Abstract:Objectives: This study aimed to assess the surface roughness, surface free energy (SFE), and shear bond strength (SBS) on a lithium disilicate glass-ceramic surface following varying etching protocols (time variation) and application of silane either with or without adhesive material. Methods and materials: Lithium disilicate glassceramic (LDGC) computer-aided design and computer-aided manufacture (CAD/CAM) blocks were cut using a slow-speed cutting mechanism. CAD/CAM blocks were then evaluated for surface roughness, 6 groups (n=20); SFE,12 groups (n=5); and SBS, 10 groups (n=10). The cut CAD/CAM blocks were randomly allocated to 28 groups. Groups were based on the following: 30 or 90 seconds of etching with 9% hydrofluoric acid (HF); application or absence of silane coupling agent (Sil); and application or absence of adhesive (Adh).The control group (Cont) had untreated surfaces. Unetched surfaces were surveyed with only silane (Sil), only adhesive (Adh), or silane+adhesive (SilAdh). Further etched groups were HF30 with HF for 30 seconds, HF30-Sil, HF30-Adh, and HF30-SilAdh. Alternative 90-second etching times produced similar groups: HF90, HF90-Sil, HF90-Adh, and HF90-SilAdh. A digital profilometer was used to assess the surface roughness of specimens, and two readings were recorded. Sessile drop analysis was used to examine SFE specimens, and the OWRK model was modified to measure liquid surface tension. A universal testing machine (UltraTester, Ultradent Products, Inc, South Jordan, UT, USA) was utilized for the SBS test, with the crosshead speed set at 0.5 mm/min until failure. Representative treated specimens from each group were submitted to surface morphological evaluation and chemical analysis using scanning electron microscopy/energy dispersive x-ray spectroscopy (SEM/EDXS) (n=3). After data collection, evaluation using one- or two-way analysis of variance and the post-hoc Tukey test (α=5%) was conducted. Results: A longer etching time of 90 seconds produced a rougher surface. After the 90-second etching process, SFE displayed the greatest values; nevertheless, the use of silane did not affect SFE. For every group examined, the application of silane followed by adhesive resulted in an increase in SBS and more stable bonding over time. SEM/EDXS showed that etching times did affect the amount of cerium on the surface and altered surface morphology. Conclusions: Higher and more consistent bond strengths have been observed with longer etching periods. Silane and adhesive application on the ceramic surface showed stronger and enhanced bond strength, specifically when longer etching times were employed.

Silane reactivity and resin bond strength to lithium disilicate ceramic surfaces

Optimal Hydrofluoric Acid Etching Duration and Impact of Silane/Adhesive on Profilometric Properties and Bonding to Lithium Disilicate Glass Ceramics

Influence of Varied Silane Commercial Brands and Adhesive Application on Bond Strength and Stability to Lithium Disilicate Glass Ceramic

Chemical surface modification of lithium disilicate needles of a silica-based ceramic after HF-etching and ultrasonic bath cleaning: impact on the chemical bonding with silane

Increasing Acid Concentration, Time and Using a Two-Part Silane Potentiates Bond Strength of Lithium Disilicate–Reinforced Glass Ceramic to Resin Composite: An Exploratory Laboratory Study

Bond Strength to Lithium-Disilicate Ceramic after Different Surface Cleaning Approaches

Effects of Surface Treatment Procedures on Bond Strength of Lithium Disilicate Glass Ceramic.

Effect of siloxane quantity and ph of silane coupling agents and contact angle of resin bonding agent on bond durability of resin cements to machinable ceramic.

Effect of Silane Coupling Agent on Composite-Composite Bond Strength: an in Vitro Study

Is additional silane application necessary for a new silane‐containing universal adhesive to bond to glass ceramics?

Chemical adhesion rather than mechanical retention enhances resin bond durability of a dental glass-ceramic with leucite crystallites

Does the surface conditioning of glass and hybrid ceramics with self-etching silane present a bond strength similar to that of conventional bonding? Systematic review and meta-analysis of in vitro studies

Effects of Different Surface Treatments on Ceramic Repairs with Composite.

The effect of three silane coupling agents and their blends with a cross-linker silane on bonding a bis-GMA resin to silicatized titanium (a novel silane system)

[Effect of Hydrofluoric Acid Concentration on the Surface Morphology and Bonding Effectiveness of Lithium Disilicate Glass Ceramics to Resin Composites].

Influence of post-etch cleaning and silane heat treatment on resin bond strength to silica-based leucite: an in vitro study

Influence of Different Surface Pretreatments of Zirconium Dioxide Reinforced Lithium Disilicate Ceramics on the Shear Bond Strength of Self-Adhesive Resin Cement

Influence of lithium disilicate pretreatment using photodynamic therapy, non-thermal plasma, and laser treatment on surface roughness and bond strength

Shear bond, wettability and AFM evaluations on CO2 laser-irradiated CAD/CAM ceramic surfaces

Silane Heat Treatment Could Eliminate the Hydrofluoric Acid Etching of Lithium Disilicate Overlays: A Four-Year Follow-Up

The effect of adhesive surface with porcelain sintering and two silane coupling agents on the adhesive properties of zirconia