Abstract:A new Powder-bed Arc Additive Manufacturing (PAAM) processing which includes on-line remelting of deposited material has been developed for the manufacturing of high entropy alloys (HEAs) based on an existing AlCoCrFeNi2.1 pseudo-eutectic system. The remelting process is typically applied in the arc melting process to improve the homogeneity of prepared material. We investigated the microstructure and mechanical properties of produced AlCoCrFeNi2.1 HEA after applying a remelting process (1, 3, and 6 times) on each deposited layer. The results show the formation of the pseudo-eutectic microstructure, which consists of relatively large columnar grains of the dominant FCC phase (similar to 90 wt%) and fine dendritic grains of the minor BCC phase (similar to 10 wt%). The applied layer-remelting process shows negligible effects on the phase fractions and their compositions, however, it significantly degraded the tensile strength and ductility of prepared alloys. Particularly, the ductility of the alloy reduced dramatically from about 27% after one time layer-remelting to only about 3% after 3 times layer remelting. This is rationalised by the significant localisation of thermally induced plasticity caused by repeated remelting of deposited material. We also show that this thermally induced plasticity leads to an increased amount of local misorientation in both constitute phases, which suggests an increased amount of stored dislocations in the microstructure. Despite the potentially strain hardening due to this accumulation of the thermally induced plasticity, the appreciable growth and constrained dendritic morphology of BCC grains that developed after remelting play a prevailing role on the materials strength, which limit the interfacial strengthening of the eutectic microstructure and consequently result in the loss of the tensile strength. The obtained results will assist in the further development and microstructure optimisation of novel HEAs using powder-based additive manufacturing processes.

Effect of plasma remelting on microstructure and properties of a CoCrCuNiAl0.5 high-entropy alloy prepared by spark plasma sintering

Enhanced Strength and Ductility in a Spark Plasma Sintered CoCrCu0·5NiAl0.5 High-Entropy Alloy Via a Double-Step Ball Milling Approach for Processing Powders

Hot cracking, crystal orientation and compressive strength of an equimolar CoCrFeMnNi high-entropy alloy printed by selective laser melting

Microstructure and mechanical properties of CoCrFeNiTa high entropy alloy prepared by mechanical alloying and spark plasma sintering

Effect of heat treatment on microstructure and mechanical properties of Al1.2CoCrFeNi2.1 high-entropy alloy fabricated by powder plasma arc additive manufacturing

Enhancing the Strength of AlCrFeNi HEAs Via Tailoring Aluminum Content and Optimal Aging Treatment

Microstructure and Properties of NiCoCrAlTi High Entropy Alloy Prepared Using MA-SPS Technique

Microstructure, Mechanical Properties, and Damping Capacity of AlxCoCrFeNi High-Entropy Alloys Prepared by Spark Plasma Sintering

Phase prediction, microstructure, and mechanical properties of spark plasma sintered Ni–Al–Ti–Mn–Co–Fe–Cr high entropy alloys

Structure and properties of Fe40Mn20Cr20Ti10Al10 high-entropy alloy fabricated by mechanical alloying and spark plasma sintering

Microstructure and Magnetic Characteristics of AlCrCuFeNiTi High-Entropy Alloy Prepared by Mechanical Alloying Followed by Spark Plasma Sintering

Effect of cold working and annealing on microstructure and properties of powder metallurgy high entropy alloy

Effect of Heat Treatment on the Microstructure and Mechanical Properties of the Al0.6CoCrFeNi High-Entropy Alloy

High-Entropy Alloy Particle Reinforced Al-Based Amorphous Alloy Composite with Ultrahigh Strength Prepared by Spark Plasma Sintering

Microstructure and mechanical properties of the TiZrNbMoTa refractory high-entropy alloy produced by mechanical alloying and spark plasma sintering

An important improvement of strength and ductility on a new type of CoCr2.5FeNi2TiW0.5 high entropy alloys under two different protective gases by selective laser melting

On the Development of Pseudo-Eutectic AlCoCrFeNi2.1 High Entropy Alloy Using Powder-bed Arc Additive Manufacturing (PAAM) Process

Microstructural evolution, mechanical and corrosion behavior of an Al7.5Co20.5Fe24Ni24Cr24 high‐entropy alloy

Microstructure Evolution and Mechanical Properties of AlCoCrFeNi2.1 Eutectic High-Entropy Alloys Processed by High-Pressure Torsion

Microstructural evolution and mechanical properties of novel nanoparticles strengthened CoCrFeNi based high entropy alloy

Atom probe tomography study of an Fe25Ni25Co25Ti15Al10 high-entropy alloy fabricated by powder metallurgy