Abstract:Statement of problem. The accuracy of digital scanning for complete dental arch and implant-supported complete-arch restorations has been reported. However, research addressing the accuracy of digital scanning methods for complete-arch tooth preparation is lacking. Purpose. The purpose of this in vitro study was to compare the accuracy of intraoral scanning, impression scanning, and cast scanning for complete-arch preparation.Material and methods. Maxillary and mandibular jaw typodonts with 28 teeth prepared for complete crowns were used as reference casts and digitized as reference data sets with a desktop scanner. Three digital scanning methods were applied. First, the reference casts were each scanned 10 times with an intraoral scanner to generate the intraoral scanning group data sets. Second, the reference casts were each captured 10 times by using polyvinyl siloxane impression material, and the impressions were scanned with a desktop scanner to generate the impression scanning group data sets. Third, the impressions obtained in the impression scanning group were used to make gypsum casts which were then digitized with a desktop scanner to generate the cast scanning group data sets. Accuracy was determined by trueness and precision. Three-dimensional deviations of the prepared arches and anterior and posterior segments were measured from root mean square values and depicted on color-difference maps. Differences among test groups were analyzed by using a 1-way ANOVA and the post hoc Bonferroni test for normally distributed data or the Kruskal-Wallis test with Bonferroni correction for non-normally distributed data (a=.05).Results. The trueness of the maxillary arch was significantly higher in the impression scanning group than in the cast scanning and intraoral scanning groups (P<.05), but no significant differences were found among the 3 groups of the mandibular arch (P>.05). The precision of both arches was significantly higher in the impression scanning and intraoral scanning groups than in the cast scanning group (P<.05). Color maps showed horizontal symmetrical displacement in the intraoral scanning group relative to the reference data sets and within-group unilateral distal-end distortion. Irregular arch deformations were noted in the impression scanning group, and buccal and occlusal expansion occurred in the anterior-posterior direction in the cast scanning group. Pooled data for anterior teeth indicated that the trueness was lowest in the intraoral scanning group; however, that for the maxillary anterior teeth did not differ, while that for the mandibular anterior teeth differed significantly among groups (P<.05). For the posterior teeth, deviation was the lowest in the impression scanning group, and significant differences were noted in both arches among the 3 groups (P<.05).Conclusions. Of the methods tested, impression scanning was the most accurate for the creation of a digital cast of a complete prepared arch. (J Prosthet Dent 2022;128:1001-8)

[Accuracy and reproducibility of intraoral scanning in vivo]

Influence of scan extension and starting quadrant on the accuracy of four intraoral scanners for fabricating tooth-supported crowns

Comparison of Measurements Between Intraoral Scanned Digital Model and Plaster Model

Accuracy of Impressions for Multiple Implants: A Comparative Study of Digital and Conventional Techniques

In vitro comparison of accuracy between conventional and digital impression using elastomeric materials and two intra‐oral scanning devices

Accuracy Analysis of Digital Models from Intraoral Scanners and 3D-Printed Casts in Children and Teenagers

Accuracy of Three Digital Scanning Methods for Complete-Arch Tooth Preparation: an in Vitro Comparison

In vitro comparative study between complete arch conventional implant impressions and digital implant scans with scannable pick-up impression copings

Comparing the accuracy of full-arch implant impressions using the conventional technique and digital scans with and without prefabricated landmarks in the mandible: An<i> in</i><i> vitro</i> study

Influence of intraoral conditions on the accuracy of full-arch scans by Cerec Primescan AC: an in vitro and in vivo comparison

Coordinate-based data analysis of the accuracy of five intraoral scanners for scanning completely dentate and partially edentulous mandibular arches

Accuracy of five intraoral scanners compared to indirect digitalization

Accuracy of edentulous full‐arch implant impression: An in vitro comparison between conventional impression, intraoral scan with and without splinting, and photogrammetry

Comparison of Intraoral Scanning Modes in Three Distinct Full- Arch Digital Implant Impression Scenarios: An In Vitro Study

Scanning Accuracy of 10 Intraoral Scanners for Single-crown and Three-unit Fixed Denture Preparations: an in Vitro Study.

A Comparison of Full Arch Trueness and Precision of Nine Intra-Oral Digital Scanners and Four Lab Digital Scanners

Study on precision of application of intraoral scanning digitized model into evaluation on region of gingival parenchyma in pa-tients with chronic periodontitis

Accuracy of Digital Implant Impressions Using a Novel Structured Light Scanning System Assisted by a Planar Mirror in the Edentulous Maxilla: an in Vitro Study

Evaluation of Three-Dimensional Digital Models Formulated From Direct Intra-oral Scanning of Dental Arches in Comparison With Extra-oral Scanning of Poured Dental Models in Terms of Dimensional Accuracy and Reliability

A new method for the evaluation of the accuracy of full-arch digital impressions in vitro

Influence of splinting scan bodies or incorporating three-dimensionally printed scan aids on the trueness of complete arch digital scans