Abstract:Neutronic, thermal-hydraulics, and solid mechanics computations were used to study the different VVER-1000 reactors' operational conditions for the steady-state and the transient state. The main objective of these studies is to investigate the safe operating conditions, which is essential in determining the reactor safety limits. The coupling between different physics enables a better understanding of reactor phenomena and enhanced accuracy by reducing the assumption needed for separate calculations for different physics. MCNPX code is used to provide the source power distribution for two themes of calculations. The first theme is the analytical solution using MATLAB software, and the second theme is the finite element coupled physics using COMSOL Multiphysics. Analytical solutions using MATLAB software and results from COMSOL-Multiphysics were used to simulate the uncoupled analytical models and coupled models, respectively. The coupled theme provide feedbacks between different physics by iterating the solution between different physics; such as solving the heat transfer with taking into consideration the variation of the coolant velocity along the coolant channel and solving solid mechanics with taking into consideration the change of either the fuel and the clad temperatures distribution (thermal load) or the change in the coolant pressure (pressure load). While in the uncoupled solutions, certain assumptions reflect an average behavior for the effect of other physics on the physics under concern, such as the average pressure of the coolant and the average value for the coolant velocity. The obtained results are verified by comparing it to WIMS D-4 for neutronic calculations and COPERA-EN code for the thermal-hydraulic analytical solution. Also, thermal-hydraulic results by both coupled and uncoupled themes are verified against results from the final safety analysis report. The Departure from Nucleate Boiling Ratio (DNBR) and the Minimum Departure from Nucleate Boiling Ratio (MDNBR) were applied for the investigation of VVER-1000 reactor safety parameters. Solid mechanics, fluid dynamics and heat transfer were used to compute the maximum stress/maximum volumetric strain acting on both fuel and cladding material. Results from both methods satisfied the limits addressed by the designer and shows a good agreement with the other published works that used WIMS D-4 for neutronic calculations and COBRA-EN code for thermal-hydraulic calculations analytically. in addition, the maximum stress occurring on the fuel and clad materials didn't exceed the yield stress. Furthermore, the fuel material displacement didn't exceed the Helium gap thickness, which means the surface contact between the fuel and the clad material is impossible that prevents the chemical interaction between both fuel and clad at 1135 K.

New fuel types for thermal reactors in LOCA conditions

Research on Compliance Between Large Break LOCA of HPR1000 and New LOCA Acceptance Criterion 10Cfr50.46c

An assessment of UO 2 and ATF concept fuel performance modeling demands against current experimental capabilities under LOCA conditions

LOFA and LOUHS analysis on the energy well SMR using TRACE code

Safety Analysis of Pressurized Water Reactors with Annular Fuel During Different Transients

Comprehensive Safety Analysis Code System for Nuclear Fusion Reactors III: Ex-Vessel LOCA Analyses Considering Passive Safety

Analysis for Fuel Rod Performance under LOCA Based on the FROBA-ROD 2.0 Code

Thermohydraulic Analysis of Accident Scenarios of a Fusion DEMO Reactor Based on Water-Cooled Ceramic Breeder Blanket: Analysis of LOCAs and LOVA

Analysis of Optimum Accident Tolerant Fuel and Cladding Behavior in Advanced Pressurized Water Reactor

Thermal-hydraulic and solid mechanics safety analysis for VVER-1000 reactor using analytical and CFD approaches

Numerical analysis of reflood heat transfer and large-break LOCA including CRUD layer thermal effects

Neutronics Analysis of VVER-1000 Core Using At-Fcm Fuel

Thermal-Hydraulic Design of High-Power-Density Annular Fuel in PWRs

Steady-State Performance Analysis of a Dual-Cladding Design for Accident Tolerance Fuel

Preliminary safety analysis of an in-vessel LOCA for the EU-DEMO WCLL blanket concept

Safety Analysis in VVER-1000 Due to Large-Break Loss-of-Coolant Accident and Station Blackout Transient Using RELAP5/SCDAPSIM/MOD3.5

Current status of materials development of nuclear fuel cladding tubes for light water reactors

Safety Analysis of Accident-tolerant Fuel During LBLOCA

Heat Transfer Effectiveness for Cooling of Canadian SCWR Fuel Assembly under the LOCA/LOECC Scenario

Safety-Related Optimization and Analyses of an Innovative Fast Reactor Concept

Modeling Axial Relocation of Fragmented Fuel During Loss of Coolant Conditions by Using ABAQUS