CONDITIONS AND REACTIONS DEFINING DYE BACTERIOSTASIS

E. W. Stearn,A. E. Stearn

DOI: https://doi.org/10.1128/jb.11.5.345-357.1926

IF: 3.2

1926-05-01

Journal of Bacteriology

Abstract:The continued study of bacterial cells from the point of view which assumes that they behave as conjugated proteins (Stearn and Stearn, 1924a and b) has led to an intensive study of the action of both basic and acid dyes in their bacteriostatic and staining reactions.

What problem does this paper attempt to address?

Action interference in simultaneous and proportional myocontrol: comparing force- and electromyography

Markus Nowak,Thomas Eiband,Eduardo Ruiz Ramírez,Claudio Castellini

DOI: https://doi.org/10.1088/1741-2552/ab7b1e

2020-03-27

Abstract:Myocontrol, that is, control of a prosthesis via muscle signals, is still a surprisingly hard problem. Recent research indicates that surface electromyography (sEMG), the traditional technique used to detect a subject's intent, could proficiently be replaced, or conjoined with, other techniques (multi-modal myocontrol), with the aim to improve both on dexterity and reliability. Objective. In this paper we present an online assessment of multi-modal sEMG and force myography (FMG) targeted at hand and wrist myocontrol. Approach. Twenty sEMG and FMG sensors in total were used to enforce simultaneous and proportional control of hand opening/closing, wrist pronation/supination and wrist flexion/extension of 12 intact subjects. Main results and Significance. We found that FMG yields in general a better performance than sEMG, and that the main drawback of the sEMG array we used is not the inability to perform a desired action, but rather action interference, that is, the undesired concurrent activation of another action. FMG, on the other hand, causes less interference.
Improving the Robustness of Human-Machine Interactive Control for Myoelectric Prosthetic Hand During Arm Position Changing

Ang Ke,Jian Huang,Jing Wang,Jiping He

DOI: https://doi.org/10.3389/fnbot.2022.853773

IF: 3.493

2022-06-08

Frontiers in Neurorobotics

Abstract:Robust classification of natural hand grasp type based on electromyography (EMG) still has some shortcomings in the practical prosthetic hand control, owing to the influence of dynamic arm position changing during hand actions. This study provided a framework for robust hand grasp type classification during dynamic arm position changes, improving both the "hardware" and "algorithm" components. In the hardware aspect, co-located synchronous EMG and force myography (FMG) signals are adopted as the multi-modal strategy. In the algorithm aspect, a sequential decision algorithm is proposed by combining the RNN-based deep learning model with a knowledge-based post-processing model. Experimental results showed that the classification accuracy of multi-modal EMG-FMG signals was increased by more than 10% compared with the EMG-only signal. Moreover, the classification accuracy of the proposed sequential decision algorithm improved the accuracy by more than 4% compared with other baseline models when using both EMG and FMG signals.

robotics,computer science, artificial intelligence,neurosciences
Training Wrist Extensor Function and Detecting Unwanted Movement Strategies in an EMG-controlled Visuomotor Task.

Mingxing Lyu,Charles Lambelet,Daniel Woolley,Xue Zhang,Weihai Chen,Xilun Ding,Roger Gassert,Nicole Wenderoth

DOI: https://doi.org/10.1109/icorr.2017.8009468

2017-01-01

Abstract:Stroke patients often suffer from severe upper limb paresis. Rehabilitation treatment typically targets motor impairments as early as possible, however, muscular contractions, particularly in the wrist and fingers, are often too weak to produce overt movements, making the initial phase of rehabilitation training difficult. Here we propose a new training tool whereby electromyographic (EMG) activity is measured in the wrist extensors and serves as a proxy of voluntary corticomotor drive. We used the Myo armband to develop a proportional EMG controller which allowed volunteers to perform a simple visuomotor task by modulating wrist extensor activity. In this preliminary study six healthy participants practiced the task for one session (144 trials), which resulted in a significant reduction of the average trial time required to move and hold a cursor in different target zones (p < 0.001, ANOVA), indicating skill learning. Additionally, we implemented an EMG based classifier to distinguish between the desired movement strategy and unwanted alternatives. Validation of the classifier indicated that accuracy for detecting rest, wrist extension and unwanted strategies was 92.5 + 6.9% (M + SD) across all participants. When performing the motor task the classification algorithm flagged 4.3 + 3.5% of the trials as 'unwanted strategies', even in healthy subjects. We also report initial feedback from a survey submitted to two chronic stroke patients to inquire about feasibility and acceptance of the general setup by patients.
Electromyography data for non-invasive naturally-controlled robotic hand prostheses

Manfredo Atzori,Arjan Gijsberts,Claudio Castellini,Barbara Caputo,Anne-Gabrielle Mittaz Hager,Simone Elsig,Giorgio Giatsidis,Franco Bassetto,Henning Müller

DOI: https://doi.org/10.1038/sdata.2014.53

2014-12-01

Scientific Data

Abstract:Recent advances in rehabilitation robotics suggest that it may be possible for hand-amputated subjects to recover at least a significant part of the lost hand functionality. The control of robotic prosthetic hands using non-invasive techniques is still a challenge in real life: myoelectric prostheses give limited control capabilities, the control is often unnatural and must be learned through long training times. Meanwhile, scientific literature results are promising but they are still far from fulfilling real-life needs. This work aims to close this gap by allowing worldwide research groups to develop and test movement recognition and force control algorithms on a benchmark scientific database. The database is targeted at studying the relationship between surface electromyography, hand kinematics and hand forces, with the final goal of developing non-invasive, naturally controlled, robotic hand prostheses. The validation section verifies that the data are similar to data acquired in real-life conditions, and that recognition of different hand tasks by applying state-of-the-art signal features and machine-learning algorithms is possible.

multidisciplinary sciences
Improved prosthetic hand control with concurrent use of myoelectric and inertial measurements

Agamemnon Krasoulis,Iris Kyranou,Mustapha Suphi Erden,Kianoush Nazarpour,Sethu Vijayakumar

DOI: https://doi.org/10.1186/s12984-017-0284-4

2017-07-11

Journal of NeuroEngineering and Rehabilitation

Abstract:BackgroundMyoelectric pattern recognition systems can decode movement intention to drive upper-limb prostheses. Despite recent advances in academic research, the commercial adoption of such systems remains low. This limitation is mainly due to the lack of classification robustness and a simultaneous requirement for a large number of electromyogram (EMG) electrodes. We propose to address these two issues by using a multi-modal approach which combines surface electromyography (sEMG) with inertial measurements (IMs) and an appropriate training data collection paradigm. We demonstrate that this can significantly improve classification performance as compared to conventional techniques exclusively based on sEMG signals.MethodsWe collected and analyzed a large dataset comprising recordings with 20 able-bodied and two amputee participants executing 40 movements. Additionally, we conducted a novel real-time prosthetic hand control experiment with 11 able-bodied subjects and an amputee by using a state-of-the-art commercial prosthetic hand. A systematic performance comparison was carried out to investigate the potential benefit of incorporating IMs in prosthetic hand control.ResultsThe inclusion of IM data improved performance significantly, by increasing classification accuracy (CA) in the offline analysis and improving completion rates (CRs) in the real-time experiment. Our findings were consistent across able-bodied and amputee subjects. Integrating the sEMG electrodes and IM sensors within a single sensor package enabled us to achieve high-level performance by using on average 4-6 sensors.ConclusionsThe results from our experiments suggest that IMs can form an excellent complimentary source signal for upper-limb myoelectric prostheses. We trust that multi-modal control solutions have the potential of improving the usability of upper-extremity prostheses in real-life applications.

engineering, biomedical,rehabilitation,neurosciences
A pilot study on the daily control capability of s-EMG prosthetic hands by amputees

Francesca Giordaniello

DOI: https://doi.org/10.48550/arXiv.1511.06001

2015-11-24

Abstract:Surface electromyography is a valid tool to gather muscular contraction signals from intact and amputated subjects. Electromyographic signals can be used to control prosthetic devices in a noninvasive way distinguishing the movements performed by the particular EMG electrodes activity. According to the literature, several algorithms have been used to control prosthetic hands through s-EMG signals. The main issue is to correctly classify the signals acquired as the movement actually performed. This work presents a study on the Support Vector Machine's performance in a short-time period, gained using two different feature representation (Mean Absolute Value and Waveform Length) of the sEMG signals. In particular, we paid close attention to the repeatability problem, that is the capability to achieve a stable and satisfactory level of accuracy in repeated experiments. Results on a limited setting are encouraging, as they show an average accuracy above 73% even in the worst case scenario.

Machine Learning,Human-Computer Interaction
Comparison between laparoscopy, ultrasonography, and computed tomography in widespread and localized liver diseases.

C. Mansi,V. Savarino,A. Picciotto,R. Testa,A. Canepa,M. Dodero,G. Celle

DOI: https://doi.org/10.1016/S0016-5107(82)73005-6

IF: 10.396

1982-05-01

Gastrointestinal Endoscopy

Abstract:
A Multimodal Bracelet to Acquire Muscular Activity and Gyroscopic Data to Study Sensor Fusion for Intent Detection

Daniel Andreas,Zhongshi Hou,Mohamad Obada Tabak,Anany Dwivedi,Philipp Beckerle

DOI: https://doi.org/10.3390/s24196214

IF: 3.9

2024-09-26

Sensors

Abstract:Researchers have attempted to control robotic hands and prostheses through biosignals but could not match the human hand. Surface electromyography records electrical muscle activity using non-invasive electrodes and has been the primary method in most studies. While surface electromyography-based hand motion decoding shows promise, it has not yet met the requirements for reliable use. Combining different sensing modalities has been shown to improve hand gesture classification accuracy. This work introduces a multimodal bracelet that integrates a 24-channel force myography system with six commercial surface electromyography sensors, each containing a six-axis inertial measurement unit. The device's functionality was tested by acquiring muscular activity with the proposed device from five participants performing five different gestures in a random order. A random forest model was then used to classify the performed gestures from the acquired signal. The results confirmed the device's functionality, making it suitable to study sensor fusion for intent detection in future studies. The results showed that combining all modalities yielded the highest classification accuracies across all participants, reaching 92.3±2.6% on average, effectively reducing misclassifications by 37% and 22% compared to using surface electromyography and force myography individually as input signals, respectively. This demonstrates the potential benefits of sensor fusion for more robust and accurate hand gesture classification and paves the way for advanced control of robotic and prosthetic hands.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation
EMG Pattern Classification to Control a Hand Orthosis for Functional Grasp Assistance after Stroke

Cassie Meeker,Sangwoo Park,Lauri Bishop,Joel Stein,Matei Ciocarlie

DOI: https://doi.org/10.48550/arXiv.1802.00373

2018-02-02

Abstract:Wearable orthoses can function both as assistive devices, which allow the user to live independently, and as rehabilitation devices, which allow the user to regain use of an impaired limb. To be fully wearable, such devices must have intuitive controls, and to improve quality of life, the device should enable the user to perform Activities of Daily Living. In this context, we explore the feasibility of using electromyography (EMG) signals to control a wearable exotendon device to enable pick and place tasks. We use an easy to don, commodity forearm EMG band with 8 sensors to create an EMG pattern classification control for an exotendon device. With this control, we are able to detect a user's intent to open, and can thus enable extension and pick and place tasks. In experiments with stroke survivors, we explore the accuracy of this control in both non-functional and functional tasks. Our results support the feasibility of developing wearable devices with intuitive controls which provide a functional context for rehabilitation.

Robotics,Human-Computer Interaction
Control Strategy for Underactuated Multi-Fingered Robot Hand Movement Using Electromyography Signal with Wearable Myo Armband

Ruthber Rodríguez Serrezuela,Roberto Sagaro Zamora,Enrique Marañón Reyes

DOI: https://doi.org/10.5772/intechopen.93767

2021-05-05

Abstract:The main goal of this research is to develop a control strategy for an underactuated robotic hand, based on surface electromyography (sEMG) signal obtained from a wireless Myo gesture armband, to distinguish six, several hand movements. The pattern recognition system is employed to analyze these gestures and consists of three main parts: segmentation, feature extraction, and classification. A series of 150 trials is carried out for each movement and it is established which was most suitable for electromyography signals that can be later used in recognition systems. A backpropagation neural network was used as a classifier. The architecture has a hidden network and six output layers. The number of neurons of the hidden network (20) was determined based on the performance in training progress. The proposed system is tested on datasets extracted from five healthy subjects. A great accuracy (94.94% correct assessment). between the experimentally values and those predicted by the artificial neural network (ANN) was achieved. In addition, kinematic analysis of the proposed underactuated hand has been carried out to verify the motion range of the joints. Simulations and experiments are carried out to verify the effectiveness of the proposed fingers mechanism and the hand prosthesis to generate grasp or postures.
ICP–MS with hexapole collision cell for isotope ratio measurements of Ca, Fe, and Se

S. Boulyga,J. Sabine Becker

DOI: https://doi.org/10.1007/s002160100851

2001-07-01

Analytical and Bioanalytical Chemistry

Abstract:
Simultaneous estimation of grip force and wrist angles by surface electromyography and acceleration signals

He Mao,Yue Zheng,Chenfei Ma,Kai Wu,Guanglin Li,Peng Fang

DOI: https://doi.org/10.1016/j.bspc.2022.104088

IF: 5.1

2023-01-01

Biomedical Signal Processing and Control

Abstract:In myoelectric control, simultaneous and proportional (SP) control of multiple degrees of freedom (DOFs) can realize a high level of dexterity. This study proposed a new control scheme that simultaneously estimates continuous grip force and wrist angles using a combination of surface electromyography (sEMG) and acceleration (ACC) signals. Four popular EMG features were utilized to study the regression accuracy. Nine intact subjects were recruited. They performed six force-position varying movements which involved simultaneous activation of four DOFs (wrist flexion/extension, ulnar/radial deviation, pronation/supination, and grip). The estimation performance was evaluated by the Pearson Correlation Coefficient (cc). The highest cc value was 92.12 ± 1.51%, 96.68 ± 1.16%, and 97.18 ± 0.69% for the sEMG-only, ACC-only, and multi-modal methods, respectively. Results indicate that the multi-modal approach can significantly improve regression accuracy of concurrent grip force and wrist angles, especially in pronation/supination. Besides, the multi-modal method showed higher robustness when the available number of sensors decreased and better generalization ability between movements. In conclusion, the proposed multi-modal approach has the potential for SP control of future hand prostheses.

engineering, biomedical
An Alternative Myoelectric Pattern Recognition Approach for the Control of Hand Prostheses: A Case Study of Use in Daily Life by a Dysmelia Subject

Enzo Mastinu,Johan Ahlberg,Eva Lendaro,Liselotte Hermansson,Bo Hakansson,Max Ortiz-Catalan

DOI: https://doi.org/10.1109/JTEHM.2018.2811458

2018-03-12

Abstract:The functionality of upper limb prostheses can be improved by intuitive control strategies that use bioelectric signals measured at the stump level. One such strategy is the decoding of motor volition via myoelectric pattern recognition (MPR), which has shown promising results in controlled environments and more recently in clinical practice. Moreover, not much has been reported about daily life implementation and real-time accuracy of these decoding algorithms. This paper introduces an alternative approach in which MPR allows intuitive control of four different grips and open/close in a multifunctional prosthetic hand. We conducted a clinical proof-of-concept in activities of daily life by constructing a self-contained, MPR-controlled, transradial prosthetic system provided with a novel user interface meant to log errors during real-time operation. The system was used for five days by a unilateral dysmelia subject whose hand had never developed, and who nevertheless learned to generate patterns of myoelectric activity, reported as intuitive, for multi-functional prosthetic control. The subject was instructed to manually log errors when they occurred via the user interface mounted on the prosthesis. This allowed the collection of information about prosthesis usage and real-time classification accuracy. The assessment of capacity for myoelectric control test was used to compare the proposed approach to the conventional prosthetic control approach, direct control. Regarding the MPR approach, the subject reported a more intuitive control when selecting the different grips, but also a higher uncertainty during proportional continuous movements. This paper represents an alternative to the conventional use of MPR, and this alternative may be particularly suitable for a certain type of amputee patients. Moreover, it represents a further validation of MPR with dysmelia cases.
Experimental evaluation of a sEMG-based control for elbow wearable assistive devices during load lifting tasks

Roberto Meattini,Gianluca Palli,Claudio Melchiorri

DOI: https://doi.org/10.1109/ICORR.2017.8009236

Abstract:In this work, a surface skin electromyography(sEMG)-based control solution for elbow wearable assistive devices during load lifting tasks is presented. The goal of the controller consists in limiting the user's muscle activity during the task execution, in such a way that the assistive device can partially compensate the load-related biceps muscle effort. Since sEMG-driven control strategies based on the estimation of the joint torques generally requires complex task- and subject-dependent training sessions for tuning the control algorithms, here a more direct control approach is proposed, based on a muscle activity error related proportional-integral action together with an double-threshold activation logic. The controller's parameters are easily set by means of a fast, online and automatic subject calibration procedure, ensuring a simple adjustability to different users. An experimental phase has been conducted in order to evaluate the sEMG-based control performance involving four healthy subjects, using as wearable assistive device a twisted string action module, which is particularly suitable for assistive applications because of its lightness and compactness. Results show that the control strategy is able to successfully limit the EMG activity of the subjects during the lifting tasks, providing preliminary outcomes and promising possibilities for the use of twisted string-based technologies to assist human joints and muscles.
A User Study Method on Healthy Participants for Assessing an Assistive Wearable Robot Utilising EMG Sensing

Cem Suulker,Alexander Greenway,Sophie Skach,Ildar Farkhatdinov,Stuart Charles Miller,Kaspar Althoefer

2024-08-01

Abstract:Hand-wearable robots, specifically exoskeletons, are designed to aid hands in daily activities, playing a crucial role in post-stroke rehabilitation and assisting the elderly. Our contribution to this field is a textile robotic glove with integrated actuators. These actuators, powered by pneumatic pressure, guide the user's hand to a desired position. Crafted from textile materials, our soft robotic glove prioritizes safety, lightweight construction, and user comfort. Utilizing the ruffles technique, integrated actuators guarantee high performance in blocking force and bending effectiveness. Here, we present a participant study confirming the effectiveness of our robotic device on a healthy participant group, exploiting EMG sensing.

Robotics
Mapping Individual Motor Unit Activity to Continuous Three-DoF Wrist Torques: Perspectives for Myoelectric Control

Chen Chen,Yang Yu,Xinjun Sheng,Jianjun Meng,Xiangyang Zhu

DOI: https://doi.org/10.1109/TNSRE.2023.3260209

Abstract:The surface electromyography (EMG) decomposition techniques provide access to motor neuron activities and have been applied to myoelectric control schemes. However, the current decomposition-based myoelectric control mainly focuses on discrete gestures or single-DoF continuous movements. In this study, we aimed to map the motor unit discharges, which were identified from high-density surface EMG, to the three degrees of freedom (DoFs) wrist movements. The 3-DoF wrist torques and high-density surface EMG signals were recorded concurrently from eight non-disabled subjects. The experimental protocol included single-DoF movements and their various combinations. We decoded the motor unit discharges from the EMG signals using a segment-wise decomposition algorithm. Then the neural features were extracted from motor unit discharges and projected to wrist torques with a multiple linear regression model. We compared the performance of two neural features (twitch model and spike counting) and two training schemes (single-DoF and multi-DoF training). On average, 145 ± 33 motor units were identified from each subject, with a pulse-to-noise ratio of 30.8 ± 4.2 dB. Both neural features exhibited high estimation accuracy of 3-DoF wrist torques, with an average [Formula: see text] of 0.76 ± 0.12 and normalized root mean square error of 11.4 ± 3.1%. These results demonstrated the efficiency of the proposed method in continuous estimation of 3-DoF wrist torques, which has the potential to advance dexterous myoelectric control based on neural information.
A Novel Myoelectric Control Scheme Supporting Synchronous Gesture Recognition and Muscle Force Estimation

Ruochen Hu,Xiang Chen,Haotian Zhang,Xu Zhang,Xun Chen

DOI: https://doi.org/10.1109/tnsre.2022.3166764

IF: 4.9

2022-01-01

IEEE Transactions on Neural Systems and Rehabilitation Engineering

Abstract:Aiming to provide feasible solutions for the realization of the robust and natural myoelectric control systems, a novel myoelectric control scheme supporting gesture recognition and muscle force estimation is proposed in this study. Eleven grasping gestures abstracted from daily life are selected as the target gesture set. The high-density surface electromyography (HD-sEMG) of the forearm flexor and the grasping force signal are collected simultaneously. The synchronous prediction of gesture category and instantaneous force is realized by the multi-task learning (MTL) technique. Especially, a post-processing algorithm based on threshold method is conducted to overcome the influence of force variation on the accuracy of gesture recognition. The experimental results show that the proposed post-processing method can decrease the classification error significantly. Specifically, the overall gesture classification error is reduced by 27 ~ 30 percent compared with not using the post-processing method; and 16 ~ 24 percent compared with using classical post-processing methods. The whole scheme can realize the synchronous gesture recognition and force estimation with 9.35 ± 11.48% gesture classification error and 0.1479 ± 0.0436 root-mean-square deviation force estimation accuracy. Meanwhile, it is feasible in different number of electrodes and well meets the real-time requirement of the EMG control system in response time delay (about 28.22 ~ 113.16ms on average). The proposed framework provides the possibility for myoelectric control supporting synchronous gesture recognition and force estimation, which can be extended and applied in the fields of myoelectric prosthesis and exoskeleton devices.

engineering, biomedical,rehabilitation
A Wireless Hand Grip Device for Motion and Force Analysis

Victor Becerra,Francisco J. Perales,Miquel Roca,José M. Buades,Margaret Miró-Julià

DOI: https://doi.org/10.3390/app11136036

2021-06-29

Applied Sciences

Abstract:A prototype portable device that allows for simultaneous hand and fingers motion and precise force measurements has been. Wireless microelectromechanical systems based on inertial and force sensors are suitable for tracking bodily measurements. In particular, they can be used for hand interaction with computer applications. Our interest is to design a multimodal wireless hand grip device that measures and evaluates this activity for ludic or medical rehabilitation purposes. The accuracy and reliability of the proposed device has been evaluated against two different commercial dynamometers (Takei model 5101 TKK, Constant 14192-709E). We introduce a testing application to provide visual feedback of all device signals. The combination of interaction forces and movements makes it possible to simulate the dynamic characteristics of the handling of a virtual object by fingers and palm in rehabilitation applications or some serious games. The combination of these above mentioned technologies and open and portable software are very useful in the design of applications for assistance and rehabilitation purposes that is the main objective of the device.
A Wearable Force Myography-Based Armband for Recognition of Upper Limb Gestures

Mustafa Ur Rehman,Kamran Shah,Izhar Ul Haq,Sajid Iqbal,Mohamed A. Ismail

DOI: https://doi.org/10.3390/s23239357

IF: 3.9

2023-11-23

Sensors

Abstract:Force myography (FMG) represents a promising alternative to surface electromyography (EMG) in the context of controlling bio-robotic hands. In this study, we built upon our prior research by introducing a novel wearable armband based on FMG technology, which integrates force-sensitive resistor (FSR) sensors housed in newly designed casings. We evaluated the sensors’ characteristics, including their load–voltage relationship and signal stability during the execution of gestures over time. Two sensor arrangements were evaluated: arrangement A, featuring sensors spaced at 4.5 cm intervals, and arrangement B, with sensors distributed evenly along the forearm. The data collection involved six participants, including three individuals with trans-radial amputations, who performed nine upper limb gestures. The prediction performance was assessed using support vector machines (SVMs) and k-nearest neighbor (KNN) algorithms for both sensor arrangments. The results revealed that the developed sensor exhibited non-linear behavior, and its sensitivity varied with the applied force. Notably, arrangement B outperformed arrangement A in classifying the nine gestures, with an average accuracy of 95.4 ± 2.1% compared to arrangement A’s 91.3 ± 2.3%. The utilization of the arrangement B armband led to a substantial increase in the average prediction accuracy, demonstrating an improvement of up to 4.5%.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation
User-Independent Hand Gesture Recognition Classification Models Using Sensor Fusion

Jose Guillermo Colli Alfaro,Ana Luisa Trejos

DOI: https://doi.org/10.3390/s22041321

IF: 3.9

2022-02-09

Sensors

Abstract:Recently, it has been proven that targeting motor impairments as early as possible while using wearable mechatronic devices for assisted therapy can improve rehabilitation outcomes. However, despite the advanced progress on control methods for wearable mechatronic devices, the need for a more natural interface that allows for better control remains. To address this issue, electromyography (EMG)-based gesture recognition systems have been studied as a potential solution for human–machine interface applications. Recent studies have focused on developing user-independent gesture recognition interfaces to reduce calibration times for new users. Unfortunately, given the stochastic nature of EMG signals, the performance of these interfaces is negatively impacted. To address this issue, this work presents a user-independent gesture classification method based on a sensor fusion technique that combines EMG data and inertial measurement unit (IMU) data. The Myo Armband was used to measure muscle activity and motion data from healthy subjects. Participants were asked to perform seven types of gestures in four different arm positions while using the Myo on their dominant limb. Data obtained from 22 participants were used to classify the gestures using three different classification methods. Overall, average classification accuracies in the range of 67.5–84.6% were obtained, with the Adaptive Least-Squares Support Vector Machine model obtaining accuracies as high as 92.9%. These results suggest that by using the proposed sensor fusion approach, it is possible to achieve a more natural interface that allows better control of wearable mechatronic devices during robot assisted therapies.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation

CONDITIONS AND REACTIONS DEFINING DYE BACTERIOSTASIS

Action interference in simultaneous and proportional myocontrol: comparing force- and electromyography

Improving the Robustness of Human-Machine Interactive Control for Myoelectric Prosthetic Hand During Arm Position Changing

Training Wrist Extensor Function and Detecting Unwanted Movement Strategies in an EMG-controlled Visuomotor Task.

Electromyography data for non-invasive naturally-controlled robotic hand prostheses

Improved prosthetic hand control with concurrent use of myoelectric and inertial measurements

A pilot study on the daily control capability of s-EMG prosthetic hands by amputees

Comparison between laparoscopy, ultrasonography, and computed tomography in widespread and localized liver diseases.

A Multimodal Bracelet to Acquire Muscular Activity and Gyroscopic Data to Study Sensor Fusion for Intent Detection

EMG Pattern Classification to Control a Hand Orthosis for Functional Grasp Assistance after Stroke

Control Strategy for Underactuated Multi-Fingered Robot Hand Movement Using Electromyography Signal with Wearable Myo Armband

ICP–MS with hexapole collision cell for isotope ratio measurements of Ca, Fe, and Se

Simultaneous estimation of grip force and wrist angles by surface electromyography and acceleration signals

An Alternative Myoelectric Pattern Recognition Approach for the Control of Hand Prostheses: A Case Study of Use in Daily Life by a Dysmelia Subject

Experimental evaluation of a sEMG-based control for elbow wearable assistive devices during load lifting tasks

A User Study Method on Healthy Participants for Assessing an Assistive Wearable Robot Utilising EMG Sensing

Mapping Individual Motor Unit Activity to Continuous Three-DoF Wrist Torques: Perspectives for Myoelectric Control

A Novel Myoelectric Control Scheme Supporting Synchronous Gesture Recognition and Muscle Force Estimation

A Wireless Hand Grip Device for Motion and Force Analysis

A Wearable Force Myography-Based Armband for Recognition of Upper Limb Gestures

User-Independent Hand Gesture Recognition Classification Models Using Sensor Fusion