Abstract:Crystallographic textures and their effect on the mechanical anisotropy of a hot-rolled biomedical Co-Cr-Mo alloy were investigated. The hot-rolled Co-28Cr-6Mo-0.13N (mass%) alloy examined here exhibited a monotonic strength increment following hot-rolling reduction, eventually reaching a 0.2% proof stress of 1400 MPa while maintaining acceptable ductility (>10%). The dominant hot-rolling texture was a brass-type component, which is characterized by the alloy's peculiarly low stacking fault energy (SFE) even at hot rolling temperatures, although the minor peaks of the near copper component were also identified. However, because of the onset of dynamic recrystallization (DRX) during the hot rolling process, the texture intensity was relatively weak even after 90% hot rolling, although the grain refinement originating from the DRX was not significant (the "less active DRX" condition increased the strain accumulation during the process, resulting in high-strength samples). The weakened texture development resulted in negligible in-plane anisotropy for the hot-rolled specimen strength, when the specimens were tensile strained in the rolling direction (RD) and transverse direction (TD). The elongation-to-failure, however, exhibited a difference with respect to the tensile loading axis. It is suggested that the ductility anisotropy is closely related to a strain-induced γ (fcc) → ε (hcp) martensitic transformation during tensile loading, resulting in a difference in the proportion of quasi-cleavage fracture surfaces. The obtained results will be helpful in the development of high-strength Co-Cr-Mo alloy plates and sheets, and have implications regarding plastic deformation and texture evolution during the hot rolling of non-conventional metallic materials with low SFE at elevated temperatures, where planar dislocation slips of Shockley partial dislocations and thermally activated process interplay.

Tuning strain-induced γ-to-ε martensitic transformation of biomedical Co-Cr-Mo alloys by introducing parent phase lattice defects

The significance of thermomechanical processing on the cellular response of biomedical Co-Cr-Mo alloys

Texture evolution and mechanical anisotropy of biomedical hot-rolled Co-Cr-Mo alloy

In-situ Investigation Via High Energy X-ray Diffraction of Stress-Induced(0002)α→(110)β Transformation in a Ti-5.5Mo-7.2Al-4.5Zr-2.6Sn-2.1Cr Alloy

Effect of grain boundary character on isothermal phase transformation and mechanical properties of Co-Cr-Mo alloy fabricated by selective laser melting

Composition-dependent slip planarity in mechanically-stable face centered cubic complex concentrated alloys and its mechanical effects

Stress-induced detwinning/reorientation of hierarchically twinned martensite and deformation micro-mechanism in Ni52Mn27Ga17Co4 shape memory alloys: Experimental and phase-field studies

In situ study of non-equilibrium solidification of CoCrFeNi high-entropy alloy and CrFeNi and CoCrNi ternary suballoys

Twin-induced transformation strengthening of CoCrNi-based medium-entropy alloy with a gradient nanostructure

In situ 3D crystallographic characterization of deformation-induced martensitic transformation in a metastable Fe–Cr–Ni austenitic alloy by X-ray microtomography

Real-time observations of TRIP-induced ultrahigh strain hardening in a dual-phase CrMnFeCoNi high-entropy alloy

Twinning Engineering of a CoCrFeMnNi High-Entropy Alloy

Stress-induced α′′ martensitic phase transformation and martensitic twinning in a metastable β titanium alloy

Microstructural evolution and mechanical properties of biomedical Co-Cr-Mo alloy subjected to high-pressure torsion

Hierarchical Grain Size and Nanotwin Gradient Microstructure for Improved Mechanical Properties of a Non-Equiatomic CoCrFeMnNi High-Entropy Alloy

The {332}<113> Twinning Behavior of a Ti-15Mo Medical Alloy during Cyclic Deformation and Its Effect on Microstructure and Performance

Transformation and twinning induced plasticity in metastable Ti-Mo alloys under high strain rate deformation

The Deformation Behavior and Microstructure Evolution of a Mn- and Cr-Containing Al-Mg-Si-Cu Alloy During Hot Compression and Subsequent Heat Treatment

Optimizing transformation-induced plasticity in CoCrNi alloys by combined grain refinement and chemical tuning

In-situ EBSD study of deformation behavior of nickel-based superalloys during uniaxial tensile tests

Effect of Multiple Reverse Transformation Treatments on Grain Refinement and Mechanical Properties of Biomedical Co–Cr–Mo–N Alloys Fabricated by Electron Beam Melting