Abstract:Abstract After polymer flooding, a low-resistant dominant seepage channel forms at the bottom of the high-permeability reservoir, which is extremely disadvantageous for further enhanced oil recovery. In this study, we proposed a new method to plug the dominant seepage channel after polymer flooding, through fracturing–seepage–plugging using a solid-free plugging agent, which can achieve deeper and further regional plugging. This method involved dissolving the crosslinking agent and stabilizer in the water-based fracturing fluid (hereinafter referred to as the fracturing plugging agent) and transporting it to the target reservoir through hydraulic fractures. The fracturing plugging agent percolated into the deep part of the reservoir under the action of fracture closure pressure and gelled with the residual polymer in the formation to achieve deep regional plugging of the advantageous channel. To study the percolation law of fracturing plugging agent in the dominant channel, high-pressure displacement experiments were conducted using natural cores under different permeability and concentration conditions of the fracturing plugging agent. The results showed that the percolation rate of the fracturing plugging agent was almost linearly related to reservoir permeability. Due to the formation of micro-fractures and crosslinking reactions, the percolation rate first increased and then decreased to a stable state. After a certain period, the pores were blocked, resulting in a sharp decrease in the percolation rate and then decayed. In addition, the higher the concentration of fracturing plugging agent, the better the core plugging performance. Moreover, when the concentration of fracturing plugging agent injected into the core exceeded 3,000 mg/L, the core permeability increased, and the breakthrough pressure evidently increased three to four times. On the basis of this, rheometer tests, scanning electron microscopy (SEM) observations, and mercury intrusion tests were performed to evaluate gelation performance, shear effect, and pore retention morphology of the crosslinking system made by mixing the injected plugging agent and residual polymer in the reservoir. The results showed that the shear action could reduce the gelling property, and the concentration of fracturing plugging agent should be >3,000 mg/L to meet the requirements of gelling. Furthermore, the viscosity of the crosslinking system reached the peak value at approximately 72 h, forming a network space structure of layered superposition, thereby increasing viscosity by 40–50 times. Finally, SEM images revealed that after the fracture plugging agent was injected into the core, the micelles were mostly concentrated in the front and middle sections. The average pore radius of the core decreased by 8.620 μm, and the average porosity decreased by 54.85%.

Research on Crack Sealing Performance of Polymer Microsphere/Hydrogel Composite System

Smart Nanoparticles for Conformance Improvement in Waterflooding

Development and performance evaluation of hydrophobic association plugging agents for sealing formation prior to cementing

Development and Performance Evaluation of a New Conformance Control Agent Gel

Synthesis and Plugging Mechanism of New Water-Swellable Rubber Particles for Fractured Pores in High Water-Cut Reservoirs

A new method for plugging the dominant seepage channel after polymer flooding and its mechanism: Fracturing–seepage–plugging

Synthesis and Performance Evaluation of a Novel Nanoparticle Coupling Expanded Granule Plugging Agent

Performance and enhanced oil recovery efficiency of an acid-resistant polymer microspheres of anti-CO2 channeling in low-permeability reservoirs

Experimental Study of Oilfield Water Plugging with Organic Chromium Gel

Experimental Study of Synergy between Polymeric Microspheres and Nanoemulsions for Profile Control and Water Plugging

Pore-Scale Investigation on the Plugging Behavior of Submicron-Sized Microspheres for Heterogeneous Porous Media with Higher Permeability

The preparation and displacement performances of a hollow structure microsphere with swelling–deswelling properties for enhanced oil recovery (EOR)

Study on increasing polymer gel strength with Janus nanoparticles and its feasibility in profile control and water plugging

Feasibility Study on the Microspheres for Deep Profile Control Technology in High Permeability of High Temperature and High Salinity Reservoirs

APPLICATION PROGRESS OF INSITU POLYMER GEL IN OILFIELD CONFORMANCE CONTROL TREATMENT

Synergism of polyvinyl alcohol fiber to hydrogel for profile modification

Investigation on the Adaptability of the Polymer Microspheres for Fluid Flow Diversion in Porous Media

Development of dual-crosslinked nanocomposite gel for water management in high-temperature reservoirs

Investigation of In Situ Gelation Behavior and Enhanced Oil Recovery Ability of Polymer Gel Used for Controlling CO2 Channeling in Tight Fractured Reservoir

Experimental Research on Seepage Law and Migration Characteristics of Core-Shell Polymeric Nanoparticles Dispersion System in Porous Media

Preparation, Evaluation and Field Application of Thermally Induced Crosslinked Polymer Gel Leakage Plugging Agent