Neurological aspects of organophosphate poisoning

J. Bleecker,J. Reuck,J. Willems

DOI: https://doi.org/10.1016/0303-8467(92)90065-B

1992-07-01

Abstract:

What problem does this paper attempt to address?

Development and properties of dental Ti–Zr binary alloys

Jie Jiang,Chuan Zhou,Yanwei Zhao,Fuming He,Xiaoxiang Wang

DOI: https://doi.org/10.1016/j.jmbbm.2020.104048

IF: 4.042

2020-01-01

Journal of the Mechanical Behavior of Biomedical Materials

Abstract:In this study, two medium Zr-containing Ti-based alloys with commercially pure titanium as control were systematically investigated to assess their potential biomedical application. After samples subjected to TMP and CR, it was found that the Zr addition significantly affected the microstructure, phase constitutions, mechanical properties and cytocompatibility. The microstructural results showed that increasing Zr concentrations resulted in more refined grains. Furthermore, Zr changed the phase constitution: CR Ti–20Zr was formed by the single α-phase while CR Ti–30Zr alloy was formed by the coexistence of α and deformation-induced FCC phases. The P-type FCC phase was dominant and more prone to occur than the B-type one. The mechanical tests demonstrated that the increasing Zr content led to a simultaneous increase in micro-hardness, strength and plasticity of CR samples due to the combined effects of solution strengthening, work hardening and the FCC phase. The SEM fractography indicated that the brittle fracture of CR Ti–20Zr due to deformation twins and ductile fracture of CR Ti–30Zr because of FCC phase. Furthermore, Ti–Zr alloys presented comparable cytocompatibility to the CP-Ti control based on cell viability, proliferation and intracellular O2− content of MSCs. Specifically, alkaline phosphatase activity in BMSCs were significantly higher for grain refined CR Ti–30Zr. Considering all these results, CR Ti–30Zr alloy exhibited the optimal comprehensive performance to be potential dental materials.
The characteristic and osteogenic effect of a nanoporous coating of zirconia implant

Li Li,Litao Yao,Lianjun Wu,Qingfang Ma,Jing Jiang,Shiyu Lin,Xufei Shen,Chengyi Huang,Lieping Sheng

DOI: https://doi.org/10.1016/j.ceramint.2022.06.135

IF: 5.532

2022-01-01

Ceramics International

Abstract:Zirconia ceramics have become increasingly used as dental implant material which is mainly due to their "tooth-like" color, superior biocompatibility, and excellent mechanical properties. However, the bio-inertness of the zirconia surface limits its use for a wider range of clinical applications. To enhance the surface bioactivity, a combination of magnetron sputtering, and anodization has in the present study been used to deposit a homogeneous nano-porous coating (ZrNP) on the zirconia surface (forming ZrO2/ZrNP with a ZrNP pore diameter of 20-30 nm, and a ZrNP layer thickness of similar to 2 mu m). EDS and XRD analysis showed that the distribution of the surface chemical components, as well as the crystalline structure of the zirconia (ZrO2), remained unchanged. On the other hand, the hydrophilicity of the ZrO2/ZrNP surface became significantly improved (as compared with a control group). In addition, the bond strength of the coating was decreased as a result of the anodization treatment. Moreover, both the Zr and ZrNP nanolayers exhibited improved proliferation and osteogenic properties in the in vitro cell experiment. Also, the ZrNP nanolayer was found to promote the biocompatibility and osteogenic ability to the largest extent. The ZrNP nanolayer did also provide numerous adhesion sites for MC3T3-E1 whereby the cell morphology could be enhanced. Additionally, the nano porous ZrNP layer improved the new bone formation around the zirconia implant and did robustly enhance the push out bond strength, thereby indicating the best osteointegration ability. In conclusion, a nano porous zirconium layer has been found to be very promising for the improvement of the bioactivity of the zirconia implant material.
Biomechanical and histomorphometric comparison between zirconia implants with varying surface textures and a titanium implant in the maxilla of miniature pigs

M Gahlert,T Gudehus,S Eichhorn,E Steinhauser,H Kniha,W Erhardt

DOI: https://doi.org/10.1111/j.1600-0501.2007.01401.x

Abstract:Background: Mechanical properties and biocompatibility make zirconia ceramics suitable implant material. The characteristics of tooth-color like, the ability to be machined and the low plaque affinity make zirconia especially suitable as a dental implant material. The influence of surface modification on the osseointegration of this material has not been extensively investigated. Purpose: Long-term investigations with titanium implants have shown superior biomechanical results with the sandblasted acid-etched (SLA) surface, demonstrating a high bone-implant interaction. The objective of this study was to compare two different zirconia surface topographies biomechanically and histologically with the well-documented titanium SLA surface. Material and methods: Zirconia implants with either a machined (ZrO2m) or a sandblasted (rough, ZrO2r) surface were manufactured with the exact same cylindrical shape with a standard ITI thread configuration as the SLA titanium implants. The incisors 2 and 3 were removed from both sides of the maxillae of 13 adult miniature pigs and the tissues left to heal for 6 months. After this time period the animals received a total of 78 implants using a randomized scheme, with the titanium SLA implant used as an only individual reference. After healing periods of 4, 8, and 12 weeks 20, 24, and 25 implants, respectively, were subjected to removal torque tests (RTQ) as the main biomechanical analysis of the of the study. A fewer number was resected on bloc, embedded in methylmethacrylat and analyzed for their direct bone apposition under a light microscope. Results: Surface analysis revealed the highest surface roughness for the SLA-implant, followed by ZrO2r and ZrO2m. The turned ZrO2m implants showed statistically significant lower RTQ values than the other two implants types after 8 and 12 weeks, while the SLA implant showed significantly higher RTQs values than ZrO2r surface after 8 weeks. Differences in the bone apposition were observed in the histomorphometric analysis using light microscopy for all surfaces at any time point. Conclusion: The findings suggest that ZrO2r implants can achieve a higher stability in bone than ZrO2m implants. Roughening the turned zirconia implants enhances bone apposition and has a beneficial effect on the interfacial shear strength.
A Comparison Study of the Osseointegration of Zirconia and Titanium Dental Implants. A Biomechanical Evaluation in the Maxilla of Pigs

Michael Gahlert,Stefan Röhling,Marco Wieland,Stefan Eichhorn,Helmut Küchenhoff,Heinz Kniha

DOI: https://doi.org/10.1111/j.1708-8208.2009.00168.x

2010-11-05

Clinical Implant Dentistry and Related Research

Abstract:OBJECTIVES: The purpose of the present study was to investigate the osseointegration of microstructured zirconia implants in comparison with sandblasted and acid-etched (SLA) titanium implants in a biomechanical study.MATERIALS: Zirconia implants (4.1 mm in diameter, 10 mm in length) were produced using a new low pressure injection molding technique. After that the implants were acid-etched with hydrofluoric acid. Standard Ti-SLA implants of the exact same shape served as controls. Six months after extraction of incisors 2 and 3, 16 adult pigs received a total of 64 implants in the maxillae. After 4, 8, and 12 weeks the animals were sacrificed, and 59 implants could be analyzed to removal torque (RTQ) testing.RESULTS: The mean RTQ values for zirconia implants were 42.4 Ncm at 4 weeks, 69.6 Ncm at 8 weeks, and 69.3 Ncm at 12 weeks of healing, whereas RTQ values for the Ti-SLA implants were 42.1 Ncm, 75.0 Ncm, and 73.1 Ncm at corresponding time intervals. There is no statistical difference in RTQ values between Ti-SLA and zirconia implants at 8 weeks.CONCLUSIONS: Within the limits of the present study it was concluded that acid-etching of zirconia implants enhances bone apposition resulting in RTQ values which were equivalent to that of Ti-SLA.

dentistry, oral surgery & medicine
Effect of Titanium and Zirconium Oxide Microparticles on Pro-Inflammatory Response in Human Macrophages under Induced Sterile Inflammation: An In Vitro Study

Liza L. Ramenzoni,Laura B. Flückiger,Thomas Attin,Patrick R. Schmidlin

DOI: https://doi.org/10.3390/ma14154166

IF: 3.4

2021-07-27

Materials

Abstract:The wear-debris particles released by shearing forces during dental implant insertion may contribute to inflammatory reactions or osteolysis associated with peri-implantitis by stimulating inflammasome-activation. The study aim was to examine cytotoxic and pro-inflammatory effects of titanium (TiO2) and zirconia (ZrO2) particles in macrophages regarding their nature/particle concentration over time under sterile lipopolysaccharide (LPS) inflammation. Macrophages were exposed to TiO2 and ZrO2 particles (≤5 μm) in cell culture. Dental glass was used as inert control and LPS (1 μg/mL) was used to promote sterile inflammation. Cytotoxicity was determined using MTT assays and cytokine expression of TNF-α, IL-1β and IL-6 was evaluated by qRT-PCR. Data were analyzed using Student’s t-test and ANOVA (p ≤ 0.05). Cytotoxicity was significantly increased when exposed to higher concentrations of glass, TiO2 and ZrO2 (≥107 particles/mL) compared to controls (p ≤ 0.05). Macrophages challenged with TiO2 particles expressed up to ≈3.5-fold higher upregulation than ZrO2 from 12 to 48 h. However, when exposed to LPS, TiO2 and ZrO2 particle-induced pro-inflammatory gene expression was further enhanced (p ≤ 0.05). Our data suggest that ZrO2 particles produce less toxicity/inflammatory cytokine production than TiO2. The present study shows that the biological reactivity of TiO2 and ZrO2 depends on the type and concentration of particles in a time-dependent manner.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
Early bone formation around immediately placed two-piece tissue-level zirconia implants with a modified surface: an experimental study in the miniature pig mandible

Roland Glauser,Peter Schupbach

DOI: https://doi.org/10.1186/s40729-022-00437-z

2022-09-14

Abstract:Purpose: To histologically examine early bone formation around transmucosal implants and to evaluate the influence of surface characteristics on early peri-implant bone healing using a miniature pig model. For this, commercially available dental implants with a rough zirconia (YTZP) surface were compared to surface-modified Ti control implants at 4 and 8 weeks after placement. Methods: Immediately following the extraction of six mandibular premolars, 20 two-piece, tissue-level, screw-shaped YTZP implants (Patent™ Standard Zirconia Implant ø4.1 × 11 mm) with a modified rough blasted before sintering surface were inserted in four adult miniature pigs. In addition, four titanium (Ti) tissue-level implants (Straumann® Standard RN ø4.1 × 10 mm Roxolid®) with a moderate surface (SLActive®), one per animal, were placed as control implants. A histological analysis was performed on the hard tissues after 4 and 8 weeks of transmucosal healing. Results: The results show a high rate of osseointegration of the test YTZP dental implants at 4 and 8 weeks following insertion. At 4 weeks, a bone-to-implant contact ratio (BIC) of 73.7% (SD ± 16.8) for the test implants (n = 10) and 58.5% for the first control implant was achieved. The second control implant had to be excluded from analysis. At 8 weeks, a BIC of 82.4% (SD ± 16.9) for the test implants (n = 9) and 93.6% (SD ± 9.1) (n = 2) for the control implant was achieved. No statistical difference was observed comparing 4 and 8 weeks YTZP data (p = 0.126). Conclusions: The results indicate a predictable osseointegration of immediate zirconia implants with a modified YTZP implant surface and a high degree of BIC present at 4 weeks following insertion. After 8 weeks of healing both the zirconia implants and the Ti implants show a BIC indicating full osseointegration. Further studies involving a larger sample size with more time points are needed to confirm these results.
Zirconia versus Titanium Implants: 8-Year Follow-Up in a Patient Cohort Contrasted with Histological Evidence from a Preclinical Animal Model

Warwick J. Duncan,Sunyoung Ma,Allauddin Siddiqi,Reham B. Osman

DOI: https://doi.org/10.3390/ma15155322

IF: 3.4

2022-08-03

Materials

Abstract:Zirconia ceramic (ZC) implants are becoming more common, but comparisons between preclinical histology and long-term clinical trials are rare. This investigation comprised (1) 8-year clinical follow-up of one-piece ZC or titanium (Ti) implants supporting full overdentures and (2) histomorphometric analysis of the same implants in an animal model, comparing implants with various surface treatments. Methods: (1) Clinical trial: 24 completely edentulous participants (2 groups of N = 12) received 7 implants (one-piece ball-abutment ZC or Ti; maxilla N = 4, mandible N = 3) restored with implant overdentures. Outcomes after 8-years included survival, peri-implant bone levels, soft-tissue responses, and prosthodontic issues. (2) Preclinical trial: 10 New Zealand sheep received 4 implants bilaterally in the femoral condyle: Southern Implants ZC or Ti one-piece implants, identical to the clinical trial, and controls: Southern ITC® two-piece implants with the same surface or Nobel (NBC) anodised (TiUniteTM) surface. %Bone-implant contact (%BIC) was measured after 12 weeks of unloaded healing. Results: 8 of 24 participants (33%) of an average age of 75 ± 8 years were recalled; 21% of original participants had died, and 46% could not be contacted. 80.4% of implants survived; excluding palatal sites, 87.5% of Ti and 79% of ZC implants survived. All failed implants were in the maxilla. Three ZC implants had fractured. Bone loss was similar for Ti vs. ZC; pocket depths (p = 0.04) and attachment levels (p = 0.02) were greater for Ti than ZC implants. (1.7 ± 1.6 mm vs. 1.6 ± 1.3 mm). All implants in sheep femurs survived. %BIC was not statistically different for one-piece blasted surface Ti (80 ± 19%) versus ZC (76 ± 20%) or ITC® (75 ± 16 mm); NBC had significantly higher %BIC than ITC (84 ± 17%, p = 0.4). Conclusion: Short-term preclinical results for ZC and Ti one-piece implants showed excellent bone-implant contact in unloaded femoral sites. This differed from the long-term clinical results in older-aged, edentulous participants. While ZC and Ti implants showed equivalent performance, the risks of peri-implantitis and implant loss in older, completely edentulous patients remain a significant factor.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
Osseointegration of zirconia implants compared with titanium: an in vivo study

Rita Depprich,Holger Zipprich,Michelle Ommerborn,Christian Naujoks,Hans-Peter Wiesmann,Sirichai Kiattavorncharoen,Hans-Christoph Lauer,Ulrich Meyer,Norbert R Kübler,Jörg Handschel

DOI: https://doi.org/10.1186/1746-160x-4-30

2008-12-01

Abstract:Abstract Background Titanium and titanium alloys are widely used for fabrication of dental implants. Since the material composition and the surface topography of a biomaterial play a fundamental role in osseointegration, various chemical and physical surface modifications have been developed to improve osseous healing. Zirconia-based implants were introduced into dental implantology as an altenative to titanium implants. Zirconia seems to be a suitable implant material because of its tooth-like colour, its mechanical properties and its biocompatibility. As the osseointegration of zirconia implants has not been extensively investigated, the aim of this study was to compare the osseous healing of zirconia implants with titanium implants which have a roughened surface but otherwise similar implant geometries. Methods Forty-eight zirconia and titanium implants were introduced into the tibia of 12 minipigs. After 1, 4 or 12 weeks, animals were sacrificed and specimens containing the implants were examined in terms of histological and ultrastructural techniques. Results Histological results showed direct bone contact on the zirconia and titanium surfaces. Bone implant contact as measured by histomorphometry was slightly better on titanium than on zirconia surfaces. However, a statistically significant difference between the two groups was not observed. Conclusion The results demonstrated that zirconia implants with modified surfaces result in an osseointegration which is comparable with that of titanium implants.

dentistry, oral surgery & medicine
Zirconia compared to titanium dental implants in preclinical studies—A systematic review and meta‐analysis

Stefan Roehling,Karl A. Schlegel,Henriette Woelfler,Michael Gahlert

DOI: https://doi.org/10.1111/clr.13425

2019-04-16

Clinical Oral Implants Research

Abstract:OBJECTIVES: To evaluate whether zirconia implants demonstrate differences in hard and soft tissue integration compared to titanium implants in preclinical studies.MATERIAL AND METHODS: In March 2017, electronic (MEDLINE, EMBASE) and hand search was performed to identify preclinical studies comparing zirconia and titanium implants. Primary outcomes were bone-to-implant contact (BIC) and removal torque out (RTQ), respectively, push-in (PI) measurements. Secondary outcomes included biologic width (BW) dimensions.RESULTS: A total of 37 studies were included for data extraction after screening of 91 from 1,231 selected titles. Thirty-seven experimental studies using six different species were identified. The follow-up periods ranged between 0.4 and 56 weeks. For titanium, mean values of 59.1% (95% CI: 53.3 - 64.8), 102.6 Ncm (95% CI: 81.5 - 123.6), and 25.1 N (95% CI: 20.2 - 30.0) for BIC, RTQ, and PI were estimated, respectively. The mean values for zirconia were 55.9% (95% CI: 51.6 - 60.1), 71.5 Ncm (95% CI: 51.1 - 91.9), and 22.0 N (95% CI: 13.2 - 30.7) for corresponding parameters. Confounding factors such as animal species, implant material, loading protocol, and study or loading duration significantly influenced the outcomes. Similar qualitative soft tissue integration was reported for zirconia and titanium implants. However, faster maturation processes of epithelial and connective tissues around zirconia implants were assumed. Quantitatively, similar BW dimensions were evaluated for titanium (3.5 mm; 95% CI: 2.9 - 4.2) and zirconia (3.2 mm; 95% CI: 2.7 - 3.7), whereas the loading protocol significantly influenced the outcomes.CONCLUSIONS: Zirconia and titanium implants demonstrate a similar soft and hard tissue integration capacity. However, titanium tended to show a faster initial osseointegration process compared to zirconia. Importantly, not only material characteristics but predominantly animal species and study protocols can significantly influence the outcomes.

engineering, biomedical,dentistry, oral surgery & medicine
Biomechanical and histological evaluation of the osseointegration capacity of two types of zirconia implant.

Jian-Min Han,Guang Hong,Hong Lin,Yoshinaka Shimizu,Yuhan Wu,Gang Zheng,Hongyu Zhang,Keiichi Sasaki

DOI: https://doi.org/10.2147/IJN.S119519

IF: 7.033

2016-01-01

International Journal of Nanomedicine

Abstract:The purpose of this study was to evaluate the biomechanical and histological behavior of a ceria-stabilized zirconia-alumina nanocomposite (NanoZr) in comparison with that of 3 mol% yttria-stabilized tetragonal zirconia polycrystalline (3Y-TZP) in Sprague Dawley rats. Cylindrical NanoZr and 3Y-TZP implants (diameter 1 mm, length 2 mm) were used. Implant-surface morphology and surface roughness were determined by scanning white-light interferometry and scanning electron microscopy, respectively. The cylindrical zirconia implants were placed at the distal edge of the femur of Sprague Dawley rats. At weeks 2, 4, and 8, the interfacial shear strength between implant and bone was measured by push-in test. Histological analysis was performed using hard-tissue sections. Bone-implant contact (BIC), the thickness of new bone around the implant within the bone marrow area, and osteoclast numbers were evaluated. The average surface roughness of 3Y-TZP (Sa 0.788 μm) was significantly higher than that of NanoZr (Sa 0.559 μm). The shear strengths of 3Y-TZP and NanoZr were similar at 2 weeks, but at 4 and 8 weeks the shear strength of NanoZr was higher than that of 3Y-TZP. The average BIC values within the bone marrow area for 3Y-TZP and NanoZr were 25.26% and 31.51% at 2 weeks, 46.78% and 38% at 4 weeks, and 47.88% and 56.81% at 8 weeks, respectively. The average BIC values within the cortical area were 38.86% and 58.42% at 2 weeks, 66.82% and 57.74% at 4 weeks, and 79.91% and 78.97% at 8 weeks, respectively. The mean BIC value did not differ significantly between the two zirconia materials at any time point. The NanoZr implants were biocompatible, capable of establishing close BIC, and may be preferred for metal-free dental implants.
Host inflammatory response and clinical parameters around implants in a rat model using systemic alendronate and zoledronate acid drug administrations

Kristian Kniha,Lothar Rink,Jana Wolf,Stephan Christian Möhlhenrich,Florian Peters,Marius Heitzer,Frank Hölzle,Ali Modabber

DOI: https://doi.org/10.1038/s41598-022-08308-8

IF: 4.6

2022-03-15

Scientific Reports

Abstract:Abstract Implant outcomes in comparison to a natural tooth in a rat model using systemic alendronate and zoledronate acid drug administrations were assessed. Fifty-four Sprague–Dawley rats were randomly allocated into two experimental groups (drug application of zoledronic acid; 0.04 mg/kg intravenously once a week and alendronic acid; 0.2 mg/kg subcutaneously five times a week) and one control group with 18 animals in each group. Drug delivery was conducted for a period of 4 months. After 4 weeks either a zirconia or a titanium implant was immediately inserted in the socket of the first molar of the upper jaw. In vivo investigations included host inflammatory parameters and the implant survival and success rates for up to 3 months. Material incompatibilities against titanium and zirconia nanoparticles were evaluated in vitro after stimulation of rat spleen cells. In vivo, IL-6 release around titanium implants demonstrated significantly higher values in the control group (p = 0.02) when compared to the zoledronic acid group. Around the natural tooth without drug administration, the control group showed higher IL-6 values compared with the alendronic acid group (p = 0.01). In vitro, only lipopolysaccharide and not the implant’s nanoparticles stimulated significant IL-6 and TNFα production. In terms of the primary aim of in vivo and in vitro IL-6 and TNFα measurements, no implant material was superior to the other. No significant in vitro stimulation of rat spleen cells was detected with respect to titanium oxide and zirconium oxide nanoparticles.

multidisciplinary sciences
The Performance of Titanium-Zirconium Implants in the Elderly: A Biomechanical Comparative Study in the Minipig.

Bo Wen,Jiang Chen,Michel Dard,Zhiyu Cai

DOI: https://doi.org/10.1111/cid.12389

2016-01-01

Clinical Implant Dentistry and Related Research

Abstract:OBJECTIVES:The aim of this study was to test the following hypothesis: (1) Aging would adversely affect bone integration of implants; (2) Titanium-zirconium-SLActive (TiZr-SLActive) implant might perform better in osseointegration than Ti-SLA implant in aged group.MATERIALS AND METHODS:Thirteen miniature pigs (six of them were young adult minipigs, with other seven being aged ones.) were enrolled in this study. The right mandibular premolars (P1, P2, P3) and the first molar (M1) were extracted in all animals. Three months later, one TiZr-SLActive and one Ti-SLA implants were inserted into the endentulous area in mandible of each animal. The animals were sacrificed 8 weeks after placement of implants. Implants in the mandibles were used for removal torque (RT) tests, while vertebra and femur being retrieved for bone mineral density (BMD) tests.RESULTS:Implant success rate in the young group was significantly higher than that in the aged group. Higher survival rate of implants was also observed in younger group than that in the aged group but without significant difference. Within the young group, mean value for peak RT of Ti-SLA implants was higher than that of TiZr-SLActive implants without significant difference. In the aged group, the TiZr-SLActive implants showed a higher mean value for peak RT than Ti-SLA implants. No significant difference was found in the mean BMD in both vertebra and femur between different age groups.CONCLUSIONS:Within the limits of this study, aging could negatively affect osseointegration of dental implants. TiZr-SLActive implants might to some degree compensate for the compromise in osseointegration brought by aging.
Amino Acid Based Synthesis of Chiral Long Chain Diamines and Tetramines

Vassilios Loukas,T. Markidis,G. Kokotos

DOI: https://doi.org/10.3390/71000767

IF: 4.6

2002-10-01

Molecules

Abstract:A method for the synthesis of long chain diamines and tetramines starting from natural α-amino acids is reported. Diamines and tetramines were prepared through the Wittig olefination reaction of N-protected amino aldehydes obtained from phenylalanine and lysine. A 1,2,17,18-tetramine was synthesized using (2S)-1-azido-2-[bis(tert-butoxycarbonyl)-amino]-5-oxopentane as key-intermediate compound.
Mesoporous TiO2 Coatings Regulate ZnO Nanoparticle Loading and Zn2+ Release on Titanium Dental Implants for Sustained Osteogenic and Antibacterial Activity.

Xinyue Shi,Jiansheng Su,Zhu Wen,Weicai Liu,Yiqiang Yu,Yukun Liu,Renyuan Zhang,Xuejing Li

DOI: https://doi.org/10.1021/acsami.3c00812

2023-03-17

Abstract:Two major issues are currently hindering the clinical practice of titanium dental implants for the lack of biological activities: immediate/early loading risks and peri-implantitis. To solve these issues, it is urgent to develop multifunctional implants modified with effective osteogenic and antibacterial properties. Zinc oxide nanoparticles (ZnO NPs) possess superior antibacterial activity; however, they can rapidly release Zn2+, causing cytotoxicity. In this study, a potential dental implant modification was creatively developed as ZnO nanoparticle-loaded mesoporous TiO2 coatings (nZnO/MTC-Ti) via the evaporation-induced self-assembly method (EISA) and one-step spin coating. The mesoporous TiO2 coatings (MTCs) regulated the synthesis and loading of ZnO NPs inside the nanosized pores. The synergistic effects of MTC and ZnO NPs on nZnO/MTC-Ti not only controlled the long-term steady-state release of Zn2+ but also optimized the charge distribution on the surface. Therefore, the cytotoxicity of ZnO NPs was resolved without triggering excessive reactive oxygen species (ROS). The increased extracellular Zn2+ further promoted a favorable intracellular zinc ion microenvironment through the modulation of zinc transporters (ZIP1 and ZnT1). Owing to that, the adhesion, proliferation, and osteogenic activity of bone mesenchymal stem cells (BMSCs) were improved. Additionally, nZnO/MTC-Ti inhibited the proliferation of oral pathogens (Pg and Aa) by inducing bacterial ROS production. For in vivo experiments, different implants were implanted into the alveolar fossa of Sprague-Dawley rats immediately after tooth extraction. The nZnO/MTC-Ti implants were found to possess a higher capability for enhancing bone regeneration, antibiosis, and osseointegration in vivo. These findings suggested the outstanding performance of nZnO/MTC-Ti implants in accelerating osseointegration and inhibiting bacterial infection, indicating a huge potential for solving immediate/early loading risks and peri-implantitis of dental implants.

Engineering,Medicine,Materials Science
Toxicity, biodistribution and oxidative damage caused by zirconia nanoparticles after intravenous injection

Yue Yang,Huihui Bao,Qianqian Chai,Zhiwen Wang,Zhenning Sun,Changhui Fu,Zhaoping Liu,Zhongjie Liu,Xianwei Meng,Tianlong Liu

DOI: https://doi.org/10.2147/IJN.S197565

IF: 7.033

2019-11-22

International Journal of Nanomedicine

Abstract:Yue Yang, 1,2 Huihui Bao, 1 Qianqian Chai, 3 Zhiwen Wang, 2 Zhenning Sun, 2 Changhui Fu, 3 Zhaoping Liu, 1 Zhongjie Liu, 2 Xianwei Meng, 3 Tianlong Liu 2 1 China National Center for Food Safety Risk Assessment, Beijing 100022, People's Republic of China; 2 Key Laboratory of Animal Epidemiology of Ministry of Agriculture, College of Veterinary Medicine, China Agricultural University, Beijing 100193, People's Republic of China; 3 Laboratory of Controllable Preparation and Application of Nanomaterials, Technical Institute of Physics and Chemistry, Chinese Academy of Sciences, Beijing 100190, People's Republic of China Background: As a promising nanomaterial for biomedical applications, zirconia nanoparticles (ZrO 2 ) have aroused concern recently, but the toxicity of ZrO 2 in vivo has received little attention. Purpose: The aim of this study is to demonstrate the systematic single dose toxicity, biodistribution and oxidative damage of ZrO 2 in vivo after intravenous injection in mice. Materials and methods: Ten ICR mice were used at the high dose of ZrO 2 including 600, 500, 400 and 300mg/kg. Maximum tolerated dose (MTD) of 150 nm ZrO 2 was determined as 500mg/kg. Hematology analysis and blood biochemical assay were determined for the evaluation of oxidative damage caused by ZrO 2 . Biodistribution of ZrO 2 was investigated by ICP-OES and TEM. Results: Mice treated with higher dose (500mg/kg) showed significant spread in white blood cell counts ( p <0.05). Especially, the serum ALT levels of 500mg/kg groups increased significantly ( p <0.05) compared with the control group. ZrO 2 particles would not induce any changes in appearance and micromorphology of liver at 100 and 350mg/kg. Spleen samples showed no significant changes in micromorphology of the lymphoid follicles and in the size of the red pulp after injection of ZrO 2 at all doses. The serum of ZrO 2 -treated animals (350 and 500mg/kg) has reduced levels of SOD compared to the control group ( p <0.05). ZrO 2 persists in membrane-enclosed vesicles called lysosomes in the liver and spleen macrophages without abnormal changes of ultrastructure. Conclusion: These findings would contribute to the future development of ZrO 2 -based drug delivery system and other biomedical applications. Keywords: zirconia nanoparticles, toxicity, biodistribution, oxidative damage, ICP-OES

pharmacology & pharmacy,nanoscience & nanotechnology
Inflammatory Response to Wear Particles: Comparisons Between Zirconia and Titanium In Vitro

Julia Olander,Anna-Karin Östberg,Karin Christenson,Petra Hammarström Johansson,Ann Wennerberg,Victoria Franke Stenport

DOI: https://doi.org/10.11607/jomi.10546

2024-06-21

Abstract:Purpose: To compare the inflammatory responses of peripheral blood mononuclear cells (PBMCs) subjected to titanium (Ti) and/or zirconia (Zr) particles while growing on Ti or Zr discs. Materials and methods: In total, 240 discs were fabricated at a size of 2 mm in height and 5 mm in diameter. Of the 240 discs, 120 discs were made of Ti (commercially pure [CP] grade 4), and 120 discs were made of Zr (3 mol% yttria-stabilized zirconia polycrystals [3Y-TZP]). The PBMCs were cultured on the two-disc materials, and particles with a size up to 20 mm Ti (99.5% Ti) and 0.1 to 0.2 mm Zr (3Y-TZP) were added to the cultures. The concentration levels of inflammatory cytokines in culture supernatants were measured through Bio-Plex assay (Bio-Rad Laboratories), and light microscopic analysis was performed to detect cell attachment and characterize particle shape and cell-particle interaction. Results: The inflammatory responses of PBMCs were generally higher when cells were cultured on a Ti surface compared to a Zr surface. In addition, higher cytokine levels were seen when cells were cultured in the presence of Ti particles compared to Zr particles when no discs were used. However, there were only significantly increased levels for three cytokines (MCP-1, IFN-γ, and TNF-α) when particles were added to Ti discs. Higher release of neutrophil extracellular traps (NETs) from neutrophils were seen in presence of Zr particles compared to Ti particles. A reduction in cell death was observed in the presence of Zr particles compared to Ti particles and unstimulated control samples. Conclusions: The type of growth material and presence of particle affects PBMCs in vitro. Cells seeded on Ti discs and together with Ti particles generated higher levels of inflammatory cytokines compared to the Zr counterparts.
Finite element analysis of a one-piece zirconia implant in anterior single tooth implant applications

Georgi Talmazov,Nathan Veilleux,Aous Abdulmajeed,Sompop Bencharit

DOI: https://doi.org/10.1371/journal.pone.0229360

IF: 3.7

2020-02-24

PLoS ONE

Abstract:This study evaluated the von Mises stress (MPa) and equivalent strain occurring around monolithic yttria-zirconia (Zir) implant using three clinically simulated finite element analysis (FEA) models for a missing maxillary central incisor. Two unidentified patients' cone-beam computed tomography (CBCT) datasets with and without right maxillary central incisor were used to create the FEA models. Three different FEA models were made with bone structures that represent a healed socket (HS), reduced bone width edentulous site (RB), and immediate extraction socket with graft (EG). A one-piece abutment-implant fixture mimicking Straumann Standard Plus tissue level RN 4.1 X 11.8mm, for titanium alloy (Ti) and Zir were modeled. 178 N oblique load and 200 N vertical load were used to simulate occlusal loading. Von Mises stress and equivalent strain values for around each implant model were measured. Within the HS and RB models the labial-cervical region in the cortical bone exhibited highest stress, with Zir having statistically significant lower stress-strain means than Ti in both labial and palatal aspects. For the EG model the labial-cervical area had no statistically significant difference between Ti and Zir; however, Zir performed better than Ti against the graft. FEA models suggest that Ti, a more elastic material than Zir, contributes to the transduction of more overall forces to the socket compared to Zir. Thus, compared to Ti implants, Zir implants may be less prone to peri-implant bone overloading and subsequent bone loss in high stress areas especially in the labial-cervical region of the cortical bone. Zir implants respond to occlusal loading differently than Ti implants. Zir implants may be more favorable in non-grafted edentulous or immediate extraction with grafting.

multidisciplinary sciences
Zirconia Nanoparticles-Induced Toxic Effects in Osteoblast-Like 3T3-E1 Cells

Mingfu Ye,Bin Shi

DOI: https://doi.org/10.1186/s11671-018-2747-3

2018-01-01

Nanoscale Research Letters

Abstract:Zirconia (ZrO 2 ) is one of the widely used metal oxides for potential bio-applications such as biosensors, cancer therapy, implants, and dentistry due to its high mechanical strength and less toxicity. Because of their widespread applications, the potential exposure to these nanoparticles (NPs) has increased, which has attracted extensive attention. Thus, it is urgent to investigate the toxicological profile of ZrO 2 NPs. Titanium dioxide (TiO 2 ) is another extensively used nanomaterials which are known to be weakly toxic. In this study, TiO 2 NPs were served as control to evaluate the biocompatibility of ZrO 2 NPs. We detected the cytotoxicity of TiO 2 and ZrO 2 NPs in osteoblast-like 3T3-E1 cells and found that reactive oxygen species (ROS) played a crucial role in the TiO 2 and ZrO 2 NP-induced cytotoxicity with concentration-dependent manner. We also showed TiO 2 and ZrO 2 NPs could induce apoptosis and morphology changes after culturing with 3T3-E1 cells at high concentrations. Moreover, TiO 2 and ZrO 2 NPs at high concentrations could inhibit cell osteogenic differentiation, compared to those at low concentrations. In conclusion, TiO 2 and ZrO 2 NPs could induce cytotoxic responses in vitro in a concentration-dependent manner, which may also affect osteogenesis; ZrO 2 NPs showed more potent toxic effects than TiO 2 NPs.
Osseointegration of zirconia implants: an SEM observation of the bone-implant interface

Rita Depprich,Holger Zipprich,Michelle Ommerborn,Eduardo Mahn,Lydia Lammers,Jörg Handschel,Christian Naujoks,Hans-Peter Wiesmann,Norbert R Kübler,Ulrich Meyer

DOI: https://doi.org/10.1186/1746-160X-4-25

2008-11-06

Abstract:Background: The successful use of zirconia ceramics in orthopedic surgery led to a demand for dental zirconium-based implant systems. Because of its excellent biomechanical characteristics, biocompatibility, and bright tooth-like color, zirconia (zirconium dioxide, ZrO2) has the potential to become a substitute for titanium as dental implant material. The present study aimed at investigating the osseointegration of zirconia implants with modified ablative surface at an ultrastructural level. Methods: A total of 24 zirconia implants with modified ablative surfaces and 24 titanium implants all of similar shape and surface structure were inserted into the tibia of 12 Göttinger minipigs. Block biopsies were harvested 1 week, 4 weeks or 12 weeks (four animals each) after surgery. Scanning electron microscopy (SEM) analysis was performed at the bone implant interface. Results: Remarkable bone attachment was already seen after 1 week which increased further to intimate bone contact after 4 weeks, observed on both zirconia and titanium implant surfaces. After 12 weeks, osseointegration without interposition of an interfacial layer was detected. At the ultrastructural level, there was no obvious difference between the osseointegration of zirconia implants with modified ablative surfaces and titanium implants with a similar surface topography. Conclusion: The results of this study indicate similar osseointegration of zirconia and titanium implants at the ultrastructural level.

Neurological aspects of organophosphate poisoning

Development and properties of dental Ti–Zr binary alloys

The characteristic and osteogenic effect of a nanoporous coating of zirconia implant

Biomechanical and histomorphometric comparison between zirconia implants with varying surface textures and a titanium implant in the maxilla of miniature pigs

A Comparison Study of the Osseointegration of Zirconia and Titanium Dental Implants. A Biomechanical Evaluation in the Maxilla of Pigs

Effect of Titanium and Zirconium Oxide Microparticles on Pro-Inflammatory Response in Human Macrophages under Induced Sterile Inflammation: An In Vitro Study

Early bone formation around immediately placed two-piece tissue-level zirconia implants with a modified surface: an experimental study in the miniature pig mandible

Zirconia versus Titanium Implants: 8-Year Follow-Up in a Patient Cohort Contrasted with Histological Evidence from a Preclinical Animal Model

Osseointegration of zirconia implants compared with titanium: an in vivo study

Zirconia compared to titanium dental implants in preclinical studies—A systematic review and meta‐analysis

Biomechanical and histological evaluation of the osseointegration capacity of two types of zirconia implant.

Host inflammatory response and clinical parameters around implants in a rat model using systemic alendronate and zoledronate acid drug administrations

The Performance of Titanium-Zirconium Implants in the Elderly: A Biomechanical Comparative Study in the Minipig.

Amino Acid Based Synthesis of Chiral Long Chain Diamines and Tetramines

Mesoporous TiO2 Coatings Regulate ZnO Nanoparticle Loading and Zn2+ Release on Titanium Dental Implants for Sustained Osteogenic and Antibacterial Activity.

Toxicity, biodistribution and oxidative damage caused by zirconia nanoparticles after intravenous injection

Inflammatory Response to Wear Particles: Comparisons Between Zirconia and Titanium In Vitro

Finite element analysis of a one-piece zirconia implant in anterior single tooth implant applications

Zirconia Nanoparticles-Induced Toxic Effects in Osteoblast-Like 3T3-E1 Cells

Osseointegration of zirconia implants: an SEM observation of the bone-implant interface