Abstract:Medical-grade Ti6Al4V extra-low interstitial (ELI) alloy has widespread applications in the biomedical industry due to its excellent corrosion and wear resistance. Even though 3D printing offers geometry flexibility and rapid means of fabricating customized parts, 3D-printed parts are often plagued with defects including porosity, high residual stresses, and non-equilibrium structures. Thus, post-processing heat treatments may be required to optimize its properties for engineering applications. In this study, the effect of post-processing heat treatment on the microstructure, hardness, and wear properties of 3D-printed and conventionally produced medical-grade Ti6Al4V ELI alloy samples was investigated. In general, distinct α (alpha) lath and basket-weave lath structures with a high degree of orientation were observed within the microstructure of the as-printed samples. Heat treatment led to the growth of distinct continuous and discontinuous α-lath structures along prior β (beta) grain boundaries as well as basket-weave lath and the coalescence of V-shaped structures within the prior β-grains. The hardness of both the 3D-printed and conventionally produced samples increased after heat treatment (≥ 400 HV), regardless of the cooling rate and aging temperature. After being water quenched/aged, the 3D-printed samples at 500 °C had the highest hardness values owing to the presence of coarse V-shaped structures. Furthermore, the V-shaped structures were always harder than all other structures regardless of the heat treatment and manufacturing process used, indicating that these structures dictate the overall mechanical integrity of the material. X-ray diffraction and electron probe microanalysis indicated that the V-shaped structures are rich in aluminum and titanium content, which can form hcp α′ (AlTi3) intermetallic phases. The 3D-printed samples had higher wear resistance overall than the conventionally produced samples regardless of the heat treatment used. Aging at 500 °C led to a higher coefficient of friction after 3D printing owing to an increase in α-phases. Therefore, during heat treatment, the microstructure and properties of medical-grade Ti6Al4V ELI alloy are significantly affected by the starting microstructure, the rate of cooling below the β-transus, and aging temperature and time, regardless of the manufacturing process used.

Impact of Heat Treatment on Wear Characteristics of Solid-Lubricated Sillimanite-Ilmenite Aluminum Matrix Composite

Wear behaviour of T4 and T6 heat treated LM28 composite reinforced with ZrO2 particles by stir casting method

Microstructural Evolution, Tensile Failure, Fatigue Behavior and Wear Properties of Al2O3 Reinforced Al2014 Alloy T6 Heat Treated Metal Composites

Combined Effect of Particle Reinforcement and T6 Heat Treatment on the Compressive Deformation Behavior of an A357 Aluminum Alloy at Room Temperature and at 350 °C

Exploring tribological properties in the design and manufacturing of metal matrix composites: an investigation into the AL6061-SiC-fly ASH alloy fabricated via stir casting process

Effect of Heat Treatment on Mechanical Properties and Thermal Expansion of Al6063-SiC-Graphite, Molybdenum Disulfide Hybrid Composite

Role of ilmenite particles on high temperature wear behavior and coefficient of friction of LM30 aluminium alloy composites

Heat Treatment Behaviour of SLM-Built Titanium Matrix Composite: Microstructure and Tribological Performance

Influence of heat treatment on the microstructure, mechanical and tribological performances of particle reinforced aluminum matrix surface composite fabricated through friction stir processing

Examine the Optical and Dry Sliding Wear Characteristics of Aluminum Metal Matrix Composites Reinforced With Ilmenite/GR/SN

Effect of elevated temperatures and applied pressure on the tribological properties of LM30/sillimanite aluminium alloy composites

Heat treatment effect on the microstructure and corrosion behavior of Al-6061 alloy with influence of α-nanoalumina reinforcement in 3.5% NaCl solution

Effect of Heat Treatment on Tribological Properties of SiCp/Al–Mg–Mn–Cu Aluminum Matrix Composites

Effects of heat treatment and testing temperature on the tensile properties of Al–Cu and Al–Cu–Si based alloys

Performance analysis and mechanical behavior of aluminum metal matrix composite

The study of the effect of heat treatment on the properties of the AMg2–10%TiC and AMg6–10%TiC composite materials produced by self-propagating high-temperature synthesis

Effect of Heat Treatment on the Microstructural Evolution and Properties of 3D-Printed and Conventionally Produced Medical-Grade Ti6Al4V ELI Alloy

Importance of Al2TiO5 particle on the mechanical and wear performance of stir cast AA6061 composite using Central Composite Design

Microstructural Features and Wear Characteristics of Semi-Solid Processed A356 Aluminum Alloy

Solutionizing Temperature Effect on the Dry Sliding Wear Performance of Al-7Si-0.3Mg-3Ni Hypoeutectic Alloy

Processing of T6 heat-treated Al-12Si-0.6Mg alloy