Transcription factor Ets-1 is essential for mesangial matrix remodeling.

Masayuki Mizui,Yoshitaka Isaka,Yoshitsugu Takabatake,Yasufumi Sato,Hiroshi Kawachi,F. Shimizu,Shiro Takahara,Toshinori Ito,E. Imai

DOI: https://doi.org/10.1038/SJ.KI.5001541

IF: 19.6

2006-07-02

Kidney International

Abstract:

What problem does this paper attempt to address?

Simultaneously enhanced mechanical and electromagnetic interference shielding properties of steel slag-recycled carbon fiber cementitious composites via wet-grinding process

Wei Chen,Ling Li,Zhihui Lai,Xingyang He,Ying Su,Zhengqi Zheng,Bohumír Strnadel

DOI: https://doi.org/10.1617/s11527-023-02268-9

2023-11-23

Materials and Structures

Abstract:This study aims at investigating the mechanical and electromagnetic interference (EMI) shielding properties of cementitious composites with combined utilization of recycled carbon fiber (rCF) and steel slag. Different dosage of raw steel slag (SS) and wet-grinding steel slag (WSS) as replacement of cement were introduced to the cementitious composites with rCF. Wet-grinding can enhance hydration activity of SS, and also can improve the dispersibility of rCF in cement matrix thus optimizing the mechanical properties. The electrical resistivity of the composites decreases with increased WSS dosage, the conductive phase in WSS not only form new conductive pathways, but also act as bridges to connect rCFs, the WSS is more effective in lowering the electrical resistivity. The shielding effectiveness (SE) of the rCF-WSS cementitious composites increases with increased WSS dosage, which is higher than that of SS due to the higher conductivity and scattering effect of reduced particle fineness. The absorption loss SEA dominates the SET, which is mainly attributed to increasing electrical conductivity, the dielectric loss and magnetic loss also contribute to absorption loss. The synergistic effect of rCF and steel slag on electrically conductive and EMI shielding properties was demonstrated, wet-grinding process can promote the synergistic effect.

construction & building technology,materials science, multidisciplinary,engineering, civil
Lightweight Microwire/graphene/silicone Rubber Composites for Efficient Electromagnetic Interference Shielding and Low Microwave Reflectivity

Y. L. Xu,A. Uddin,D. Estevez,Y. Luo,H. X. Peng,F. X. Qin

DOI: https://doi.org/10.1016/j.compscitech.2020.108022

IF: 9.1

2020-01-01

Composites Science and Technology

Abstract:Most traditional fillers used in electromagnetic shielding composites require high loading, uniform distribution and complicated structures for modest property enhancement. Here, we propose a simple shielding system incorporating magnetic microwires M and graphene fibers G in different arrangements. Integrating both fillers in the composite resulted in superior shielding effectiveness (SE) with respect to incorporating either individual type of filler, due to improved absorption efficiency, impedance matching and polarization triggered by different arrangements of the fillers. Randomly dispersed arrays provided a maximum shielding of 6 dB for equal amount of G and M, in which polarization effects at the interface between the two regions contributed to the SE value. The highest SE of 18 dB (98.4% attenuation) was reached by the MMMGGG periodic arrays with merely 0.059 wt % filler loading enabled by the optimized arrangement and wave attenuation from the microwires dielectric/magnetic response. The normalized SE of this composite was about two to four orders of magnitude higher than that of many other shielding candidate materials. High SE, low loading, simple structure, and multifunctionality make these composites attractive for several applications. Moreover, tailoring topological and structural factors of both fillers would facilitate further SE enhancement without sacrificing the important lightweight advantage.
Modeling for the electromagnetic properties and EMI shielding of Cf/mullite composites in the gigahertz range

Xiaodong Xia,Yang Li,Lan Long,Peng Xiao,Heng Luo,Liang Pang,Xiazi Xiao,Wei Zhou

DOI: https://doi.org/10.1016/j.jeurceramsoc.2020.03.031

IF: 5.7

2020-08-01

Journal of the European Ceramic Society

Abstract:The electromagnetic properties and EMI shielding effectiveness of Cf/mullite composites via the spark plasma sintering were intensively investigated in the gigahertz range (8.2-12.4 GHz). Experimental results have revealed excellent electromagnetic properties and a high value of EMI shielding effectiveness (nearly 40 dB) for Cf/mullite composites with 1.65 vol% carbon fillers at thickness of 2 mm. We quantitatively characterize the contributions of microstructural features to overall EMI shielding effectiveness using a micromechanics-based homogenization model. The EMI shielding effectiveness enhances with respect to the Cf volume concentration before the threshold. The increasing trend of EMI shielding effectiveness with respect to AC (alternating current) frequency can be attributed to enhanced conductivity at high gigahertz range. It is demonstrated that filler and frequency dependent interface effects are essential to obtain excellent electromagnetic properties of Cf/mullite composite. The present research can provide guidances for the design of ceramic-based composites applied in high-temperature EMI shielding devices.

materials science, ceramics
Unconventional High-Value Utilization of Metallurgical Iron-Bearing Dust as Shielding Composite for Medical X-rays

Changcheng Ge,Mengge Dong,Suying Zhou,Dayu Xiao,Erjun Bu,Xianhao Lin,He Yang,Xiangxin Xue

DOI: https://doi.org/10.3390/su15086682

IF: 3.9

2023-04-14

Sustainability

Abstract:Iron-bearing dust is one of the main solid wastes in the metallurgical industry, and currently, it is mainly disposed of according to accumulation, which brings great environmental risks. Therefore, this paper proposes a method of preparing X-ray shielding materials by hot pressing using iron-bearing dust as the filler and polyimide resin powder as the matrix. A CT imaging system was used to test the X-ray shielding performance of the materials. The results demonstrated that shielding material I-95 had a shielding percentage of more than 95% at a tube voltage of 55 kVp and a tube current of 2 mA, and the thickness of the half-value layer was less than 0.68 mm. The shielding percentage and mass attenuation coefficient of the composites showed an increasing trend with increased filler addition, tube voltage, and tube current intensity, while the half-value layer thickness showed the opposite trend. Furthermore, the shielding percentage of composites with different fillers was affected by the voltage and hardly affected by the current variation. The dominant part of the shielding material interaction across the tested tube voltage range was photoelectric absorption. The prepared composite is a low-cost material and has high efficiency and is an ideal medical X-ray shielding material.

environmental sciences,environmental studies,green & sustainable science & technology
Shielding Effectiveness of CNTs/SSFs/PA6 Conductive Composites

Yang-fei Zhang,Yang Luo,Shu-lin Bai,Man Li,Zhi-yong Jia

DOI: https://doi.org/10.4028/www.scientific.net/msf.706-709.1873

2012-01-01

Materials Science Forum

Abstract:A series of carbon nanotube (CNTs) and stainless steel fiber (SSFs) filled nylon 6 (PA6) conductive composites were synthesized for electromagnetic interference (EMI) shielding applications. The materials were prepared by the melt blending method with CNTs weight fraction of 1 and 3 wt% and SSFs of 2, 4, 6, 8, 10, and 12 wt%. The shielding effectiveness, electrical resistance and crystallization behaviors were measured. The results indicate that the shielding effectiveness and electrical properties can be improved by increasing either SSFs or CNTs contents. Higher content of CNTs can bring forward the percolation threshold and enhance the shielding effectiveness to 51.8 dB. Due to the nanoconfinement/multiple nucleation effects, PA6 crystallization behavior is influenced by adding the CNTs and SSFs.
The Electromagnetic Wave Absorption Performance and Mechanical Properties of Cement-Based Composite Material Mixed with Functional Aggregates with High Fe2O3 and SiC

Zuoqun Zhang,Chaoshan Yang,Hua Cheng,Xiaohan Huang,Yuhao Zhu

DOI: https://doi.org/10.18280/rcma.310409

2021-08-31

Revue des composites et des matériaux avancés

Abstract:Now there’re many researches on the electromagnetic radiation protection function of the cement-based electromagnetic wave absorbing materials, such materials have been widely used in various types of buildings. This paper proposed an idea for preparing a cement-based composite material by mixing functional aggregates with high content of Fe2O3 and SiC, that is, adding Fe3O4 powder and nano-SiC of different contents in the clay, and then sintering at 1190°C; the prepared aggregates showed obvious magnetic loss and dielectric loss to electromagnetic waves, and the numerical tube pressure could reach 16.83MPa. The double-layer reflectivity test board made of functional aggregates showed excellent electromagnetic wave absorption performance, its reflection loss was less than -10dB in the frequency range of 8~18GHz (corresponding to energy absorption greater than 90% EM), and its maximum RL reached -12.13dB. In addition, the compressive strength of the cement-based composite material at the age of 28 days reached 50.1 MPa, which can meet the strength requirements of building materials.
High-Temperature, Lightweight Ceramics with Nano-Sized Ferrites for EMI Shielding: Synthesis, Characterisation, and Potential Applications

Vitalijs Abramovskis,Ilmars Zalite,Mikhail Maiorov,Janis Baronins,Ashish Kumar Singh,Vjaceslavs Lapkovskis,Saurav Goel,Andrei Shishkin

DOI: https://doi.org/10.3390/ma16247615

2023-12-12

Abstract:The present study focuses on the synthesis and characterisation of a lightweight ceramic material with electromagnetic interference (EMI) shielding properties, achieved using mullite containing micrometre-sized hollow spheres (cenospheres) and CoFe2O4 nanoparticles. This research explores compositions with varying CoFe2O4 contents ranging from 0 up to 20 wt.%. Conventional sintering in an air atmosphere is carried out at a temperature between 1100 and 1300 °C. The addition of ferrite nanoparticles was found to enhance the process of sintering cenospheres, resulting in improved material density and mechanical properties. Furthermore, this study reveals a direct correlation between the concentration of ferrite nanoparticles and the electromagnetic properties of the material. By increasing the concentration of ferrite nanoparticles, the electromagnetic shielding effect of the material (saturation magnetisation (Ms) and remanent magnetisation (Mr)) was observed to strengthen. These findings provide valuable insights into designing and developing lightweight ceramic materials with enhanced electromagnetic shielding capabilities. The synthesized ceramic material holds promise for various applications that require effective electromagnetic shielding, such as in the electronics, telecommunications, and aerospace industries.
Research on mechanical and electromagnetic shielding properties of cement paste with different contents of fly ash and slag

Yue Li,Yunze Liu,Caiyun Jin,Jinlei Mu,Jianglin Liu

DOI: https://doi.org/10.1016/j.ndteint.2022.102736

2022-09-17

Abstract:This paper studied the mechanical properties and electromagnetic shielding effectiveness of cement paste (CP) mixed with fly ash and slag. With pure CP as the control group, 10%, 20%, and 30% cement contents were replaced by fly ash and slag. Then the compressive and flexural strength of the samples were tested. Wet resistance and dry resistance of samples were tested by the four-probe technique. The electromagnetic shielding effectiveness of the sample in the 3.94 GHz–5.99 GHz band was tested. Finally, based on the mercury intrusion porosimetry (MIP) test and backscattered electron and energy-dispersive X-ray spectroscopy (BSE-EDS) test, the impact mechanism of fly ash and slag on the electromagnetic properties of CP was expounded from the pore structure and element distribution. The results show that with the increase of fly ash or slag, the strength of the sample decreased. Mineral admixtures had little effect on wet resistance, while dry resistance showed an increasing trend with the increase of mineral admixture content. The reflection loss had the greatest impact on electromagnetic shielding effectiveness. With the increase of mineral admixture content, the reflection loss and multiple reflection loss of the sample increased, but the absorption loss decreased. The reason for the effect of compounding different proportions of fly ash and slag on the electromagnetic shielding effectiveness of CP is mainly due to the change in the proportion of mesopores with an aperture less than 100 nm and the content of metallic elements (e. g. Fe) in the specimens.

materials science, characterization & testing
In-Situ Surface Modification of Nickel Mesh for Superior Electromagnetic Interference Shielding

Zhihang Fu,Yufeng Wu,Yunzhi Li,Kai Huang,Qingsong Li,Huiming Yao,Wanting Cao,Song Gao,Yang Qin,Zhichuan Zheng,Jianchun Xu,Ming Lei,Ke Bi,Hui Wu

DOI: https://doi.org/10.1016/j.jmat.2024.100936

IF: 8.589

2024-01-01

Journal of Materiomics

Abstract:Metal mesh, with its inherent conductivity, transparency, and flexibility, has proven to be an exceptional choice for high-performance reflection-dominated electromagnetic interference (EMI) shielding materials, due to its multifunctionality and wide applicability. However, the development of metal-based absorption-enhanced EMI shielding materials characterized by high absorption and low reflection is crucial but remains challenging. Herein, we introduce a novel surface modification strategy for nickel mesh (NM) aimed at augmenting its surface electromagnetic wave absorption through electrochemical surface microstructure alteration and subsequent wet chemical sulphuration. This approach leverages the multiple reflections within the microporous structure and the impedance matching enhancement provided by the magnetic sulfided nickel layer, resulting in the sulphur-treated porous NM (Ni3S2-PNM) achieving an outstanding average EMI SE of 59.6 dB across a broad frequency range of 4 to 40 GHz. The surface electromagnetic wave absorption rate of Ni3S2-PNM has increased from under 1% for unmodified NM to over 60%, significantly reducing the re-reflection of electromagnetic waves back into free space (the average SER value decreases from about 20 dB to 2.2 dB). Characterized by its simplicity and cost-effectiveness, this in-situ surface modification method on bulk industrial-grade NM, enhancing electromagnetic shielding, presents a promising avenue for wider application in electromagnetic protection.
Roll-to-roll Joule-heating to Construct Ferromagnetic Carbon Fiber Felt for Superior Electromagnetic Interference Shielding

Yufeng Wu,Qingsong Li,Yunzhi Li,Chang Li,Yiqian Zhou,Peng Du,Wanting Cao,Xian He,Zian Liu,Jianchun Xu,Kai Huang,Ming Lei,Ke Bi,Hui Wu

DOI: https://doi.org/10.1016/j.carbon.2024.119474

IF: 10.9

2024-01-01

Carbon

Abstract:The effective safeguard from electromagnetic radiation damage via electromagnetic interference shielding (EMI) materials is crucial for diverse applications, especially in modern aerospace, medical, and human body protection endeavors. Despite great efforts have been made to surmount challenges encompassing scalability, sustainability and cost, the integrated and continuous production of large-area electromagnetic shielding materials remains unsolved for industrial-scale demands. Herein, we develop a cascaded methodology involving spray loading and Joule-heating for fabricating hybrid EMI fabric with superior efficiency, where ferromagnetic Fe3O4 3 O 4 nano- particles are further successfully in situ deposition on ultralight carbon fiber felt (Fe3O4/FePc@CFF) 3 O 4 /FePc@CFF) in a roll-to- roll (R2R) manner. Fe3O4/FePc@CFF 3 O 4 /FePc@CFF characterized by a surface density of only 64.76 g/m2, 2 , achieves specific shielding effectiveness per unit thickness (SSE/t) remarkable values of 9604 dB cm2 2 g- 1 and 10947 dB cm2 2 g- 1 within the X-band and Ku-band, respectively. Considering the high compatibility with assembly on flow line production, this research offers substantial development potential for further design and advancement of pivotal materials in the realm of electromagnetic protection.
Cement composites with carbon fiber for electromagnetic interference shielding applications

Joohyun Lee,Hyunmin Kang,Bong Gyu Shin,Young Jae Song

DOI: https://doi.org/10.1016/j.carbon.2024.118861

IF: 10.9

2024-01-30

Carbon

Abstract:This study aims at identifying a significant inflection point of electromagnetic (EM) shielding effectiveness (SE) between the length and concentration of carbon fibers in the cement composites. Samples are prepared by mixing carbon fibers featuring lengths of 159, 409, 900, 2129, 3169, and 7299 μm with cement paste, at concentrations of 1, 2, 3, 4, and 5 wt% for all the lengths. The EM shielding performance is measured using the ASTM-D4935 method. Through the linear and exponential fitting analysis, it is verified that the optimal EM shielding performance with enough fluidity of cement composites appears at a specific concentration (2 wt%) and specific length (2 mm). Therefore, when using carbon fibers to improve the electromagnetic wave shielding performance of a building, we suggest the sweet spot of its length and content. We believe that this can provide a reference point for the realization of electromagnetic wave shielding performance above a certain level.

materials science, multidisciplinary,chemistry, physical
Influence of Conductive Filler Types on the Ratio of Reflection and Absorption Properties in Cement-Based EMI Shielding Composites

Daeik Jang,Jihoon Park,Woosuk Jang,Jinho Bang,G. M. Kim,Jaesuk Choi,Joonho Seo,Beomjoo Yang

DOI: https://doi.org/10.3390/ma17194913

IF: 3.4

2024-10-09

Materials

Abstract:The growing importance of electromagnetic interference (EMI) shielding composites in civil engineering has garnered increasing attention. Conductive cement-based composites, incorporating various conductive fillers, such as carbon nanotubes (CNTs), carbon fibers (CFs), and graphene nanoplatelets (GNPs), provide effective solutions due to their high electrical conductivity. While previous studies have primarily focused on improving the overall shielding effectiveness, this research emphasizes balancing the reflection and absorption properties. The experimental results demonstrate an EMI shielding performance exceeding 50 dB, revealing that filler size (nano, micro, or macro) and shape (platelet or fiber) significantly influence both reflection and absorption characteristics. Based on a comprehensive evaluation of the shielding properties, this study highlights the need to consider factors such as reflection versus absorption losses and filler shape or type when optimizing filler content to develop effective cement-based EMI shielding composites.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
Electromagnetic Characteristics and Microwave Absorbing Properties of a Novel Stainless Steel Powder

Jun Zhang,Xiaoying Liu,Jiangbo Huang,Hua Chen,Haochuan Wan,Ping-an Yang,Pingan Yang

DOI: https://doi.org/10.1142/s1793292024500061

2024-02-29

NANO

Abstract:Nano, Ahead of Print. In order to solve the problem of insufficient oxidation resistance and corrosion resistance of magnetic metal absorbent represented by carbonyl iron powder, a wave absorbing composite material which consists of different filling mass proportions of the atomized electrolytic stainless steel powder and paraffin wax is investigated. The electromagnetic (EM) characteristics and absorbing performance of the proposed composite material were tested with Agilent N5234A vector network analyzer in a frequency range of 2–18[math]GHz. The experimental results show that the real and imaginary parts of the dielectric permittivity of stainless steel powder/paraffin composites will increase with the filling mass fraction in the test frequency band, while the real part of the permeability [math] decreases with the increase of the mass fraction, and the imaginary part [math] increases with the increase of the mass fraction. At a thickness of 3[math]mm, with the filling mass fraction increasing from 20[math]wt.% to 60[math]wt.%, the peak frequency of reflection loss (RL) moves to low frequency from 17.92[math]GHz to 16[math]GHz. Meanwhile, the minimum reflection loss (RL[math]) also shows a downward trend, and the RL[math] value with a filling mass fraction of 60[math]wt.% is −8.93[math]dB. It can be seen that stainless steel powder shows good microwave absorbing performance, and it has excellent anti-oxidation, and anti-corrosion properties. Based on the excellent performance of stainless steel powder, its absorption performance is expected to be further improved through multi-layer optimization design, so as to meet the needs of electromagnetic protection in harsh environments.

materials science, multidisciplinary,physics, applied,nanoscience & nanotechnology
Fiber reinforced thermoplastics compounds for electromagnetic interference shielding applications

Luís C Martins,António J Pontes

DOI: https://doi.org/10.1177/07316844211051732

IF: 3.1

2021-10-20

Journal of Reinforced Plastics and Composites

Abstract:Market demands for lightweight and lower cost products drive manufacturers to improve current product portfolios. In the case of electronic devices, the most significant weight originates from the enclosure, traditionally in steel or aluminum, that ensures excellent mechanical and electromagnetic shielding performance. The use of thermoplastics filled with electrically conductive fibers, such as carbon or stainless steel, was investigated as a lightweight and cost-effective alternative to steel sheet for creating electromagnetic interference (EMI) shielding enclosures for electronic devices. This paper presents an EMI shielding analysis workflow for the development of plastic enclosures for an electronic device. The workflow starts by measuring the fiber-reinforced thermoplastic compounds shielding effectiveness (SE) with an experimental method in the 30 MHz–3 GHz frequency band. This analysis helps to filter a vast list of materials with a wide range of shielding performance, 20–100 dB, and allows to obtain empirical data for the second phase of the workflow, computer simulations. Simulations with experimentally adjusted material properties were used to validate the design concept of an enclosure in its early development phase. Results from this study showed that the selected material has better EMI SE performance than a steel sheet venting grid.

materials science, composites,polymer science
Ti3C2Tx-coated diatom frustules-derived porous SiO2 composites with high EMI shielding and mechanical properties

Sha Lyu,Te Zhao,Yanjing Wang,He Han,Tao Li,Chentao Zhang,Dandan Li,Jaw-Kai Wang,Jintao Huang,Peng Yu,Dazhi Sun

DOI: https://doi.org/10.1016/j.ceramint.2022.04.187

IF: 5.532

2022-04-01

Ceramics International

Abstract:Effective electromagnetic interference (EMI) shielding materials have garnered substantial interest for their efficacy in attenuating electromagnetic wave energy, ensuring data confidentiality, ensuring the operational stability of fragile electronic systems. To begin, artificially cultured diatom frustules (DF)-derived porous silica (DFPS) skeletons were constructed as templates in this study. Porous ceramics hot-pressed at 800 °C displayed a high compressive strength with a high specific surface area due to their three-dimensional (3D) multilayered and porous structures. Then, mechanically robust Ti3C2Tx/DFPS composites with exceptional EMI shielding performance were fabricated by immersing porous DF-based ceramics into Ti3C2Tx solutions and annealing in an argon environment to increase the materials’ shielding efficiency (SE). The EMI SE of composites hot-pressed at 800 °C achieved the maximum EMI SE of 43.2 dB in the X-band and a compressive strength of 67.5 MPa, establishing a hitherto unreported balance of mechanical characteristics and shielding performance. Prolonged transmission paths, multiple dissipation, scattering and reflection of electromagnetic energy were achieved using a well-maintained hierarchical porous silica framework decorated with MXene, with adsorption caused by surface MXene serving as the primary shielding mechanism for the composites. Due to their superior overall performance, MXene/DFPS EMI shielding composites have a bright future in the aircraft sector as delicate electronic device components.

materials science, ceramics
Fe Nanoparticles and CNTs Co-Decorated Porous Carbon/graphene Foam Composite for Excellent Electromagnetic Interference Shielding Performance

Congcong Yu,Shoupu Zhu,Chitian Xing,Xiaochun Pan,Xiaobo Zuo,Jianfei Liu,Mingliang Chen,Liwei Liu,Guanhong Tao,Qi Li

DOI: https://doi.org/10.1016/j.jallcom.2019.153108

IF: 6.2

2019-01-01

Journal of Alloys and Compounds

Abstract:In order to deal with the increasingly serious situation of electromagnetic interference (EMI), the design and development of efficient EMI shielding materials are highly desirable. This work takes advantages of metal-organic frameworks (MOFs) derived carbonaceous material and graphene foam (GF) to build an interconnected heterostructure for an ultralight and excellent EMI shielding performance material. Evenly dispersed Fe nanoparticles/carbon nanotubes (CNTs) network is in situ produced by carbonizing Fe(acac)(3) decorated Zeolitic Imidazolate Framework-8 (ZIF-8). And the composite is prepared by depositing Fe nanoparticles and CNTs co-decorated carbon matrix (FCC) on the surface of GF. This complex material with three-dimension (3D) network introduces electrical loss and magnetic loss and also results in a strong synergistic effect between FCC and GF to obviously improve the EMI shielding performance. The FCC/GF composite with polydimethylsiloxane (PDMS) obtains a significantly high total EMI shielding effectiveness (SET) of 48 dB in the X-band (8.2-12.4 GHz). Meanwhile, the density of composite is only 0.138 g/cm(3) and thus the specific EMI-SE (SSE) is up to 347.8 dB cm(3)/g. Therefore, FCC/GF has a wide range of prospects as an ultralight and efficient EMI shielding material. (C) 2019 Elsevier B.V. All rights reserved.
Lightweight Epoxy/Cotton Fiber-Based Nanocomposites with Carbon and Fe 3 O 4 for Electromagnetic Interference Shielding

Jianwei Xu,Ruiyue Chen,Zhigeng Yun,Zhongyi Bai,Kun Li,Shaozhe Shi,Junji Hou,Xiaoqin Guo,Xiaoli Zhang,Jingbo Chen

DOI: https://doi.org/10.1021/acsomega.2c01293

IF: 4.1

2022-04-20

ACS Omega

Abstract:Cotton fiber (CF)-based electroconductive papers were prepared by facile aqueous dispersion and drying processes combined with carbon nanotubes (CNTs) or graphene nanosheets (GNPs). To enhance the electromagnetic interference (EMI) shielding performance of the manufactured nanocomposites, the electroconductive papers were soaked with epoxy resin, which cooperated with the inner sprayed FeO nanoparticles. The EMI shielding effectiveness of Epoxy/CF-30-FeO-30GNPs reached 33.1 dB, of which over 85.0% is attributed to absorption, which is mainly believed to be caused by the combination of GNPs and FeO nanoparticles due to their special structures and synergetic effects. Moreover, the infiltration of epoxy between the randomly distributed loose CFs and the multiple reflections inside the interconnected networks could also help to improve the EMI shielding performance of GNP-added samples. The prepared lightweight and stiff Epoxy/CF-30-FeO-30GNP composites have promising applications in civil or military fields.

chemistry, multidisciplinary
Effect of silane-functionalized green synthesized silver nanoparticle, ferrite, and silk microfiber epoxy composite on electromagnetic interference shielding

G. Jayanthi,V. Andal,M. M.Prabaharan,P. Geetha

DOI: https://doi.org/10.1007/s10854-024-13929-y

2024-11-28

Journal of Materials Science Materials in Electronics

Abstract:This study investigates the use of ferrite and silver nanoparticle-reinforced silk microfiber composites for electromagnetic interference (EMI) shielding applications. Araldite epoxy resin served as the matrix material. Silver nanoparticles, extracted from lemon peels and silane-treated for enhanced bonding, and ferrite were used as fillers. Silk microfiber with a diameter of 6.4 microns was also incorporated. The study utilized triethylenetetramine as a catalyst and included a silane treatment process to enhance filler–matrix bonding. Silver nanoparticles, extracted from lemon peel, were treated with a 3 wt.% silane mixture, improving their interaction with the matrix. Ferrite fillers also underwent a similar silane treatment using a 90% ethanol solution and 3 wt.% 3-APTMS. The composite was fabricated using a stir casting method with a final curing process involving room temperature followed by post-curing at 110 °C. The mechanical properties of Composite E4, which contains 1 vol.% silane-treated silver nanoparticles and 1 vol.% ferrite, demonstrated superior performance with tensile strength of 141 MPa, flexural strength of 162 MPa, Shore-D hardness of 83, and izod impact of 6.9 J. Dielectric permittivity values for E4 were 6.1 at 8 GHz, 4.9 at 12 GHz, 3.9 at 16 GHz, and 2.7 at 18 GHz, reflecting improved polarization and energy management. EMI shielding effectiveness for E4 was notably high with absorption values of 16.5 dB at 8 GHz, 22.1 dB at 12 GHz, 33.1 dB at 16 GHz, and 36.4 dB at 18 GHz, and total shielding effectiveness of 33.1 dB at 8 GHz, 49.6 dB at 12 GHz, 66.2 dB at 16 GHz, and 71.7 dB at 18 GHz. Furthermore, the fiber-reinforced composite specimen E2 shows hydrophobic properties, and inclusion filler particle on composites such E3, E4, E5 shows hydrophilic properties. SEM analysis of Composite E4 revealed well-dispersed filler particles and enhanced interfacial bonding, contributing to its improved mechanical and EMI shielding performance.

engineering, electrical & electronic,materials science, multidisciplinary,physics, condensed matter, applied
Synergy of micron graphite and fly ash for alkali-activated cementitious material: Electromagnetic absorption characteristics and mechanism

Peiqi Zheng,Kaixuan Zhang,Weize Wang,Jing Wang,Xiuzhi Zhang

DOI: https://doi.org/10.1016/j.cemconcomp.2024.105513

IF: 9.93

2024-03-19

Cement and Concrete Composites

Abstract:To attain a balance between compressive strength and electromagnetic wave absorption performance, this paper combined two electromagnetic wave loss mechanisms (magnetic loss and electrical loss), and prepared an environmentally friendly alkali-activated slag/fly cementitious material (ASFC) using micron graphite (MG) as the absorber and ground granulated blast furnace slag (GGBS) and fly ash (FA) as the precursors. The conductivity, electromagnetic wave absorption characteristics and compressive strength of ASFC with different ratios of GGBS and FA, MG size (800 mesh, 320 mesh, and 100 mesh), and content were investigated. The results indicated that when the ratio of GGBS and FA was 7:3, natural resonance and eddy current loss contributed to electromagnetic waves absorption at 8.2–11.0 GHz and 11.0–15.5 GHz range respectively. Additionally, the conductivity of MG/ASFC showed typical percolation characteristics, with the percolation threshold reached at a dosage of 3 wt.%. In the 8.2–18.0 GHz, the incorporation of MG significantly augmented the conductive loss and polarization loss of ASFC. Furthermore, smaller-size MG was more beneficial for facilitating conductive loss and polarization loss of MG/ASFC among three different sizes. By adding 2 wt.% of MG with 800 mesh, MG/ASFC can achieve a minimum reflectivity of −27.8 dB with a bandwidth of 3.0 GHz (Reflectivity ˂-7 dB). However, when compared to other cement-based absorbing materials reported, the MG/ASFC prepared in this experiment demonstrated better compressive strength and wave absorption properties. This finding contributing to a better understanding of green building materials with electromagnetic radiation protection capabilities.

construction & building technology,materials science, composites
Influence of Carbon-Based Fillers on the Electromagnetic Shielding Properties of a Silicone-Potting Compound

Rafael Seidel,Konrad Katzer,Jakob Bieck,Maurice Langer,Julian Hesselbach,Michael Heilig

DOI: https://doi.org/10.3390/ma17020280

IF: 3.4

2024-01-06

Materials

Abstract:The effect of carbon-based additives on adhesives and potting compounds with regard to electrical conductivity and electromagnetic interference (EMI) shielding properties is of great interest. The increasing power of wireless systems and the ever-higher frequency bands place new demands on shielding technology. This publication gives an overview of the effect of carbon-based fillers on electrical conductivity, electromagnetic shielding properties, and the influence of different fillers and filler amounts on rheological behavior. This work focuses on carbon black (CB), recycled carbon fibers (rCF), carbon nanotubes (CNTs), and complex nanomaterials. Therefore, silicon samples with different fillers and filler amounts were prepared using a dual asymmetric centrifuge and a three-roll mill. It has been found that even with small filler amounts, the electromagnetic shielding properties were drastically raised. The filler content as well as the dispersion technique have a significant influence on most of the fillers. It has also been found that the complex viscosity is strongly influenced by the dispersion technique as well as by the choice and amount of filler. In the experiments carried out, shielding values of over 20 dB were achieved with several fillers, whereby even 43 dB were reached with complex, pre-crosslinked fillers. This signal reduction of up to 99.99% enables almost complete shielding of the related frequency.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering

Transcription factor Ets-1 is essential for mesangial matrix remodeling.

Simultaneously enhanced mechanical and electromagnetic interference shielding properties of steel slag-recycled carbon fiber cementitious composites via wet-grinding process

Lightweight Microwire/graphene/silicone Rubber Composites for Efficient Electromagnetic Interference Shielding and Low Microwave Reflectivity

Modeling for the electromagnetic properties and EMI shielding of Cf/mullite composites in the gigahertz range

Unconventional High-Value Utilization of Metallurgical Iron-Bearing Dust as Shielding Composite for Medical X-rays

Shielding Effectiveness of CNTs/SSFs/PA6 Conductive Composites

The Electromagnetic Wave Absorption Performance and Mechanical Properties of Cement-Based Composite Material Mixed with Functional Aggregates with High Fe2O3 and SiC

High-Temperature, Lightweight Ceramics with Nano-Sized Ferrites for EMI Shielding: Synthesis, Characterisation, and Potential Applications

Research on mechanical and electromagnetic shielding properties of cement paste with different contents of fly ash and slag

In-Situ Surface Modification of Nickel Mesh for Superior Electromagnetic Interference Shielding

Roll-to-roll Joule-heating to Construct Ferromagnetic Carbon Fiber Felt for Superior Electromagnetic Interference Shielding

Cement composites with carbon fiber for electromagnetic interference shielding applications

Influence of Conductive Filler Types on the Ratio of Reflection and Absorption Properties in Cement-Based EMI Shielding Composites

Electromagnetic Characteristics and Microwave Absorbing Properties of a Novel Stainless Steel Powder

Fiber reinforced thermoplastics compounds for electromagnetic interference shielding applications

Ti3C2Tx-coated diatom frustules-derived porous SiO2 composites with high EMI shielding and mechanical properties

Fe Nanoparticles and CNTs Co-Decorated Porous Carbon/graphene Foam Composite for Excellent Electromagnetic Interference Shielding Performance

Lightweight Epoxy/Cotton Fiber-Based Nanocomposites with Carbon and Fe 3 O 4 for Electromagnetic Interference Shielding

Effect of silane-functionalized green synthesized silver nanoparticle, ferrite, and silk microfiber epoxy composite on electromagnetic interference shielding

Synergy of micron graphite and fly ash for alkali-activated cementitious material: Electromagnetic absorption characteristics and mechanism

Influence of Carbon-Based Fillers on the Electromagnetic Shielding Properties of a Silicone-Potting Compound