AGE AND DISEASE‐RELATED ALTERATIONS IN FIBRINOGEN‐EUGLOBULIN (FIBHINOLYTIC) BEHAVIOR

K. Moser,G. C. Hajjar

DOI: https://doi.org/10.1097/00000441-196605000-00006

1966-05-01

Abstract:

What problem does this paper attempt to address?

Synthesis of a Novel Silica‐Based Macroporous Polymer Containing TODGA Chelating Agent and Its Application in the Chromatographic Separation of Mo(VI) and Zr(IV) from Diethylenetriaminepentaacetic Acid

AY Zhang,YZ Wei,H Hoshi,M Kumagai

DOI: https://doi.org/10.1081/ss-200041145

IF: 2.799

2005-01-01

Separation Science and Technology

Abstract:A novel silica-based N,N,N',N'-tetraoctyl-3-oxapentane-1,5-diamide (TODGA) chelating polymeric material (TODGA/SiO2-P) was synthesized by impregnating TODGA into similar to 50 mu m of spherical SiO2-P particles for separating Mo(VI) and Zr(IV) from a HNO3 solution containing 0.05 M diethylenetriaminepentacetic acid (DTPA) in minor actinides recovery by extraction chromatography (MAREC) process. The adsorption of TODGA/SiO2-P for Mo(VI) and Zr(IV) was investigated by examining the influence of HNO3 and DTPA concentrations. It was found that HNO3 concentration from 0.3M to 9M either with or without 0.05M DTPA had a strong effect on the adsorption of Mo(VI) and Zr(IV) towards TODGA/SiO2-P. In the absence of 0.05 M DTPA, both the adsorption of Mo(VI) and Zr(IV) decreased with an increase in the concentration of HNO3 from 0.3 M to 3 M and then gradually increased. In the presence of 0.05 M DTPA, Zr(IV) showed scarcely any adsorption towards TODGA/SiO2-P below 2M HNO3 and was gradually adsorbed from 2M to 3M HNO3 while Mo(VI) showed almost noadsorption. In excess of 3 M HNO3, the adsorption curve of Mo(VI) or Zr(IV) fully overlapped with that of the absence of 0.05 M DTPA. This resulted from the dissociation of Mo(VI) or Zr(IV) from its complex with DTPA because of full protonation of DTPA in high HNO3 concentration and the strong complexation taking place simultaneously with TODGA/SiO-P. In terms of the batch experiments, the separation of Mo(VI) and Zr(IV) from a 3 M HNO3 solution containing 0.05 M DTPA was performed by employing the TODGA/SiO2-P packed column at 50 degrees C. Molybdenum(VI) was found to leak out of the column along with 3 M HNO3. Zirconium(IV) adsorbed by TODGA/SiO2-P was effectively eluted by 0.5 M2C2O4. The recovery was 101.6% for Mo(VI) and 94.8% for Zr(IV).
Properties and Mechanism of Molybdenum and Zirconium Adsorption by a Macroporous Silica‐Based Extraction Resin in the MAREC Process

AY Zhang,YZ Wei,M Kumagai

DOI: https://doi.org/10.1081/sei-120022523

2003-01-01

Solvent Extraction and Ion Exchange

Abstract:To achieve effective separation of molybdenum and zirconium in the MAREC process, the adsorption properties and mechanism of Mo(VI) and Zr(IV) with a macroporous CMPO/SiO2-P (CMPO: octyl(phenyl)N,N-diisobutylcarbamoylmethylphosphine oxide) extraction resin have been studied. By investigating the influence of the aqueous concentrations of H+ and NO3- on the adsorption of Mo(VI), the composition of complex of Mo(VI) and CMPO/SiO2-P is determined as H2MoO4.2CMPO/SiO2-P for dilute aqueous HNO3 and H2MoO3 (NO3)(2).2CMPO/SiO2-P for concentrated aqueous HNO3, respectively. Similarly, the composition of Zr(IV) and CMPO/SiO2-P is determined as ZrO(NO3)(2).2CMPO/SiO2-P or Zr(NO3)(4)(.)2CMPO/SiO2-P in 0.3-4.0 M HNO3, while ZrO2.2H(2)O.2CMPO/SiO2-P is assumed for lower HNO3 concentration. Based on the compositions of Mo(VI) and Zr(IV) with CMPO/SiO2-P and the elution behavior of Mo(VI) and Zr(IV) by using 0.05 M diethylenetriaminepentaacetic acid (DTPA) at 0.01-1.OM HNO3, a dynamic interconversion equilibrium between the complexes of Mo(VI) or Zr(lV) and CMPO/SiO2-P is demonstrated to take place in the elution process. To verify the adsorption mechanism, the adsorption and elution behavior of Mo(VI) and Zr(IV) with 0.05 M DTPA-pH 2.0 was performed from a simulated high level radioactive liquid waste (HLLW) containing Pd(II), Gd(III), Y(III), Eu(III), Sm(III), Mo(VI), and Zr(IV). The results indicate that Mo(VI) and Zr(IV) not only can be efficiently eluted with 0.05 M DTPA-pH 2.0, but also the elution efficiency is much better than that of 0.5 M H2C2O4 previously used in the MAREC process. The reverse equilibrium of complexes between Mo(VI) or Zr(IV) and CMPO/SiO2-P in high and low acidity was demonstrated, respectively.
Quantitative Assessment of Scanning Electron Microscope Defects in Uncombable‐Hair Syndrome

E. Rest,D. Fretzin

DOI: https://doi.org/10.1111/j.1525-1470.1990.tb00661.x

IF: 1.997

1990-06-01

Pediatric Dermatology

Abstract:Abstract: Uncombable‐hair syndrome is a rare disorder of scalp hair that starts early in childhood. It is characterized clinically as unruly hair and by scanning electron microscopy as longitudinally grooved hairs with a triangular cross section. Because of the controversy of inheritance and prior reports of similar changes in normal and other hair disorders, we performed a quantitative scanning electron microscopic assessment of four patients with uncombable‐hair syndrome, first‐degree relatives, and nonaffected controls. Our results indicate that longitudinal grooving of scalp hair is a common occurrence, and that for clinical changes to be apparent, approximately 50% of hairs must be affected.
Production and separation of 99mTc from cyclotron irradiated 100/naturalMo targets: a new automated module for separation of 99mTc from molybdenum targets

Malay Kanti Das,Madhusmita,Sankha Chattopadhyay,Sujata Saha Das,Luna Barua,Md. Alam Neyar,Umesh Kumar,Anirban De

DOI: https://doi.org/10.1007/s10967-016-4796-3

2016-03-19

Journal of Radioanalytical and Nuclear Chemistry

Abstract:The direct production of 99mTc through (p, 2n) reaction on natural molybdenum target and enriched 100Mo target was investigated. Separation of technetium radionuclide from the irradiated 100Mo target by a new method using Dowex-1 ion exchange resin as well as by the standard solvent extraction (methyl ethyl ketone) method was studied. An automated computer controlled module was developed based on the Dowex-1 separation methodology. The new chemical separation method recovered more than 80 % of 99mTc from the irradiated target. The recovered pertechnetate had requisite radionuclidic, radiochemical and chemical purity for the preparation of 99mTc-radiopharmaceuticals.

chemistry, inorganic & nuclear, analytical,nuclear science & technology
Molecular Modification of a Novel Macroporous Silica-Based Impregnated Polymeric Composite by Tri-N-butyl Phosphate and Its Application in the Adsorption for Some Metals Contained in a Typical Simulated HLLW.

Anyun Zhang,Chengliang Xiao,Etsushu Kuraoka,Mikio Kumagai

DOI: https://doi.org/10.1016/j.jhazmat.2007.01.056

IF: 13.6

2007-01-01

Journal of Hazardous Materials

Abstract:Using tri-n-butyl phosphate (TBP) as a molecular modifier, a novel macroporous silica-based 4,4',(5')-di-(tert-butylcyclohexano)-18-crown-6 (DtBuCH18C6) polymeric composite (DtBuCH18C6+TBP/SiO2-P) was synthesized. It was done by impregnating and immobilizing DtBuCH18C6 and TBP molecules into the pores of SiO2-P particles utilizing an advanced vacuum sucking technique. The adsorption of 10 fission and non-fission products Sr(II), Ba(II), Ru(III), Mo(VI), Na(I), K(I), Pd(II), La(III), Cs(I), and Y(III) onto (DtBuCH18C6+TBP)/SiO2-P was investigated by examining the influence of contact time and the HNO3 concentration in a range of 0.1-5.0M at 298 K. It was found that at the optimum concentration of 2.0M HNO3 (DtBuCH18C6+TBP)/SiO2-P exhibited strong adsorption ability and high selectivity for Sr(II) over all of the tested elements, which showed very weak or almost no adsorption except Ba(II). Moreover, the quantity of DtBuCH18C6 leaked from (DtBuCH18C6+TBP)/SiO2-P in 2.0M HNO3, 326.2 ppm, was obviously lower than 658.4 ppm that leaked from DtBuCH18C6/SiO2-P. This was ascribed to the effective association of DtBuCH18C6 and TBP through intermolecular interaction, i.e., hydrogen bonding. The significant reduction of DtBuCH18C6 leakage by molecular modification with TBP was achieved. It was of great benefit to application of the (DtBuCH18C6+TBP)/SiO2-P polymeric composite in chromatographic partitioning of Sr(II), one of the main heat generators, from high level liquid waste (HLLW) in reprocessing of nuclear spent fuel in MAREC process developed recently.
Bleeding evaluation of the stationary phase from a few novel macroporous silica-substrate polymeric materials used for radionuclide partitioning from HLLW in MAREC process

A. Zhang,Y. Wei,M. Kumagai

DOI: https://doi.org/10.1007/s10967-005-0842-2

2005-01-01

Journal of Radioanalytical and Nuclear Chemistry

Abstract:Summary To separate minor actinides from HLLW by extraction chromatography, a few novel silica-based di(2-ethylhexyl)phosphoric acid (HDEHP), 4,4¢,(5¢)-di(tert-butylcyclohexano)-18-crown-6 (DtBuCH18C6), octyl(phenyl)-N,N-diisobutylcarbamoylmethylphosphine oxide (CMPO), and N,N,N¢,N¢-tetraoctyl-3-oxapentane-1,5-diamide (TODGA) polymeric adsorption materials (HDEHP/SiO 2 -P, DtBuCH18C6/SiO 2 -P, CMPO/SiO 2 -P, and TODGA/SiO 2 -P) were synthesized by impregnating HDEHP, DtBuCH18C6, CMPO, and TODGA into the pores of porous SiO 2 -P particles, which were the new kind of inorganic/organic composites consisted of macroporous SiO 2 and copolymer. The bleeding behavior of these composites was investigated by examining the effect of contact time and HNO 3 concentration. It was found that in the tested HNO 3 concentration range, a noticeable quantity of DtBuCH18C6, at least 600 ppm, leaked out from DtBuCH18C6/SiO 2 -P because of the protonation of DtBuCH18C6 with hydrogen ion, while the others were lower and basically equivalent to the solubility of HDEHP, CMPO, or TODGA in corresponding acidities solutions. Based on the batch experiment, the bleeding of CMPO/SiO 2 -P and TODGA/SiO 2 -P, the main adsorbents used in MAREC process for HLLW partitioning, was evaluated by column operation in 0.01M HNO 3 and 3M HNO 3 . The quantity of CMPO leaked was ~48 ppm in 0.01M HNO 3 and ~37 ppm in 3.0M HNO 3 . The bleeding of TODGA decreased from 23.2 ppm to 7.27 ppm at the initial stage and then basically kept constant. An actual bleeding of TODGA was evaluated by the separation of Sr(II) from a 2.0M HNO 3 solution containing 5.0 . 10 -3 M of 6 typically simulated elements.
Adsorption and Chromatographic Separation of Mo(VI) and Zr(IV) Ions from a High-Concentration Oxalic Acid Solution by a Macroporous Silica-Based N,N,N′,N′-Tetraoctyl-3-Oxapentane-1,5-Diamide Polymeric Adsorbent

A Zhang,Y Wei,H Hoshi,M Kumagai

DOI: https://doi.org/10.1260/0263617042879519

2004-01-01

Adsorption Science & Technology

Abstract:To separate Mo(VI) and Zr(IV) ions from a 0.5 M oxalic acid solution and from each other, a novel macroporous silica-based N,N,N′,N′- tetraoctyl-3-oxapentane-1,5-diamide (TODGA) chelating polymeric adsorbent (TODGA/SiO 2 -P) was synthesized by introducing the TODGA molecule into ca. 50-μm diameter SiO 2 -P particles by impregnation. The adsorption of Mo(VI) and Zr(IV) ions onto TODGA/SiO 2 -P was investigated by examining the influence of nitric acid and oxalic acid concentrations. It was found that the adsorption was strongly affected by increasing the HNO 3 concentration from 0.5 M to 9.0 M either with or without the addition of 0.5 M H 2 C 2 O 4 . In the absence of 0.5 M H 2 C 2 O 4 , the distribution coefficients (K d ) of both Mo(VI) and Zr(IV) ions decreased with an increase in the HNO 3 concentration from 0.5 M to 3.0 M, increased slowly when the concentration of HNO 3 was increased further from 3.0 M to 6.0 M, and then increased gradually above 6.0 M concentration. Furthermore, the adsorption of Zn(IV) ions onto TODGA/SiO 2 -P was considerably greater than that of Mo(VI) ions. In the presence of 0.5 M H 2 C 2 O 4 , Zr(IV) ions showed no adsorption at HNO 3 concentrations below 4.0 M, being partly adsorbed in the presence of 4.0–6.0 M HNO 3 and fully adsorbed when the HNO 3 concentration was greater than 6.0 M. In contrast, Mo(VI) ions showed a much lower adsorption at HNO 3 concentrations below 2.0 M and no adsorption above this acid level. In the presence of HNO 3 at a concentration above 6.0 M and containing 0.5 M H 2 C 2 O 4 , the adsorption of Zr(IV) ions overlapped that from a similar HNO 3 solution which did not include 0.5 M H 2 C 2 O 4 . This was attributed to complete protonation of the C 2 O 2− 2 anion. On the basis of batch experiments, Mo(VI) and Zr(IV) ions were separated from a 6.5 M HNO 3 solution containing 0.5 M H 2 C 2 O 4 by means of a column packed with TODGA/SiO 2 -P at 50°C. The separate components, Mo(VI) and Zr(IV), could be effectively separated from each other by eluting with some selected eluants. The recovery percentage was 100.5% for Mo(VI) ions and 96.8% for Zr(IV) ions.
Simple separation of technetium from molybdenum for tracer isotope production

Kmak, Kelly N.

DOI: https://doi.org/10.1007/s10967-024-09506-6

2024-05-10

Journal of Radioanalytical and Nuclear Chemistry

Abstract:A procedure for the separation of technetium isotopes from bulk molybdenum was developed in nitric acid media. After irradiation of nat Mo foils, and dissolution in H 2 O 2 , the solution is acidified to 2 M HNO 3, and anion exchange resin is used to separate technetium from molybdenum. The procedure is simple, requiring only basic laboratory equipment and, with a two-column separation, the technetium yield is high (~ 85%) with extremely high purity (< 0.1 ppm nat Mo). This is ideally suited for laboratory production of technetium tracer isotopes, particularly 95m Tc.

chemistry, inorganic & nuclear, analytical,nuclear science & technology
Nicorandil-induced severe oral ulceration.

E. O'Sullivan

Abstract:Nicorandil has been shown to precipitate persistent ulcerative stomatitis in a small percentage of patients. To date over 50 cases have been reported, initially in France and, more recently, in the United Kingdom and Portugal, but this is the first report of nicorandil-induced ulceration in Irish medical or dental literature. It has been suggested that a previous history of aphthous ulceration may predispose the development of nicorandil-induced ulcers, although onlyone of these patients reported a history of recurrent oral ulceration (ROU).
Water extraction of technetium-99m from neutron irradiated porous molybdenum dioxide pellet

Hu, Xiangrong

DOI: https://doi.org/10.1007/s10967-024-09529-z

2024-05-16

Journal of Radioanalytical and Nuclear Chemistry

Abstract:We have been developing a novel 99 Mo/ 99m Tc generator production method using a water-insoluble porous MoO 2 target. In this method, the extraction of 99m Tc from MoO 2 is achieved by leveraging the difference in their water solubilities. The fabrication of a porous MoO 2 pellet, and the water extraction of 99m Tc from neutron irradiated porous MoO 2 were conducted. The results confirmed 99m Tc extraction with a low Mo/Tc ratio. Additionally, the dissolution rate of radioactive 99 Mo was found to be higher than stable isotopes of molybdenum, i.e., confirming the hot atom effect on the dissolution of molybdenum in (n, ) reaction.

chemistry, inorganic & nuclear, analytical,nuclear science & technology
Extraction of pertechnetate and perrhenate from water with deep-cavity [CpFe(arene)](+)-derivatized cyclotriveratrylenes

James A Gawenis,K Travis Holman,Jerry L Atwood,Silvia S Jurisson

DOI: https://doi.org/10.1021/ic0202312

2002-11-18

Abstract:Technetium-99 (beta-, t(1/2) = 2.15 x 10(5) years) is produced in a 6% fission yield from fission reactors. Technetium-99 continues to be of major concern at various nuclear sites because of its mobility in its most common chemical form during the reprocessing cycle and in the environment. Under these oxic aqueous environments the chemical form of Tc is typically Tc(VII)O4-, which is difficult to remove. Methods for pertechnetate removal to date have mixed results and pose further environmental concerns. Utilization of new cyclotriveratrylene host materials for the extraction of pertechnetate from 0.9% saline into nitromethane has shown high selectivity and efficiency. A deep-cavity host, tris[cyclopentadienyliron(II) arene]cyclotriguiasylene (2), has shown >95% extraction of pertechnetate and perrhenate into nitromethane from saline in the presence of competing anions, outperforming previously reported materials.
Adsorption and separation of terbium(III) and gadolinium(III) from aqueous nitrate medium using solid extractant

H.A. Madbouly,N.E. El-Hefny,Y.A. El-Nadi

DOI: https://doi.org/10.1080/01496395.2018.1563614

IF: 2.799

2019-01-22

Separation Science and Technology

Abstract:A macroporous copolymer of styrene and divinylbenzene resin (TVEX-PHOR) was examined for adsorption of terbium(III) and gadolinium(III) from nitrate medium. Characterization of TVEX-PHOR before and after adsorption was investigated. Different factors affecting the sorption equilibrium were studied and a maximum separation value of 2.31 was reached at V/m = 0.3 L/g. Adsorption kinetics data indicated that the pseudo-second-order model is more applicable, while the isothermal data were found to be correlated with Freundlich model. The resin uptake capacity towards Tb(III) (24.93 mg/g) was more than that of Gd(III) (15.49 mg/g). Thermodynamic parameters of sorption indicated that the process was spontaneous and exothermic.

engineering, chemical,chemistry, multidisciplinary
Preparation and characterization of a mesoporous silica-based copolymer loaded with bis(2-ethylhexyl) phosphate for the efficient separation of trace radium from natural thorium

Lifeng Chen,Xuexiang He,Linyuan Liao,Jing Tang,Lidan Lv,Dongqiao He,Xiangbiao Yin,Wenlong Li,Yuezhou Wei,Shunyan Ning

DOI: https://doi.org/10.26434/chemrxiv-2024-0rwww

2024-02-27

Abstract:Targeted α-nuclide therapy (TAT) has attracted significant attention in recent years due to its unique advantages in cancer treatment. As one of the most important TAT nuclides, 212Pb is quite rare and strongly depends on the supply of its parent nuclides with an appropriate half-life, such as 228Ra or 224Ra. Therefore, establishing a stable and effective method to obtain these nuclides is critical. To address this issue, a silica-supported copolymer loaded with bis (2-ethylhexyl) phosphate (HDEHP) was prepared, characterized, and investigated for the separation of 228Ra and 224Ra from natural 232Th in the nitric acid media. The experimental results showed that the adsorbent was prepared successfully with 19.5 wt% HDEHP loading, and possessed a small particle size and a porous structure. Compared with traditional cation exchange resin, the adsorbent exhibited ultrahigh selectivity and ultrafast adsorption kinetics towards thorium, with the equilibrium time less than 3 min. The adsorption isotherm was well described by the Langmuir model, and the maximum adsorption amount towards thorium could reach 72.0 mg/g. Thermodynamic investigations suggested that the thorium adsorption was endothermic and spontaneous. On basis of batch experiments, the separation behaviors were further investigated in column modes, and the separation of 228Ra and 224Ra from thorium was finally demonstrated using 226Ra as the tracer nuclide. The chemical recovery rate to 226Ra reached 96.7%, and the decontamination factor to thorium exceeded 105. The spectroscopic assessment suggested that the adsorbed species was mainly the positive Th4+ cation and almost no barium and nitrate ions were involved. The adsorption mechanism was dominated by compounding with oxygen in P-O-H and P=O groups. This work exhibited an excellent material and an efficient method for separating 228Ra and 224Ra from natural thorium, rendering it particularly significant in the future preparation and application of 212Pb.

Chemistry
Rapid and scalable preparation of highly quaternized polymer networks to achieve efficient simultaneous adsorption of iodide and pertechnetate

Meiyun Xu,Song Gu,Fulong Chen,Zhe Zhao,Peng Liu,Daoben Hua

DOI: https://doi.org/10.1007/s11426-024-2236-1

2024-10-19

Science China Chemistry

Abstract:The efficient separation of fission products, such as TcO 4 − and I − , holds strategic significance for the management of radioactive wastes and environmental protection. In this study, we propose an ultrafast strategy for scalable preparation of a highly quaternized organic network to facilitate efficient and synchronous separation of iodide and pertechnetate. The network can be prepared within a few minutes at room temperature, using polyethylenimine and 1,2,4,5-tetrakis(bromomethyl)benzene as building blocks. After chlorine replacement, the network, abundantly decorated with quaternary ammonium groups (Cl@QPN), exhibits an ultrahigh positive charge density of 7.6 mmol/g. This enables the rapid and efficient enrichment of target anions through strong electrostatic Coulomb interactions. As a result, Cl@QPN exhibits significantly higher adsorption rate constants of 0.830 g/(mg min) for ReO 4 − (a nonradioactive surrogate of TcO 4 − ) and 0.677 g/(mg min) for I − compared to other materials. Furthermore, it possesses high adsorption capacities, reaching 1,681 mg/g for ReO 4 − and 917.4 mg/g for I − . Cl@QPN also demonstrates good selectivity towards target ions and shows efficient adsorption for 99 TcO 4 − . Additionally, Cl@QPN exhibits high dynamic processing capacities, handling up to 3,100 and 7,400 kg of simulated streams per kilogram of material for I − and ReO 4 − , respectively.

chemistry, multidisciplinary
Optimised production of technetium-94m for PET imaging by proton-irradiation of phosphomolybdic acid in cyclotron liquid target

Ross Harper,Derek R. Morim,Dhyey Mehta,Veronika Rosecker,Stephen J. Archibald,Richard Southworth,Philip J. Blower,Karin A. Stephenson,Karin M. Nielsen

DOI: https://doi.org/10.1016/j.apradiso.2024.111381

IF: 1.787

2024-06-03

Applied Radiation and Isotopes

Abstract:Natural-abundance phosphomolybdic acid (H 3 (Mo 12 PO 40 ) ‧12H 2 O, 0.181-0.552 g Mo/mL) solutions were irradiated with 12.9 MeV protons on a GE PETtrace cyclotron using an adapted standard liquid target. Technetium-94m ( 94m Tc) was produced through the 94 Mo(p,n) 94m Tc nuclear reaction with saturation yields of up to 53 ± 6 MBq/μA. End of bombardment activities of 161 ± 17 MBq and 157 ± 7 MBq were achieved for the 0.552 g Mo/mL solution (10 μA for 30 minutes) and 0.181 g Mo/mL solution (15 μA for 60 minutes), respectively. No visible degradation of the niobium target body and foil were seen during the irradiations of up to 15 μA for 60 minutes. The produced 94m Tc was separated from the target phosphomolybdic acid solution with >98% recovery using an aqueous biphasic extraction resin. Compared to previous reported liquid target methods for 94m Tc production, the better production yield, in-target solution stability during irradiation and 94m Tc separation recovery of phosphomolybdic acid makes it a very promising target material for routine clinical 94m Tc production at medical facilities with liquid targets already installed for 18 F production.

nuclear science & technology,radiology, nuclear medicine & medical imaging,chemistry, inorganic & nuclear
High-efficiency 99Tc separation from contaminated liquid waste using some anion exchange resins

DEBASISH DAS

DOI: https://doi.org/10.26434/chemrxiv-2024-jg1wl

2024-03-15

Abstract:99Tc removal from contaminated aqueous solution was explored using some commercially available anion exchange resins with various specifications. Various combinations of physicochemical parameters like polymeric network, pore diameter, percent cross-linking, bead size etc. were selected to appraise their impact on 99Tc uptake. Fundamental extraction properties such as effect of solution pH, equilibration time, effect of temperature were determined for obtaining the optimum extraction condition. The resins were characterized using BET, SEM, EDS, XPS, TG, FTIR spectroscopy to decipher the structure-extraction correlation and extraction mechanism. In order to quantify the loading capacity (745 mg/g as maximum) and ascertain the reaction mechanism, non-radioactive surrogate of TcO4-, i.e, ReO4- have been used. ReO4- quantity in solution was measured using UV-Vis spectrophotometry with λmax at 204 nm. 4M HNO3 was found be an effective reagent towards desorption from the loaded resins. The capture performance was found to deteriorate with γ-radiation particularly at higher absorbed dose (500 kGy onwards). Competition studies with most common anions found in ground water as well as soil such as Cl-, NO3-, SO42-, CO32-, PO43- indicate that, even in presence of high concentration (1:10000 molar ratio) of these interfering anions, TcO4- can be selectively extracted by the resins confirming their effectiveness towards the decontamination of real ground water with respect to 99Tc.

Chemistry
99 TcO 4 – Separation through Selective Crystallization Assisted by Polydentate Benzene-Aminoguanidinium Ligands

Rongzhen Xie,Nannan Shen,Xijian Chen,Jie Li,Yaxing Wang,Chao Zhang,Chengliang Xiao,Zhifang Chai,Shuao Wang

DOI: https://doi.org/10.1021/acs.inorgchem.1c00187

IF: 4.6

2021-04-15

Inorganic Chemistry

Abstract:99Tc is one of the most abundant radiotoxic isotopes in used nuclear fuel with a high fission yield and a long half-life. Effective removal of pertechnetate (TcO4–) from an aqueous solution is important for nuclear waste separation and remediation. Herein, we report a series of facilely obtained benzene-linked guanidiniums that could precipitate TcO4– and its nonradioactive surrogate ReO4– from a high-concentration acidic solution through self-assembly crystallization. The resulting perrhenate and pertechnetate solids exhibit exceptionally low aqueous solubility. The benzene-linked guanidiniums hold one of the highest TcO4– removal capacities (1279 mg g–1) among previously reported materials and possess a removal percentage of 59% for ReO4– in the presence of Cl– over 50 times. The crystallization mechanism was clearly illustrated by the single-crystal structures and density functional theory calculations, indicating that TcO4– is captured through a charge-assisted hydrogen bonding interaction and stabilized by π–π stacking layers. In addition, the removal process is easily recycled and no toxic organic reagents are introduced. This work provides a green approach to preliminarily separate TcO4– from high-level nuclear wastes.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acs.inorgchem.1c00187?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acs.inorgchem.1c00187</a>.Detailed synthesis of PBGs and characterization of PBGs and PBGs-ReO4 (<a class="ext-link" href="/doi/suppl/10.1021/acs.inorgchem.1c00187/suppl_file/ic1c00187_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

chemistry, inorganic & nuclear
Sequestration of Pertechnetate Using Carboxymethyl Cellulose Stabilized FeS Nanoparticles: Effectiveness and Mechanisms

Haodong Ji,Yangmo Zhu,Wen Liu,Michael J. Bozack,Tianwei Qian,Dongye Zhao

DOI: https://doi.org/10.1016/j.colsurfa.2018.10.048

IF: 5.518

2019-01-01

Colloids and Surfaces A Physicochemical and Engineering Aspects

Abstract:Technetium (Tc-99) typically exists as pertechnetate (TcO4-) and hydrated oxide (TcO2 center dot nH(2)O) in soil and groundwater. While the former, Tc(VII), is very soluble and mobile in the environment, the latter is considered sparingly soluble and immobile. Consequently, immobilization of Tc(VII) can be achieved through conversion of Tc(VII) into Tc(IV). In this study, carboxymethyl cellulose (CMC) stabilized FeS nanoparticles (CMC-FeS) were prepared and tested for reductive immobilization of Tc(VII). Effects of nanoparticle dosage and water chemistry, including pH, humic acid and Ca2+ ions, were examined. At a dosage of 100 mg/L of CMC-FeS as Fe, CMC-FeS rapidly removed > 96% of 1.2 mu M of Tc(VII) within 1 h, with a retarded first-order rate constant (k(a)) of 150.32 h(-1). Higher pH in the range of 5.0-9.0 favored the reaction, with an optimal pH range of 8.0-9.0. While Ca2+ (up to 2 mM) only modestly affected the Tc(VII) removal, high concentrations of humic acid (up to 10 mg/L as TOC) showed increased inhibition on the Tc(VII) removal rate. FTIR and XPS analyses indicated that CMC-FeS immobilized TcO4- through reductive conversion of TcO4- into TcO2(s) and formation of Tc2S7 precipitate. The immobilized Tc remained insoluble when aged for 100 days under anoxic conditions, whereas up to 22.9% of the immobilized Tc was remobilized when it was exposed to air for 100 days.
Separation of Protactinium Employing Sulfur-Based Extraction Chromatographic Resins

Tara Mastren,Benjamin W Stein,T Gannon Parker,Valery Radchenko,Roy Copping,Allison Owens,Lance E Wyant,Mark Brugh,Stosh A Kozimor,F Meiring Nortier,Eva R Birnbaum,Kevin D John,Michael E Fassbender

DOI: https://doi.org/10.1021/acs.analchem.8b01380

2018-06-05

Abstract:Protactinium-230 ( t1/2 = 17.4 d) is the parent isotope of 230U ( t1/2 = 20.8 d), a radionuclide of interest for targeted alpha therapy (TAT). Column chromatographic methods have been developed to separate no-carrier-added 230Pa from proton irradiated thorium targets and accompanying fission products. Results reported within demonstrate the use of novel sulfur bearing chromatographic extraction resins for the selective separation of protactinium. The recovery yield of 230Pa was 93 ± 4% employing a R3P═S type commercially available resin and 88 ± 4% employing a DGTA (diglycothioamide) containing custom synthesized extraction chromatographic resin. The radiochemical purity of the recovered 230Pa was measured via high purity germanium γ-ray spectroscopy to be >99.5% with the remaining radioactive contaminant being 95Nb due to its similar chemistry to protactinium. Measured equilibrium distribution coefficients for protactinium, thorium, uranium, niobium, radium, and actinium on both the R3P═S type and the DGTA resin in hydrochloric acid media are reported, to the best of our knowledge, for the first time.
Separation of ReO 4 − /TcO 4 − from simulated radioactive waste liquid by a novel series of anion exchange resins

Yiwei Huang,Xinlong Chen,Yinglin Shen,Xiaomin Li,Xupeng Zhi,Peng Liu,Meiying Liu,Bin Liu

DOI: https://doi.org/10.1515/ract-2023-0261

2024-03-29

Radiochimica Acta

Abstract:Selective removal of 99 TcO4 − from radioactive wastewater is a challenging but significant task, which benefits spent fuel reprocessing and radioactive-waste leakage treatment. This work introduces the performance of adsorption ReO 4 − using a series of novel anion exchange resins, namely MAPE-1, MAPE-2, MAPE-3, and MAGD-1, impregnated with functionalized ionic liquids as active sites. They exhibit a high selectivity towards TcO4 − /ReO4 − , in a wide pH range of pH 5–11 for ReO4 − /TcO4 − adsorption. Among these resins, MAPE-1 has the best adsorption performance for ReO 4 − , with a maximum adsorption capacity of 202.4 mg/g and a high distribution ratio K d of 6.2 × 106 mL/g at pH 7. The adsorption mechanism involves anion exchange between functionalized ionic liquids and TcO4 − /ReO4 − , which is supported by X-ray energy dispersive spectroscopy (EDS) and Fourier Transform Infrared spectroscopy (FT-IR) analyses. In addition, X-ray photoelectron spectroscopy (XPS) further illustrates the interaction between the resin and perrhenate.

chemistry, inorganic & nuclear,nuclear science & technology

AGE AND DISEASE‐RELATED ALTERATIONS IN FIBRINOGEN‐EUGLOBULIN (FIBHINOLYTIC) BEHAVIOR

Synthesis of a Novel Silica‐Based Macroporous Polymer Containing TODGA Chelating Agent and Its Application in the Chromatographic Separation of Mo(VI) and Zr(IV) from Diethylenetriaminepentaacetic Acid

Properties and Mechanism of Molybdenum and Zirconium Adsorption by a Macroporous Silica‐Based Extraction Resin in the MAREC Process

Quantitative Assessment of Scanning Electron Microscope Defects in Uncombable‐Hair Syndrome

Production and separation of 99mTc from cyclotron irradiated 100/naturalMo targets: a new automated module for separation of 99mTc from molybdenum targets

Molecular Modification of a Novel Macroporous Silica-Based Impregnated Polymeric Composite by Tri-N-butyl Phosphate and Its Application in the Adsorption for Some Metals Contained in a Typical Simulated HLLW.

Bleeding evaluation of the stationary phase from a few novel macroporous silica-substrate polymeric materials used for radionuclide partitioning from HLLW in MAREC process

Adsorption and Chromatographic Separation of Mo(VI) and Zr(IV) Ions from a High-Concentration Oxalic Acid Solution by a Macroporous Silica-Based N,N,N′,N′-Tetraoctyl-3-Oxapentane-1,5-Diamide Polymeric Adsorbent

Simple separation of technetium from molybdenum for tracer isotope production

Nicorandil-induced severe oral ulceration.

Water extraction of technetium-99m from neutron irradiated porous molybdenum dioxide pellet

Extraction of pertechnetate and perrhenate from water with deep-cavity [CpFe(arene)](+)-derivatized cyclotriveratrylenes

Adsorption and separation of terbium(III) and gadolinium(III) from aqueous nitrate medium using solid extractant

Preparation and characterization of a mesoporous silica-based copolymer loaded with bis(2-ethylhexyl) phosphate for the efficient separation of trace radium from natural thorium

Rapid and scalable preparation of highly quaternized polymer networks to achieve efficient simultaneous adsorption of iodide and pertechnetate

Optimised production of technetium-94m for PET imaging by proton-irradiation of phosphomolybdic acid in cyclotron liquid target

High-efficiency 99Tc separation from contaminated liquid waste using some anion exchange resins

99 TcO 4 – Separation through Selective Crystallization Assisted by Polydentate Benzene-Aminoguanidinium Ligands

Sequestration of Pertechnetate Using Carboxymethyl Cellulose Stabilized FeS Nanoparticles: Effectiveness and Mechanisms

Separation of Protactinium Employing Sulfur-Based Extraction Chromatographic Resins

Separation of ReO 4 − /TcO 4 − from simulated radioactive waste liquid by a novel series of anion exchange resins