Abstract:The main purpose of this paper is to present the development of a new predictive model intended for the calculation of stiffness modulus |E*| determined by a four-point bending beam test (4PBB or 4PB-PR). The model developed, called model A, was based on the Witczak model, which was developed for the dynamic-modulus (DM) method. Most of the asphalt mixtures used to develop the model were high-modulus asphalt concrete (HMAC). The most commonly used methods for determining the stiffness modulus |E*| of asphalt mixtures were also discussed. The paper presents the results of the study for 10 asphalt mixtures but 8 of them were used to develop the predictive model. In addition, the results of complex shear modulus G* tests on neat and modified bituminous binders carried out in a dynamic shear rheometer (DSR), necessary for the development of a predictive model, are presented. The tests carried out in the dynamic shear rheometer had significant measurement uncertainties. The results of the volumetric parameters of the asphalt mixtures are also reported. The developed model A has maximum absolute errors e = 1930 MPa (p = 95%) and maximum relative errors re = 50% (p = 95%). The distribution of the absolute errors of the model, after discarding outliers, has a normal distribution as in the development of other models of this type, which was confirmed by appropriate statistical tests. On the basis of the tests and calculations carried out, it was concluded that, in order to increase the precision of the predictive models, it is advisable to reduce the measurement uncertainty of the bitumen complex shear modulus G*. For the developed model A, the limiting values of the stiffness modulus |E*| are also shown, within which the determined stiffness modulus should fall.

The influence of shearing forces and mass inertia on the interpretation of 4PB test results in the case of asphalt mixtures tested in two different devices

Effects of Asphalt Binder Type on Mixing Flowability and Workability Index of Asphalt Mixtures

Evaluation of Test Methods for Fracture Resistance of High Modulus Asphalt Binders from Rheological and Mechanical Perspectives

Evaluation of Complex Poisson’s Ratio of Aged Asphalt Field Cores Using Direct Tension Test and Finite Element Simulation

Three-Dimensional Discrete Element Modelling Of Influence Factors Of Indirect Tensile Strength Of Asphalt Mixtures

Comparative Study of 2D and 3D Micromechanical Discrete Element Modeling of Indirect Tensile Tests for Asphalt Mixtures

A Comparison of Two-Dimensional and Three-Dimensional Micromechanical Discrete Element Modeling of the Splitting Tests for Asphalt Mixtures

Inverse Engineering Stress-Dependent Resilient Moduli of Cement-Treated Base Materials in Asphalt Pavements Using Falling Weight Deflectometer

Improved Methodology to Evaluate Fracture Properties of Warm-Mix Asphalt Using Overlay Test

Dynamic Stiffness of Bituminous Mixtures for the Wearing Course of the Road Pavement-A Proposed Method of Measurement

Development and Analysis of High-Modulus Asphalt Concrete Predictive Model

The Impact of Dynamic Effects on the Results of Non-Destructive Falling Weight Deflectometer Testing

Cracking Analysis of Asphalt Mixture Using Semi-circle Bending Method

Laboratory Methods for Assessing the Influence of Improper Asphalt Mix Compaction on Its Performance

Numerically Supported Experimental Determination of the Behavior of the Interlayer Bond in Asphalt Pavement

Relationships Between Physical, Mechanical and Acoustic Properties of Asphalt Mixtures Using Ultrasonic Testing

Modelling of five-point bending beam test for asphalt surfacing system on orthotropic steel deck bridges

Evaluation of Asphalt Mixture Low-Temperature Performance in Bending Beam Creep Test

A spectral analysis of the dynamic frequency characteristics of asphalt pavement under live vehicle loading

Stiffness Evaluation of Laboratory and Plant Produced Foamed Bitumen Warm Asphalt Mixtures with Fiber Reinforcement and Bio-Flux Additive

Evaluation of fatigue life of high modulus asphalt concrete with use of three different definitions