Abstract:Solid electrolytes (SEs) are vital for all-solid-state batteries (ASSBs) since they replace the flammable liquid electrolytes to make the ASSBs safer and compacter. 1 In order to boost the energy density of ASSBs, a practical SE is not only expected possessing high ionic conductivity, but also good compatibility with both cathode and anode to allow the use of high-voltage cathode and Li metal. 2, 3 However, most of the developed SEs show limitations on directly contact with either high-voltage cathode materials or Li metal. As such, SE modification is required to address the interfacial issues between SE and electrodes. In this work, fluorinated sulfide- and halide-based SEs are proposed to stabilize the SE/Li metal and SE/high-voltage cathode interfaces, respectively. Our results firstly show that fluorinated argyrodite Li 6 PS 5 Cl (LPSCl) can enhance the interfacial stability toward the Li metal anode. 4 The in-situ formed interface between Li and LPSCl 1−x F x are of highly fluorinated and condense, which enables ultrastable Li plating/stripping behavior over 250 hrs at a high current density of 6.37 mA cm −2 and a cutoff capacity of 5 mAh cm −2 . The Li metal treated by the LPSCl 1−x F x SE is then demonstrated to deliver good durability and rate capability in full cells. Other than anode side improvement, F is introduced into a superionic conductor Li 3 InCl 6 to widen the oxidation limit to over 6 V (vs. Li/Li + ). 5 Both experimental and computational results identify that F-containing passivating interphases are generated to contribute to the enhanced oxidation stability of Li 3 InCl 6-x F x and stabilization the surface of cathodes at high cut-off voltages. The optimized composition Li 3 InCl 4.8 F 1.2 is directly matched with bare high-voltage LiCoO 2 , enabling ASSBs to stably operate at room temperature at a cut-off voltage of 4.8 V (vs Li/Li + ). Our studies provide a new strategy of interface engineering by introducing F in SEs, realizing the good compatibility between SE and electrodes and opening up the applications of ASSBs. Re ferences Manthiram, A., Yu, X. W., Wang, S. F. Lithium battery chemistries enabled by solid-state electrolytes. Nat. Rev . Mater. 2, 1-16 (2017). Wang, C. H., Liang, J. W., Zhao, Y., Zheng, M. T., Li, X. N., Sun, X. L. All-solid-state lithium batteries enabled by sulfide electrolytes: from fundamental research to practical engineering design. Energy Environ. Sci. 14, 2577-2619 (2021). Li, J. C., Ma, C., Chi, M. F., Liang, C. D., Dudney, N. J. Solid Electrolyte: the Key for High-Voltage Lithium Batteries. Adv. Energy Mater. 5, 1401408 (2015). Zhao, F. P., et al. Ultrastable Anode Interface Achieved by Fluorinating Electrolytes for All-Solid-State Li Metal Batteries. ACS Energy Lett. 5, 1035-1043 (2020). Zhang, S. M., et al. Advanced High-Voltage All-Solid-State Li-Ion Batteries Enabled by a Dual-Halogen Solid Electrolyte. Adv. Energy Mater. 11, 2100836 (2021).

PVDF‐HFP via Localized Iodization as Interface Layer for All‐Solid–State Lithium Batteries with Li6PS5Cl Films

A Bifunctional Composite Artificial Solid Electrolyte Interphase for High Stable Solid-State Lithium Batteries

In Situ construction of PVDF/LLTO electrolyte with stable electrolyte/electrode interphase for integrated solid-state lithium batteries

In situ formed interfacial layer for all-solid-state lithium batteries with sulfide electrolyte films

PVDF-HFP/LiF Composite Interfacial Film to Enhance the Stability of Li-Metal Anodes

In-situ Formation of LiF-rich Composite Interlayer for Dendrite-Free All-Solid-state Lithium Batteries

SnF2‐Induced Multifunctional Interface‐Stabilized Li5.5PS4.5Cl1.5‐Based All‐Solid‐State Lithium Metal Batteries

Cationic Interfacial Layer toward a LiF-Enriched Interphase for Stable Li Metal Batteries

In situ Triggered Rich‐LiF/Mg Multifunctional Passivation Layer for Modifying the Anode Interface of All‐Solid‐State Lithium Metal Batteries

High-Performance Solid Lithium Metal Batteries Enabled by LiF/LiCl/LiIn Hybrid SEI via InCl3 -Driven In Situ Polymerization of 1,3-Dioxolane

PVDF-HFP layer with high porosity and polarity for high-performance lithium metal anodes in both ether and carbonate electrolytes

Efficient Nanoarchitectonics of Solid-Electrolyte-interface for High-Performance All-Solid-state Lithium Metal Batteries Via Mild Fluorination on Polyethylene Oxide

High Interfacial-Energy Interphase Promoting Safe Lithium Metal Batteries.

The construction of multifunctional solid electrolyte interlayers for stabilizing Li6PS5Cl-based all-solid-state lithium metal batteries

High Ionic Conductive, Mechanical Robust Sulfide Solid Electrolyte Films and Interface Design for All‐Solid‐State Lithium Metal Batteries

Interface Engineering Via Fluorinated Solid Electrolytes for All-Solid-State Li Batteries

Achieving Higher Critical Current Density in LGPS-Based Lithium Metal Batteries via a Synergistic Interlayer for Physical Inhibition and Chemical Scavenging of Lithium Dendrites

In Situ Formed Protective Layer: Toward a More Stable Interface between the Lithium Metal Anode and Li 6 PS 5 Cl Solid Electrolyte

Boosting the Interfacial Stability of the Li6PS5Cl Electrolyte with a Li Anode via In Situ Formation of a LiF-Rich SEI Layer and a Ductile Sulfide Composite Solid Electrolyte

SnF2-Catalyzed Lithiophilic-Lithiophobic Gradient Interface for High-Rate PEO-Based All-Solid-State Batteries

Localized High Concentration Polymer Electrolyte Enabling Room Temperature Solid-State Lithium Metal Batteries with Stable LiF-rich Interphases