Abstract:Introduction: Debonding of orthodontic brackets on ceramic restorations leave a rough surface which should be efficiently polished. In this study the effect of two diamond polishing systems (DPS), namely Optra Fine® (OF) and Diapol Twist® (DT) on surface roughness (SR) of feldspathic (F), lithium disilicate (LD), and translucent zirconia (TZ) ceramics assessed after bracket debonding. Materials and methods: Ninety disc-shaped specimens fabricated from F, LD, and TZ ceramics and glazed (Gl). Ten glazed specimens of 3 ceramic types served as control (C) groups (n=30). Other 60 specimens were deglazed, and after specific surface preparation according to ceramic type, upper central incisor brackets were bonded. After debonding, the remaining adhesive composite removed with tungsten carbide bur and specimens randomly assigned into 6 groups. The nine experimental groups defined as: Glazed F specimens (C), Deglazed F specimens polished with DT, Deglazed F specimens polished with OF, Glazed LD specimens (C), Deglazed LD specimens polished with DT, Deglazed LD specimens polished with OF, Glazed TZ specimens (C), Deglazed TZ specimens polished with DT, Deglazed TZ specimens polished with OF. The SR assessed quantitatively by profilometry (Ra and Rz parameter) and qualitatively by scanning electron microscopy (SEM). Quantitative data were statistically analysed using Kolmogorov-Smirnov test, two-way ANOVA and Tukey post-hoc test (α=0.05). Results: No significant difference found in SR of three glazed ceramic types (P=0.293 for Ra and P=0.473 for Rz). There was no significant difference of Ra between polished and glazed groups (P>0.05). However, difference in Rz was significant (P<0.05), and only TZ specimens could reach to the level of smoothness caused by glazing. Conclusions: Both diamond polishing systems can efficiently reduce the surface roughness, despite of ceramic type. Optra Fine® system showed a superior performance than Diapol Twist® without significant difference. Limitations: In this study only one brand of each ceramic type was investigated. This study was approved by Ethical Review Committee (IR.IAU.KHUISF.REC.1401.156).

Effect of polishing instruments and polishing regimens on surface topography and phase transformation of monolithic zirconia: An evaluation with XPS and XRD analysis

Phase transformations in yttria-partly stabilized zirconia induced by dental polishing regimes

The Influence of Surface Preparation, Chewing Simulation, and Thermal Cycling on the Phase Composition of Dental Zirconia

Effect of Low-Temperature Degradation, Ph-Cycling and Simulated Tooth Brushing on Surface Roughness, Topography, and Polish Retention of Yttrium-Stabilized Tetragonal Zirconia

Effect of different surface treatments on surface roughness, phase transformation, and biaxial flexural strength of dental zirconia

Alternative Treatments for Zirconium Oxide to Compare Commonly Used Surface Treatments to Determine Which Has the Least Effect on the Phase Transformation

Effect of Surface Treatment with Zirconium Dioxide Slurry on the Bond Strength of Resin Cement to Ultratranslucent Zirconia

A Comprehensive Review of the Surface and Chromatic Properties of Monolithic Zirconia: Evaluating the Impact of Polishing and Finishing Methods on Aesthetics and Performance

Influence of different surface finishing procedures of strength-gradient multilayered zirconia crowns on two-body wear and fracture load: Lithium silicate or leucite glazing versus polishing?

Surface roughness and optical characteristics evaluations after chairside adjustment of different zirconia types

Effect of Hydrothermal, Chemical, and Mechanical Degradation on Flexural Strength and Phase Transformation of Ground, Glazed, and Polished Zirconia

Full-contour Y-TZP ceramic surface roughness effect on synthetic hydroxyapatite wear

Comparing the effect of two polishing systems on surface roughness of feldspathic, lithium disilicate, and translucent zirconia ceramics after orthodontic bracket debonding: An in vitro study

Effect of toothbrushing on surface roughness, gloss, and topography of polished and glazed ultra‐translucent zirconia

Effect of toothbrushing with conventional and whitening dentifrices on monolithic zirconia after finishing procedures

Comparative effects of glazing versus polishing on mechanical, optical, and surface properties of zirconia ceramics with different translucencies

Effect of sintering programs and surface treatments on monolithic zirconia

Enamel wear against monolithic zirconia restorations: A meta-analysis and systematic review of in vitro studies

Influence of surface finish and residual stresses on the ageing sensitivity of biomedical grade zirconia

Effect of mastication simulation on the phase transformation of posterior 3-unit monolithic zirconia fixed dental prostheses

Influence of ultraviolet photofunctionalization on the surface characteristics of zirconia-based dental implant materials