Abstract:Three-dimensional (3D) printing is a bio-fabrication technique used to process tissue-engineered scaffolds for bone repair and remodeling. Polycaprolactone (PCL)/β-tricalcium phosphate (TCP) has been used as a base and osteoconductive biomaterial for bone tissue engineering in the past decades. The current study reveals the fabrication of a polycaprolactone (PCL)/β-tricalcium phosphate (TCP) scaffold by incorporating carbon nanotubes (CNT) via 3D printing. The physical properties and cytocompatibility of a new type of tissue engineering composite from polycaprolactone/β-tri-calcium phosphate/carbon nanotubes were investigated, and it was an absorbable scaffold prepared via furnace deposition 3D printing technology. The scaffold was designed with CAD software, and the composite material was fabricated via 3D printing. The printed composite material was tested for mechanical strength, scanning electron microscope (SEM) analysis, porosity calculation, systemic toxicity test, hemolysis rate determination, and effect on the proliferation of rat adipose-derived stem cells cultured in vitro. A composite scaffold with a length of 15 mm, width of 10 mm, and height of 5 mm was manufactured through CAD software drawing and 3D printing technology. Scanning electron microscopy measurements and analysis of the internal pore size of the stent are appropriate; the pores are interconnected, and the mechanical strength matches the strength of human cancellous bone. The calculated porosity of the stent was >60%, non-toxic, and non-hemolytic. The proliferation activity of the ADSC co-cultured with different scaffold materials was as follows: polycaprolactone/β-tricalcium phosphate/0.2% carbon nanotube scaffolds > polycaprolactone/β-tricalcium phosphate/0.1% carbon nanotube scaffolds > polycaprolactone/β-tricalcium phosphate/0.3% carbon nanotube scaffolds > polycaprolactone/β-tricalcium phosphate scaffolds (P < 0.05). The results showed that polycaprolactone/β-tricalcium phosphate/0.2% carbon nanotube scaffolds promoted the adhesion and proliferation of ADSC. The combination of 3D printing technology and CAD software can be used to print personalized composite stents, which have the characteristics of repeatability, high precision, and low cost. Through 3D printing technology, combining a variety of materials with each other can provide the greatest advantages of materials. The waste of resources was avoided. The prepared polycaprolactone/β-tri-calcium phosphate/0.2% carbon nanotube scaffold has a good pore structure and mechanical properties that mimic human cancellous bone, is non-toxic and non-hemolytic, and is effective in promoting ADSC proliferation in vitro. Given this correspondence, 3D printed scaffold shows good biocompatibility and strength, and the fabrication method provides a proof of concept for developing scaffolds for bone tissue engineering applications.

3D Printed Polycaprolactone Carbon Nanotube Composite Scaffolds for Cardiac Tissue Engineering

3D printed polycaprolactone/β-tricalcium phosphate/carbon nanotube composite - Physical properties and biocompatibility

3D Printed PEEK Smart Polymer Nanocomposite Scaffolds: Mechanical, Self‐Sensing, and Biological Attributes

3D printing of HA / PCL composite tissue engineering scaffolds

Composite Poly(lactic Acid)/chitosan Nanofibrous Scaffolds for Cardiac Tissue Engineering.

A Combined Computational and Experimental Analysis of PLA and PCL Hybrid Nanocomposites 3D Printed Scaffolds for Bone Regeneration

On 3D printed thermoresponsive PCL-PLA nanofibers based architected smart nanoporous scaffolds for tissue reconstruction

Graphene-enhanced PCL electrospun nanofiber scaffolds for cardiac tissue engineering

In Vitro and In Vivo Characterization of Multi-Walled Carbon Nanotubes/Polycaprolactone Composite Scaffolds for Bone Tissue Engineering Applications

Development and Evaluation of 3D-Printed PLA/PHA/PHB/HA Composite Scaffolds for Enhanced Tissue-Engineering Applications

Three Dimensional Printed Degradable and Conductive Polymer Scaffolds Promote Chondrogenic Differentiation of Chondroprogenitor Cells

Microstructures and Properties of Polycaprolactone/tricalcium Phosphate Scaffolds Containing Polyethylene Glycol Fabricated by 3D Printing

Early In Vivo Osteogenic and Inflammatory Response of 3D Printed Polycaprolactone/Carbon Nanotube/Hydroxyapatite/Tricalcium Phosphate Composite Scaffolds

Robocasting nanocomposite scaffolds of poly(caprolactone)/hydroxyapatite incorporating modified carbon nanotubes for hard tissue reconstruction

3D Biocompatible Polyester Blend Scaffolds Containing Degradable Calcium Citrate for Bone Tissue Engineering

Fabrication of Shish-Kebab-structured Carbon Nanotube/poly（ε-Caprolactone） Composite Nanofibers for Potential Tissue Engineering Applications

3D printing of PCL-ceramic composite scaffolds for bone tissue engineering applications

Electrohydrodynamic 3D Printing of Microscale Poly ( Ε -Caprolactone) Scaffolds with Multi-Walled Carbon Nanotubes

The Effect of Spironolactone Loading on the Properties of 3D-Printed Polycaprolactone/Gold Nanoparticles Composite Scaffolds for Myocardial Tissue Engineering

3D Printed Polycaprolactone/Gelatin/Bacterial Cellulose/Hydroxyapatite Composite Scaffold for Bone Tissue Engineering

Experimental investigation of PCL‐based composite material fabricated using solvent‐cast 3D printing process