Abstract:NiAl base eutectic alloy is an attractive material and promising to use in high temperature environment. However, the inadequate high temperature strength limits its application. In order to improve its strength, Zr was added in the Ti and Hf doped NiAl/Cr(Mo) base eutectic alloys and the effect of Zr addition on microstructure and mechanical properties of the eutectic alloy was investigated in this work. The results show that small addition of Zr can refine the NiAl/Cr(Mo) lamella inside the eutectic cell and optimize NiAl and Cr(Mo) phase morphology in the intercellular zone. Moreover, the Zr addition promotes the precipitation of bulk Heusler phase along eutectic cell boundary. With the increase of Zr addition, the eutectic cell of the alloys becomes fine, but the NiAl and Cr(Mo) phases in the intercellular zone become coarse and the Heusler phases exhibits semi-continuously distribution along the eutectic cell boundary. When the Zr content increases to 1% (atomic fraction), the NiAl and Cr(Mo) phases in eutectic cell and intercellular zone are all coarsened obviously. Additionally, coarse Cr-rich phases precipitate in the intercellular zone and Heusler phase forms the continuous network along eutectic cell boundary. The addition of Zr promotes the precipitation of coarse beta-NiAl and alpha-Cr phase in Cr(Mo) phase and NiAl phases, respectively. Moreover, the segregation of Heusler phase forming elements along the precipitate interface leads to the formation of a large number of interfacial dislocations. In addition, the addition of Zr results in the precipitation of fine Heusler particles in NiAl phase. It is shown that appropriate addition of Zr can improve the compression strength of Ni-33Al-28Cr-5.5Mo-1.0Ti-0.3Hf eutectic alloys significantly at room temperature and high temperature without reducing its compression plasticity, but more addition of Zr reduces the compressive plastic of the alloy inevitably.

Structural variation in near-eutectic zinc-aluminum alloys

Effect of Composition on Microstructural Evolution during Homogenization of 7XXX Alloys

Non-equilibrium solidification of bulk undercooled Ni–P eutectic alloys

Effect of cooling rate on α variant selection and microstructure evolution in a near β Ti–5Al–3Mo–3V–2Cr–2Zr–1Nb–1Fe alloy

Effect of Ti Addition on the Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn Alloys

Microstructure Regulation and Strength-Elongation Synergy of the Near Alpha TZAM Alloy Via Thermomechanical Processing

Effects of the cooling rate on mechanical properties and microstructure of near- α Ti-6Al-3Zr-2Nb-Mo alloy

The Effect of Cooling Rate on the Microstructure and Mechanical Properties of Mg–Zn–Gd-based Alloys

Microstructural formation and evolution of near-eutectic Al2O3–ZrO2 powders prepared by a rapid cooling technique: An exploration on coupled eutectic growth range

Coupling Effect of Undercooling and Cooling on Ti–Al–V Alloy Solidification

Effect of Cooling Rate on Solidification Structure of Zinc-Aluminum-Magnesium Alloy

EFFECT OF Zr ADDITION ON MICROSTRUCTURE AND MECHANICAL PROPERTIES OF NiAl/Cr(Mo)BASE EUTECTIC ALLOY

The Effect of Cooling Rate on Microstructure and Mechanical Properties of the Zr-4Hf-3Nb (wt%) Alloy

Characterization on the Three-Dimensional Morphology and Microstructure of Eutectics in As-Cast Mg-Gd-Y-Zr Alloys by Using X-ray Tomography Technique

Effect of copper content on thermal and mechanical properties of eutectoid zn-al alloy

Temperature-induced Structural Evolution in Liquid Sn85Zn15 Eutectic Alloy

The microstructure, fracture mechanism and their correlation with the mechanical properties of as-cast Mg-Nd-Zn-Zr alloy under the effect of cooling rate

Microstructural length scale manipulation via solidification and its influence on mechanical behavior in a high-strength intermetallic-based eutectic alloy

Influence of Zr addition on the morphology of primary MgZn 2 in the solidification microstructure of Zn-6Al-3Mg alloy

Effect of Cooling Rate on α Variant Selection and Microstructure Evolution in TB17 Titanium Alloy

Effect of cooling rate on microstructure and mechanical properties of Mg-9Gd-4Y-1Zn-1Al alloy