Abstract:This study focuses on understanding the corrosion and tribological behaviour of hybrid aluminium composites in diverse environmental conditions (dry, aqueous and alkaline). The characteristics are compared under corrosive conditions to check the tendency to wear and corrosion for its probable use in marine applications. Eutectic aluminium–silicon (Al–Si) alloys and hybrid aluminium composites enhanced with alumina (6 wt%) and varying weights of graphene nanoplatelets (GNP) (1, 2, 3 wt%) samples were fabricated by spark plasma sintering. The corrosion behaviour of the hybrid composites was investigated by potentiodynamic polarization technique using 3.5 wt% NaCl solution as electrolyte. A chromium-plated chrome steel ball of 10-mm diameter was used for the ball-on-disk test at varying load (50–250 N), sliding velocity 0.12 m/s, sliding distance 120 m, frequency 30 Hz, stroke 2 mm, and test duration 1000 s to evaluate the tribological behaviour. An increase in the corrosion and tribological performance was observed with an increase in GNP concentration in the fabricated hybrid composite sample. Composite sample with 3 wt% of GNP had the highest average electrochemical open-circuit potential value of − 0.731 V, followed by 2 wt% (− 0.743 V), 1 wt% (− 0.747 V) and base (− 0.771 V). The presence of GNP reduced the vulnerability to corrosive degradation as being superhydrophobic, it inhibited the chloride ion attack by offering lesser adsorption of the salt solution on the hybrid composites’ surfaces. The wear mechanism was discussed by interpretation from scanning electron microscopy, energy dispersive X-ray analysis (EDX) and 3D surface profilometry. The formation of carbon protective layer at the interface led to a reduction in coefficient of friction and wear of hybrid composite with 3 wt% of GNP by more than 90% and 60%, respectively, at all environmental conditions as compared to base alloy.

Directed Energy Deposition of Aluminium Bronze/GNPs Composites: Microstructural Evolution for Enhanced Wear Resistance

Influence of graphene nanoplates and titanium diboride particulate on wear and interfacial bonding properties of sintered aluminium alloy composites

Tribological properties of Al-GNP composites at elevated temperature

Influence of T6 heat treatment on the microstructure and tribological properties of ADC12-GNPs composites

Microstructure Evolution and Properties of Graphene Nanoplatelets Reinforced Aluminum Matrix Composites

Effect of graphene addition on microstructure and wear behaviour of the A356-based composite fabricated by thixoforming process

Graphene nanoplatelets reinforced Al-Cu-Mg composite fabricated using laser powder bed fusion: microstructure, mechanical properties, and wear behaviour

Effect of Graphene on the Microstructure Evolution and Mechanical Properties of Al–10Si–2Cu–1.5Fe Aluminum Matrix Composites

Investigating the Effects of Graphene Nanoplatelets and Al4C3 on the Tribological Performance of Aluminum-Based Nanocomposites

Preparation and properties of graphene nanoplatelets reinforced aluminum composites

Enhanced Wear Resistance of Laser Cladded Graphene Nanoplatelets Reinforced Inconel 625 Superalloy Composite Coating

Corrosion and Tribo-Investigations on Alumina–Graphene-Doped Hybrid Aluminium Composites

Homogeneously Dispersed Graphene Nanoplatelets as Long-Term Corrosion Inhibitors for Aluminum Matrix Composites

Deformation-driven Metallurgy of Graphene Nanoplatelets Reinforced Aluminum Composite for the Balance Between Strength and Ductility

Wear Properties of Graphene/zirconia Biphase Nano-Reinforced Aluminium Matrix Composites Prepared by SLM

Effect of Graphene Nanoplatelet Content on Mechanical and Elevated-Temperature Tribological Performance of Self-Lubricating ZE10 Magnesium Alloy Nanocomposites

Preparation and Properties of Ni–W Composite Coatings Reinforced by Graphene Nanoplatelets

Synthesis and characterization of graphene nanoplatelets reinforced AA7068 matrix nanocomposites produced by liquid metallurgy route

High Wear Resistance and Mechanical Performance of NiAl Bronze Developed by Electron Beam Powder Bed Fusion

Enhancing Mechanical and Tribological Properties of Cold-Sprayed Aluminum Through Graphene Nanoplatelet and Boron Carbide Reinforcement

Fabrication of TiC-graphene dual-reinforced self-lubricating Al matrix hybrid nanocomposites with superior mechanical and tribological properties