Abstract:Background: Brushless DC motors are highly efficient motors due to their high torque to weight ratio, compact design, high speed operating capability and higher power density. Conventional Hall sensor based rotor position sensing is affected by the heating, vibration, interference and noise. Objective: The innovative, cost-effective and easily implementable sensorless techniques are essential in order to achieve high efficiency, reduced current and reduced torque pulsations. Furthermore, a delay free, high load fast startup is also an important issue. Methods: In this paper, an extensive review of various techniques based on the detection of freewheeling diode current, phase back EMF zero crossing point detection, back EMF integration method and third harmonic back EMF was done. The effect of various PWM strategies on back EMF detection were studied. Later on, the sensorless schemes based on flux linkage estimation and flux linkage increment were introduced. The load torque observers, unknown input observers, sliding mode observers, L ∞ − induced observers, H ∞ − deconvolution filter for back EMF estimation were also reviewed. As the brushless DC motors have no back EMF at starting and for back EMF based commutation, minimum speed is required for sufficient back EMF. Therefore various strategies of an open and close-loop reduced current startup have been studied to achieve effective commutation without reverse torque. Initial Position Detection (IPD) schemes, which are mostly based on saliency and current response to inductance variation, are effective where reverse torque is strictly prohibited. A detailed review of these Initial Position Detection techniques (IPD) has also been presented. Results: The detailed mathematical and graphical analysis has been presented here in order to understand the working of the state-of-the-art sensorless techniques. Conclusion: The back EMF detection using direct and indirect methods of terminal voltage filtering has the problem of delay and attenuation. PWM noise, freewheeling diode spikes and disturbance in detected back EMFs are also major drawbacks. The problems such as, parameter detuning, underestimation and overestimation, offset problem, system noise and observer gain variation, etc. limit the applicability of observer based technique. Therefore, a more robust and precise position estimation scheme is essential.

Investigation and mitigation of unbalanced hall sensor signal faults in sensored brushless DC motor drives

An Enhanced Sensorless Control Scheme for PMSM Drives Considering Self-inductance Asymmetry

An economical and simple strategy for overcoming the Hall sensor faults in three phase brushless DC motor drive

DC link current based commutation delay compensation method for sensored brushless DC motor drives

Comparative Performance Evaluation of Hall Effect Sensorless Control Options in Permanent Magnet Brushless DC Motor Drives

Analysis of Inter-Turn Short-Circuit Faults in Brushless DC Motors Based on Magnetic Leakage Flux and Back Propagation Neural Network

Fault-Tolerant Control Strategy for Hall Sensors in BLDC Motor Drive for Electric Vehicle Applications

Adaptive Sensorless Control of High Speed Surface-Mounted PMSM Drives with Inductance Estimator Based on Current Error

An Input Current Based Method for Fault Diagnosis of High Resistance Connection in BLDC Motors

DC-link current based position estimation and speed sensorless control of a BLDC motor used for electric vehicle applications

Recent Challenges and Advances in the Sensorless Commutation of Brushless DC Motors

Hall sensor fault diagnosis and compensation in Brushless DC motor drive using artificial intelligence technique

Fault diagnosis scheme for open-circuit faults in switched reluctance motor drives using fast Fourier transform algorithm with bus current detection

Fault Signature Identification for BLDC motor Drive System -A Statistical Signal Fusion Approach

A Fault-Tolerant Direct Torque Control Strategy for A Brushless Dc Motor Driven by A Single Sided Matrix Converter

Stator Inter-Turn Fault Detection in Closed-Loop Controlled Drive Based on Switching Sideband Harmonics in CMV

A Sage-Husa Prediction Algorithm-Based Approach for Correcting the Hall Sensor Position in DC Brushless Motors

Implementation of a MFAC based position sensorless drive for high speed BLDC motors with nonideal back EMF

Speed-Sensorless Control of Induction Motor Drives with A Delay-Based Frequency Estimation Method

Design and Implementation of Closed-Loop Controller with Current Sensors for Brushless DC Motor Drives

Development and Implementation of a Low Cost μC- Based Brushless DC Motor Sensorless Controller: A Practical Analysis of Hardware and Software Aspects