Abstract:Statement of problem: Area calculation is the primary method for quantitatively analyzing accumulated plaque on the intaglio surfaces of implant-supported fixed complete dental prostheses (IFCDPs). However, the classic calculation method for stained dental plaque is based on two-dimensional (2D) photographs, which could mislead the three-dimensional (3D) representation of an object's actual morphology, especially when a surface is not flat. Purpose: This pilot in vitro study, used for methodological purposes, evaluated the repeatability and precision of a 3D area calculation method to analyze simulated accumulated biofilm on the intaglio surfaces of an IFCDP. Material and methods: The titanium framework of an IFCDP with a smooth intaglio surface was prepared with 8 milled sites and scanned by microcomputed tomography. Out of these, 4 sites were cubic (set sides lengths=1, 2, 3, and 4 mm), and 4 sites were hemispherical (set diameters=1, 2, 3, and 4 mm). A green-colored aerosol was sprayed onto the carved-out intaglio sites. The framework intaglio surface was 3D-scanned (n=10) and 2D-photographed (n=10) at 10 different photo angles. Two raters twice measured the 3D and 2D data from the carved-out sites' green-colored area one week apart. Intraobserver repeatability and interobserver reliability were evaluated with an independent t test. The deviation between the measurements and the microtomography values was calculated. Pearson's correlation coefficient (r) evaluated the repeatability of multiple measurements. A standard level of significance was set at α=.05. Results: The differences between the 2D photographs and the microtomography values were statistically significant (P<.001), whereas the differences between the 3D scans and the microtomography values were not significant (P=.063). The overall differences between the microtomography values and the 3D measurements were smaller (2.15 ±2.30 mm2 vs. 18.91 ±22.78 mm2, P=.055) than the differences between the microtomography values and the 2D measurements. The percentage differences between the microtomography values and the 3D measurements were significantly smaller (10.41 ±8.33% vs. 65.66 ±19.22%, P<.001) than the microtomography differences values with the 2D measurements. The measurement differences between the microtomography value and the 3D measured hemispherical site data were significantly smaller than the measurement differences between the microtomography values and the 3D measured cubical site data (P=.026). The 2D method had "poor" repeatability among the 10 different shot angles (r=0.391, P<.001), whereas the 3D method had "good" repeatability among the 10 scans (r=0.999, P<.001). Conclusions: An irregular intaglio surface of an IFCDP could accurately and repeatedly be recorded and analyzed by a 3D area calculation method. This color-matching assessment of the topological environment is expected to be adopted in future studies.

Applicability of Computerized Planimetric Method in Estimating Plaque Accumulation and Efficacy of a Cleaning Method for Removable Dental Prostheses

Three-dimensional macroscopical quantification of plaque accumulation on implant-supported fixed complete dental prostheses surfaces: A methodological pilot study

Agreement in quantification of removable prosthesis plaque area coverage using a semi-automated planimetric assessment method

Establishment and Evaluation of a 3D Quantitative Analysis Method for Dental Plaque Based on an Intraoral Scanner Technique.

[Evaluation of Methods for Fitness of Removable Partial Denture].

The Accuracy of a Novel 3D Digital Evaluation Method of Intraoral Fitness for Removable Partial Dentures.

Effectiveness of surface texture simulation of fixed dental prostheses by curvature analysis.

Plaque accumulation on the fitting surface of full-arch implant-supported fixed prostheses with contact or noncontact pontics: A split mouth randomized controlled trial

Evaluation of the clinical performance of different occlusal device materials

Application of Digital Impression and Model in Removable Partial Dentures for Kennedy Classⅰandⅱdentition Defects.

Comparison of an analog and digital quantitative and qualitative analysis for the fit of dental copings

Digital workflow to assess gingival recession coverage independently of the cemento-enamel Junction: a prospective clinical study using the modified coronally advanced tunnel technique with porcine dermal matrix

Effect of oral prophylactic instrumentation on the surface texture of all metal restorative materials

Digital imaging and qPCR analysis and comparison of short-term plaque removal effects of tooth brushing

Evaluation of dental plaque by quantitative digital image analysis system

Sem Evaluation Of Canal Cleanliness Following Use Of Protaper Hand-Operated Rotary Instruments And Stainless Steel K-Files

Randomised methodology development study to investigate plaque removal efficacy of manual toothbrushes

Evaluation of plaque removal by a single-headed versus a triple-headed manual toothbrush using different plaque assessment tools

Investigation on the Effectiveness of Digital Scanning Combined with Reverse Engineering Technology in Demonstrating Full Crown Tooth Preparation

Patient and Clinical Evaluation of Traditional Metal and Polyamide Removable Partial Dentures in an Elderly Cohort

Digital Protocol to Record Occlusal Analysis in Prosthodontics: A Pilot Study