Abstract:Rational design of high performance electrocatalyst towards electrochemical CO2 reduction (CO2RR) to C2 products remains a grand challenge. Herein, a heterostructured Cu@Cu0.4W0.6 catalyst was designed under the guidance of theoretical calculation towards CO2RR to C2 products and prepared by sequential reverse micro -emulsion and thermal reduction. The heterostructure of Cu@Cu0.4W0.6 catalysts were corroborated by X-ray diffraction (XRD) and transmission electron microscopy (TEM), which displayed spherical shape and a size of 15.6 +/- 0.5 nm. X-ray photoelectron spectroscopy illustrated more electron transfer from copper (Cu) to tungsten (W) in heterostructured Cu@Cu0.4W0.6 catalyst than that pure Cu0.4W0.6. The pure Cu0.4W0.6 catalyst is domi-nated by hydrogen evolution in CO2RR, while heterostructured Cu@Cu0.4W0.6 catalyst show much enhanced selectivity and activity towards C2 products, which is strongly dependent on the mass ratio of Cu to Cu0.4W0.6, ascribing to the Cu/Cu0.4W0.6 interface. Eventually, the Cu@Cu0.4W0.6 champion catalyst displays a Faradaic efficiency (FE) of 60.9% and a partial current density of 121.8 mA cm-2 at-1.0 V (vs. RHE) for C2 products in CO2RR in alkaline electrolyte. Computational studies indicated that the heterostructured Cu@Cu0.4W0.6 sup-presses hydrogen evolution and favors the production of CO and asymmetrical CO-CHO coupling, ascribing to the charge redistribution at the Cu/Cu0.4W0.6 interface. The high O affinity of W facilitates the rupture of C-O bond of *C2H3O intermediate and promotes the formation of ethylene. In-situ Raman spectroscopy revealed high surface coverage of bridging *CO and *CO-CHO intermediate for C2 products at 2660 cm-1 on Cu@Cu0.4W0.6, corroborating the CO-CHO coupling mechanism. This work highlights the importance of heterostructured Cu -based catalysts in tuning the CO2RR activity and selectivity of Cu-based materials.

Promoting Cu-catalysed CO 2 electroreduction to multicarbon products by tuning the activity of H 2 O

Modulating adsorbed hydrogen drives electrochemical CO2-to-C2 products

Enhancing CO2 Electroreduction Selectivity Toward Multicarbon Products Via Tuning the Local H2O/CO2 Molar Ratio.

Selective and stable CO 2 electroreduction at high rates via control of local H 2 O/CO 2 ratio

Promoting Water Activation via Molecular Engineering Enables Efficient Asymmetric C-C Coupling during CO 2 Electroreduction

Modulating water hydrogen bonding within a non-aqueous environment controls its reactivity in electrochemical transformations

Enhanced electroreduction of CO2 to C2+ products on heterostructured Cu/oxide electrodes

Enhancing CO 2 Electroreduction Selectivity toward Multicarbon Products via Tuning the Local H 2 O/CO 2 Molar Ratio

Molecular-Scale Insights into Electrochemical Reduction of CO 2 on Hydrophobically Modified Cu Surfaces

Water coordinated on Cu(I)-based catalysts is the oxygen source in CO2 reduction to CO

Enhanced electroreduction of CO<sub>2</sub> to C<sub>2+</sub> products on heterostructured Cu/oxide electrodes

Enhancing CO2 Electroreduction Performance Through Si-Doped CuO: Stabilization of Cu+/Cu0 Sites and Improved C2 Product Selectivity

Interfacial Water Tuning by Intermolecular Spacing for Stable CO2 Electroreduction to C2+ Products.

Promoting CO2 Electroreduction to Multi-Carbon Products by Hydrophobicity-Induced Electro-Kinetic Retardation.

Steering the Site Distance of Atomic Cu-Cu Pairs by First-Shell Halogen Coordination Boosts CO2-to-C2 Selectivity

Mg-Doped Cu Catalyst for Electroreduction of CO2 to Multicarbon Products: Lewis Acid Sites Simultaneously Promote *CO Adsorption and Water Dissociation

Theory-guided Synthesis of Heterostructured Cu@Cu0.4W0.6 Catalyst Towards Superior Electrochemical Reduction of CO2 to C2 Products

Direct Low Concentration CO2 Electroreduction to Multicarbon Products Via Rate-Determining Step Tuning

CO2Hydrogenation over Copper/ZnO Single‐Atom Catalysts: Water‐Promoted Transient Synthesis of Methanol

Constructing Cu0/Cu+ interfaces on Cu-based MOFs derivatives to promote the adsorption stability of intermediates in the process of CO2 electroreduction to C2 products

Manipulation of Oxygen Species on an Antimony-Modified Copper Surface to Tune the Product Selectivity in CO2 Electroreduction