for Modelling of Bonded Joints between Flat Composite Adherends with Thick Layer of Adhesive

The effects of environments and adhesive layer thickness on the failure modes of composite material bonded joints

Effects of impact fatigue on residual static strength of adhesively bonded joints