Abstract:Masonry structures often exhibit poor seismic performance during earthquakes owing to their low material strength, structural integrity, and ductility. To address the mechanism of in-plane damage and collapse of masonry walls subjected to earthquake ground motion, three full-size brick walls, one with structural columns and two without structural columns, were designed and constructed in this experimental study to quantitatively investigate the effect of structural columns on the seismic performance of masonry walls. Quasi-static tests of masonry walls subjected to cyclic lateral loading were conducted using electrohydraulic servo actuators. The in-plane damage evolution and failure mode of the masonry walls under lateral loading were investigated. A numerical model with a novel plastic damage constitutive model of masonry was established. The accuracy of this model and the calculation results were verified by comparing them with the crack development and mechanical property curves obtained from the experiments. Based on the numerical model, a parametric analysis was conducted to investigate the influence of critical factors, such as mortar strength, vertical load, and height-to-width ratio, on the seismic performance of masonry structures. The test results showed that structural columns can effectively improve the performance of masonry structures. Properly installed structural columns can improve the peak load-bearing capacity, ductility, and energy dissipation of masonry structures. The masonry damage constitutive model used in this study could simulate the damage to masonry wall specimens well and reflect the hysteretic curves of the specimens within an acceptable range of accuracy. Thus, it provides a valuable reference for physical experiments. An appropriate mortar strength and vertical compressive stress can effectively enhance the load-bearing capacity of masonry structures within a certain range. For structural column walls. Walls with mortar strengths (average compressive strength) of 12.5 MPa, 10 MPa, 7.5 MPa, and 5 MPa showed an increase in peak bearing capacity of 26.2 %, 23.9 %, 18.5 %, and 9.4 %, respectively, compared to walls with mortar strengths (average compressive strength) of 2.5 Mpa. The aspect ratio had a significant impact on the shear load-bearing capacity of the masonry walls. An increase in the aspect ratio led to a transition from shear failure to flexural failure and a subsequent decrease in shear load-bearing capacity. For masonry walls with structural columns, increasing the diameter of the longitudinal steel in the structural columns can enhance the load-bearing capacity of the masonry wall, resulting in a significant improvement in its overall performance.

Damage Analysis of 3D Masonry Structures under Explosion Shock Waves Based on the CDEM

Simulation Of Collapse Process Of Masonry Walls Based On Expanded Discrete Element Method

Dynamic Progressive Collapse Response of Multi-Storey Frame Structures with Masonry Infills

EFFECTS OF CONCRETE MASONRY WALLS ON STRUCTURES UNDER NUCLEAR BLAST LOADINGS

Numerical simulation of autoclaved aerated concrete masonry wall subjected to close-in explosion and the structural damage assessment

Numerical Simulation Study of Progressive Collapse of Reinforced Concrete Frames with Masonry Infill Walls under Blast Loading

Computer Simulation of Dynamic Brittle Damage Process in Arch Dam Due to Blast Load

Numerical Simulation of Blast Loads and Dynamic Response of Reinforced Concrete Slab Subjected to Close-in Explosion

Damage Mechanism Of Reinforced Concrete Slab Under Internal Blast Loading

Concrete Spalling Behavior and Damage Evaluation of Concrete Members with Different Cross-sectional Properties under Contact Explosion

Damage evolution and failure mechanism of masonry walls under in-plane cyclic loading

Validation study on numerical simulation of RC response to close-in blast with a fully coupled model

Peridynamics simulations of the damage of reinforced concrete structures under radial blasting

Spallation Mechanism of RC Slabs under Contact Detonation

Multi-Scale Analysis Of Damage Process For Concrete Structures

Simulating the damage of rubble stone masonry walls using FDEM with a detailed micro-modelling approach

Numerical derivation of homogenised constitutional relation of mortar-less interlocking brick wall for dynamic response prediction

Blast response of clay brick masonry unit walls unreinforced and reinforced with polyurea elastomer

Stress Response and Damage Characteristics of Local Members of a Structure due to Tunnel Blasting Vibrations Based on the High-Order Local Modal Analysis

Slip-enhanced plastic-damage constitutive model for masonry structures

Scaling laws for the rigid-body response of masonry structures under blast loads