Abstract:PurposeThis work aims to introduce a rotating machine's defects localisation based on a time reversal method. We are interested in the study of ball bearing defects localisation by the time reversal method. Bearings are usually the most subjected components to wear in industrial rotating machines. Vibration analysis method is commonly used to investigate and extract knowledge about this type of faults as soon as they appear. This time, as a new solution, we introduced the time reversal method to this field.MethodsGenerally, the time reversal method is performed in two steps; a propagation media characterization (also known as recording step) then a localisation or focusing (back propagation step). Bearing, gears and balancing defects are some of the main defects that might occur in rotating machines. Those defects act like exterior actions which excites the machine structure. The effect of these actions follows a precise path to propagate. Thus, the first objective in this study is to characterise experimentally that path between a random position on the structure and some areas that may contain a defect. Then, apply the time reversal process to locate defected components. It has been shown in the literature that complexity of the propagation media or structure improves the efficiency of the time reversal method. Wave reflexion/conversion due to the media characteristic could add information about the source location, which is equivalent to virtual sensors. In this study case, it is due to vibrations transfer between components by contact. We propose performing a characterization step when the machine is at rest because the effect of defects occurs only if the machine is rotating. As a first investigation in this field, the interest is made on bearing defects.ResultsThe number of sensors used in the analysis can be reduced, using the time reversal method to locate defects, to a single accelerometer. The time reversal process sometimes needed combining the measurements of multiple sensors to extract the defect location. The time reversal technique makes it possible to separate the sensors from the active components. Rather than using accelerometers in the bearings, as conventionally done, the method was able to locate the fault in the structure.ConclusionThe time reversal method has a potential to be combined with other techniques to locate accurately any vibration sources in rotating machines, particularly those produced by periodic shocks.

On-Shaft Ball Bearings Monitoring By Using An Inertial Measurement Unit (Imu): Defects Severity Signatures Under Stationnary And Non-Stationary Conditions

Rolling bearing localized defect evaluation by multiscale signature via empirical mode decomposition

Smart Sensor-Based Monitoring Technology for Machinery Fault Detection

Responsiveness and Precision of Digital IMUs under Linear and Curvilinear Motion Conditions for Local Navigation and Positioning in Advanced Smart Mobility

EEMD-Based Steady-State Indexes and Their Applications to Condition Monitoring and Fault Diagnosis of Railway Axle Bearings

Highly Reliable Multicomponent MEMS Sensor for Predictive Maintenance Management of Rolling Bearings

Diagnosis Technology Investigation on High-Speed EMU Axle-box Bearings with Local Damages

Rotating Machines Health Monitoring Based on Time Reversal Method: Application to Bearings Defects Localisation

Sensor Placement and Signal Processing for Bearing Condition Monitoring

Mechanism and Method for Outer Raceway Defect Localization of Ball Bearings

CONDITION MONITORING OF LOCALIZED OUTER RACE DEFECTS OF TAPER ROLLER BEARINGS USING VIBRATION ANALYSIS

Multi-fault Detection of Rolling Element Bearings under Harsh Working Condition Using IMF-based Adaptive Envelope Order Analysis.

Optimization automating monitoring based on classification for rolling bearing

Error characteristics analysis and calibration testing for MEMS IMU gyroscope

New health indicators for the monitoring of bearing failures under variable loads

Non-stationary Signal Processing for Bearing Health Monitoring

Method for measuring non-stationary motion attitude based on MEMS-IMU array data fusion and adaptive filtering

Novel Method for Vibration Sensor-Based Instantaneous Defect Frequency Estimation for Rolling Bearings under Non-Stationary Conditions

VIBRATION ANALYSIS FOR INCIPIENT BEARING FAULT DETECCTION USING A NON-MANUAL INDEX

Advancing bearing fault diagnosis under variable working conditions: a CEEMDAN-SBS approach with vibro-electric signal integration

Evaluation of the Running Status of Ball Bearings Using Ultrasonic Signals.