Abstract:The main purpose of this study is to determine, via a three dimensions Finite Element analysis (FE), the stress and strain fields at the inner surface of a tubular specimen submitted to thermo-mechanical fatigue. To investigate the surface finish effect on fatigue behaviour at this inner surface, mechanical tests were carried out on real size tubular specimens under various thermal loadings. X ray measurements, Transmission Electron Microscopy observations and micro-hardness tests performed at and under the inner surface of the specimen before testing, revealed residual internal stresses and a large dislocation microstructure gradient in correlation with hardening gradients due to machining. A memory effect, bound to the pre-hardening gradient, was introduced into an elasto-visco-plastic model in order to determine the stress and strain fields at the inner surface. The temperature evolution on the inner surface of the tubular specimen was first computed via a thermo-elastic model and then used for our thermo-mechanical simulations. Identification of the thermo-mechanical model parameters was based on the experimental stabilized cyclic tension-compression tests performed at 20^{\circ}C and 300^{\circ}C. A good agreement was obtained between numerical stabilized traction-compression cycle curves (with and without pre-straining) and experimental ones. This 3 dimensional simulation gave access to the evolution of the axial and tangential internal stresses and local strains during the tests. Numerical results showed: a decreasing of the tangential stress and stabilization after 40 cycles, whereas the axial stress showed weaker decreasing with the number of cycles. The results also pointed out a ratcheting and a slightly non proportional loading at the inner surface. The computed mean stress and strain values of the stabilized cycle being far from the initial ones, they could be used to get the safety margins of standard design related to fatigue, as well as to get accurate loading conditions needed for the use of more advanced fatigue analysis and criteria.

Quantitative Model for the Prediction of the Corrosion Rate of Cold-Rolled 316L STEEL

Anomalous Evolution of Corrosion Behaviour of Warm-Rolled Type 304 Austenitic Stainless Steel

Variation In Mechanical Properties, Microstructures And Fracture Behavior Of 304 Stainless Steel During Low-Cycle Fatigue

Corrosion Prediction Models for Steel Bars in Chloride-Contaminated Concrete: a Review

The mechanoelectrochemical effect on the electrochemical corrosion of austenitic stainless steel

Experimental study on mechanical properties and low-cycle fatigue behaviour of stainless steels subjected to salt spray and dry/wet cycle

Correlation between Laboratory-Accelerated Corrosion and Field Exposure Test for High-Strength Stainless Steels

Mechanisms of Pitting Corrosion of Austenitic Steels of Heat Exchangers in Circulating Waters and its Prediction

Machine Learning-Assisted Prediction of Stress Corrosion Crack Growth Rate in Stainless Steel

Strain-rate effect and constitutive models for S31803 duplex stainless steel

Empirical model of corrosion rate for steel reinforced concrete structures in chloride-laden environments

Study on stress corrosion behavior of 316L austenitic stainless steel in hot NaOH solution

Damage-coupled unified constitutive modeling of 316LN stainless steel including dynamic strain aging under various tension dwell time: A macroscopic phenomenological study

Thermo-mechanical FE model with memory effect for 304L austenitic stainless steel presenting microstructure gradient

Effects of surface deformation on corrosive wear of stainless steel in sulfuric acid solution

The development of a mechanistic-chemometrics model with multi-degree of freedom for pitting corrosion of HP-13Cr stainless steel under extremely oilfield environments

Numerical Model for Corrosion Rate of Steel Reinforcement in Cracked Reinforced Concrete Structure

Analysis of Stress Corrosion Cracking Growth Rate in the Heat-Affected Zone of 316L Based on the Heterogeneity of the Mechanical Properties

Modeling of Hardness and Welding Residual Stress in Type 316 Stainless Steel Components for the Assessment of Stress Corrosion Cracking

Modelling and Analysis of the Corrosion Characteristics of Ferritic-Martensitic Steels in Supercritical Water

Experimental Study on the Constitutive Relation of Austenitic Stainless Steel S 31608 under Monotonic and Cyclic Loading