Narrow linewidth erbium-doped fiber laser incorporating with photonic crystal fiber based Fabry–Pérot interferometer for temperature sensing applications

Yu Zhang,Xiangqiang Bu
DOI: https://doi.org/10.1016/j.ijleo.2020.165005
IF: 3.1
2020-10-01
Optik
Abstract:<p>We propose a narrow linewidth ring cavity erbium-doped fiber laser based on a photonic crystal fiber (PCF) based Fabry–Pérot interferometer (F–P). A 5.2-m-long erbium-doped fiber was used in the resonant cavity as gain medium. The F–P was fabricated by cascaded with single-mode fiber and 2 mm length PCF as the interferometer filter, and the interferometer period was 0.58 nm. The laser threshold was 57 mW in the experiment, and 1573.99 nm narrow linewidth lasing was realized and 3 dB linewidth was 0.2 nm. Single wavelength laser temperature sensing was implemented by heating and cooling the F–P filter. In the experiment, single-wavelength lasing could be tuned from 1573.25–1574.27 nm within 40–120 ℃, with 12.6 pm/℃ sensitivity, power fluctuation was lower than 1.78 dB, and linearity was more than 0.996. The single-wavelength laser temperature stability was tested, and power fluctuation was less than 0.819 dB within 25 min scan time. In addition, four different dual-wavelength lasers could be obtained with power shift less than 1.187 dB.</p>
optics
What problem does this paper attempt to address?
The problem that this paper attempts to solve is to develop a narrow - linewidth erbium - doped fiber laser (EDFL) based on a Fabry - Pérot interferometer (F - P) of photonic crystal fiber (PCF) for temperature sensing applications. Specifically, the researchers hope to achieve the following goals: 1. **Achieve narrow - linewidth laser output**: By using a PCF - based F - P interferometer as a filter, single - wavelength narrow - linewidth laser output is achieved to improve the stability and signal - to - noise ratio of the laser. 2. **Temperature sensing ability**: Utilize the temperature - sensitive characteristics of the F - P interferometer to achieve accurate measurement of temperature changes. The researchers achieve temperature sensing by heating and cooling the F - P filter and observing the change in laser wavelength. 3. **Stability test**: Test the stability and power fluctuation of the laser at different temperatures to ensure its reliability and accuracy in practical applications. 4. **Multi - wavelength laser output**: By adjusting the polarization controller (PC), dual - wavelength laser output is achieved and its performance is evaluated. ### Main Results - **Narrow - linewidth laser output**: A single - wavelength laser output of 1573.99 nm is achieved, with a 3 - dB linewidth of 0.2 nm and a signal - to - noise ratio (SNR) higher than 23.2 dB. - **Temperature sensing performance**: In the temperature range from 40 °C to 120 °C, the sensitivity of the laser wavelength to temperature change is 12.6 pm/°C, and the linearity exceeds 0.996. - **Temperature stability**: At 90 °C and 100 °C, the power fluctuations of the laser are respectively less than 0.819 dB and 0.241 dB, showing good temperature stability. - **Multi - wavelength laser output**: By adjusting the PC, four different sets of dual - wavelength laser output are achieved, with a power difference less than 1.187 dB. ### Formula The transfer function of the reflection wavelength of the F - P interferometer mentioned in the paper can be expressed as: \[ \lambda_m=\frac{2nL}{m} \quad (m = 0, 1, 2, \ldots) \] where: - \( \lambda_m \) is the wavelength of the \( m \)-th - order interference fringe, - \( n \) is the refractive index in the cavity, - \( L \) is the length of the F - P cavity, - \( m \) is the interference order. ### Conclusion This research successfully designs and experimentally verifies a narrow - linewidth EDFL based on a PCF - based F - P interferometer, which not only achieves single - wavelength and dual - wavelength laser output, but also shows excellent temperature sensing performance and stability. This result has broad application prospects in fields such as fiber - optic laser sensors, communications, and spectral analysis.