The significance of thoracolumbar spinal canal size in spinal cord injury patients.

P. Korovessis

DOI: https://doi.org/10.1097/00007632-200109150-00026

IF: 3.241

2001-09-15

Spine

Abstract:

What problem does this paper attempt to address?

A 180 Nm-Cmos Asymmetric UWB-RFID Tag with Real-time Remote-monitored ECG-sensing

Jue Shen,Jia Mao,Geng Yang,Li Xie,Yi Feng,Majid Baghaei Nejad,Zhuo Zou,Fredrik Jonsson,Hannu Tenhunen,Lirong Zheng

DOI: https://doi.org/10.5220/0005286302100215

2015-01-01

Abstract:This paper proposes an asymmetric ultra-wideband - radio frequency identification (UWB-RFID) tag with electrocardiogram (ECG)-sensing capability for patients remote-monitoring in hospital environment. A UWB-RFID communication protocol is suggested for real-time transmission of undistorted ECG by interleaving ADC sampling and burst-mode UWB transmission. The proposed system shows a maximum accessing capability of 400 tags/second at 1.5 KHz ECG sampling rate with 10 Mbps UWB pulse rate. The tag consists of UHF-RFID receiver, UWB transmitter, ECG analog front-end, multi-input ADC and baseband circuitry integrated on two silicon dies. It was implemented by 6 mm(2) -sized 180 nm CMOS technology. Electrodes for ECG-sensing are manufactured by inkjet-printing on polyimide substrate. Experiment results show that the tag transmits UWB pulses at 1 Mbps rate with 18 mu W power. The printed electrodes conduct ECG waveform comparable to commercial electrodes.
A Multi-Parameter Bio-Electric ASIC Sensor with Integrated 2-Wire Data Transmission Protocol for Wearable Healthcare System

Geng Yang,Jian Chen,Fredrik Jonsson,Hannu Tenhunen,Li-Rong Zheng

DOI: https://doi.org/10.1109/date.2012.6176512

2012-01-01

Abstract:This paper presents a fully integrated application specific integrated circuit (ASIC) sensor for the recording of multiple bio-electric signals. It consists of an analog front-end circuit with tunable bandwidth and programmable gain, a 6-input 8-bit successive approximation register analog to digital converter (SAR ADC), and a reconfigurable digital core. The ASIC is fabricated in a 0.18-μm 1P6M CMOS technology, occupies an area of 1.5 x 3.0 mm 2 , and totally consumes a current of 16.7 μA from a 1.2 V supply. Incorporated with the ASIC, an Intelligent Electrode can be dynamically configured for on-site measurement of different bio-signals. A 2-wire data transmission protocol is also integrated on chip. It enables the serial connection over a group of Intelligent Electrodes, thus minimizes the number of connecting cables. A wearable healthcare system is built upon a printed Active Cable and a scalable number of Intelligent Electrodes. The system allows synchronous processing of maximum 14-channel bio-signals. The ASIC performance has been successfully verified in in-vivo bio-electric recording experiments.
An ASIC Solution for Intelligent Electrodes and Active-Cable Used in a Wearable ECG Monitoring System.

Geng Yang,Jian Chen,Fredrik Jonsson,Hannu Tenhunen,Li-Rong Zheng

2009-01-01

Abstract:This paper describes a digital CMOS Application Specific Integrated Circuit (ASIC) solution with the complete data acquisition and transmission for the use in a wearable electrocardiography (ECG) monitoring system. The main particularity of this system is related to the proposed reconfigurable microchip architecture for an intelligent electrode. The chip area is 2.3 mm(2) in a standard 0.18 mu m CMOS technology. The chip is operating at 24 MHz system clock with 3.3 V power supply for I/O cells and 1.8 V for the core circuit respectively. The estimated dynamic power dissipation is only 857 mu W. The post-layout simulation results show that the microchip embedded inside an intelligent electrode features ultra low power consumption and is quite feasible for a hand-held Personal Health Assistant (PHA) which uses a battery as energy source.
An Active-Cable Connected ECG Monitoring System for Ubiquitous Healthcare

Geng Yang,Ying Cao,Jian Chen,Hannut Tenhunen,Li-Rong Zheng

DOI: https://doi.org/10.1109/iccit.2008.101

2008-01-01

Abstract:In this paper, novel microchip architecture for a "smart electronic electrode" has been proposed. Furthermore, a new concept for wearable electrocardiography (ECG) monitoring system especially designed for ubiquitous healthcare is described. The patient can wear single Active-Cable connected smart electronic electrodes with wireless transmission of ECG signals to a dedicated Personal Health Assistant (PHA). The system will act as a continuous ECG data and event recorder, which can be used to follow up patients who have survived cardiac arrest or ventricular tachycardia but also for diagnostic purposes for patients with chronic diseases. A microchip prototype for the smart electronic electrode is implemented using UMC 0.18 um process. The post-layout simulation results show that the smart electronic electrode with ultra low power consumption is quite feasible for a hand-held PHA which uses a battery as energy source.
Intelligent electrode design for long-term ECG monitoring at home: Prototype design using FPAA and FPGA

Geng Yang,Jian Chen,Hannu Tenhunen,Li-Rong Zheng

DOI: https://doi.org/10.4108/ICST.PERVASIVEHEALTH2009.6005

2009-01-01

Abstract:A personal medical device supporting continuous biosignals monitoring is presented. The novelty of this paper is to provide an intelligent electrode suitable for long-term ECG monitoring. The proposed intelligent electrode is composed of an ASIC chip and a micro pikes array established on a gauze plaster substrate. By comparing the signal quality, the patients comfort and convenience, the proposed intelligent electrode could be an alternative to the traditional adhesive electrode. A prototype for the intelligent electrode is built up based on programmable FPAA and FPGA chips.
Passive and Wireless Near Field Communication Tag Sensors for Biochemical Sensing with Smartphone

Gang Xu,Qian Zhang,Yanli Lu,Lei Liu,Daizong Ji,Shuang Li,Qingjun Liu

DOI: https://doi.org/10.1016/j.snb.2017.02.149

IF: 9.221

2017-01-01

Sensors and Actuators B Chemical

Abstract:Wireless, passive, low-cost and portable detection systems are in high demand for environment monitoring, food safety and health care diagnosis. Among them smartphone-based sensing systems are receiving special attention with the worldwide popularity of smartphones. Over the past decade, many devices, including a large number of smartphones in today's marketplace, are integrated with near field communication (NFC) modules. Leveraging the worldwide ubiquity of these devices, we developed wireless and passive NFC tag sensors based on flexible arid low-cost NFC tags for biochemical sensing. NFC-enabled smartphone was used to wirelessly power the sensors and receive the detection results through inductive coupling. By adopting rheostats in the resonant circuits of the sensors, we easily achieved accurate semi quantitative detection of different analytes constructed sensor arrays. The results demonstrated that the tag sensors could be used to discriminate gases at part-per-million concentrations and analytes in solution such as ions and bacteria in different concentration ranges. Thus, the wireless, passive, low-cost and flexible NFC tag sensors unfolded new dimensions for biochemical sensing with smartphones (C) 2017 Elsevier B.V. All rights reserved.
Design of a self-organized Intelligent Electrode for synchronous measurement of multiple bio-signals in a wearable healthcare monitoring system

Geng Yang,Jia Mao,Tenhunen, H.,Li-Rong Zheng

DOI: https://doi.org/10.1109/ISABEL.2010.5702786

2010-01-01

Abstract:This paper presents an Intelligent Electrodes and Active Cable based wearable medical system. Within each Intelligent Electrode, an Application Specific Integrated Circuit (ASIC) is integrated which includes a gain-bandwidth selectable analog front-end circuit, an 8-bit SAR ADC and a digital controller. The key of the ASIC is the analog front-end circuit with tunable gain and bandwidth which can be configured for Electrocardiogram (ECG), Electroencephalogram (EEG) or Electromyogram (EMG) measurement. Common mode interference is effectively rejected due to the circuit's high Common Mode Rejection Ratio (CMRR), which is higher than 135 dB up to 100 Hz and better than 110dB up to 1 kHz. Since a dedicated data transmission protocol is implemented on chip, the Intelligent Electrodes can establish a self-organized network and perform synchronous measurements for multiple bio-signals.
A System-on-chip and Paper-Based Inkjet Printed Electrodes for a Hybrid Wearable Bio-Sensing System

Li Xie,Geng Yang,Matti Mantysalo,Fredrik Jonsson,Li-Rong Zheng

DOI: https://doi.org/10.1109/embc.2012.6347122

2012-01-01

Abstract:This paper presents a hybrid wearable bio-sensing system, which combines traditional small-area low-power and high-performance System-on-Chip (SoC), flexible paper substrate and cost-effective Printed Electronics. Differential bio-signals are measured, digitized, stored and transmitted by the SoC. The total area of the chip is 1.5 × 3.0 mm2. This enables the miniaturization of the wearable system. The electrodes and interconnects are inkjet printed on paper substrate and the performance is verified in in-vivo tests. The quality of electrocardiogram signal sensed by printed electrodes is comparable with commercial electrodes, with noise level slightly increased. The paper-based inkjet printed system is flexible, light and thin, which makes the final system comfortable for end-users. The hybrid bio-sensing system offers a potential solution to the next generation wearable healthcare technology.
A Wireless Powered Implantable and Flexible Neural Recording and Stimulating System Based on NFC Protocol

Zishang He,Yizhou Jiang,Ikwan Kim,Han Jin,Chenjie Dong,Junshang Li,Zhuo Zou,Li-rong Zheng,Yajie Qin

DOI: https://doi.org/10.1109/cicta.2018.8706062

2018-01-01

Abstract:A wireless-powered implantable sensor tag for neural recording and brain stimulation (NRS) based on standard Near Field Communication (NFC) protocol is presented. A NRS system is thus established with this dedicated but flexible sensor tag and a Proximity Coupling Device (PCD), which can be replaced with an NFC smart phone. The flexible printed sensor tag consists of a customized NRS System on Chip (SoC) and a customized NFC Proximity Card (PICC) SoC. Neural signals are captured by the sensor tag and transmitted to the PCD wirelessly. The measured signal-to-noise-and-distortion-rate (SNDR) was 35 dB in vitro.
An Implantable RFID Sensor Tag Toward Continuous Glucose Monitoring

Zhibin Xiao,Xi Tan,Xianliang Chen,Sizheng Chen,Zijian Zhang,Hualei Zhang,Junyu Wang,Yue Huang,Peng Zhang,Lirong Zheng,Hao Min

DOI: https://doi.org/10.1109/jbhi.2015.2415836

IF: 7.7

2015-01-01

IEEE Journal of Biomedical and Health Informatics

Abstract:This paper presents a wirelessly powered implantable electrochemical sensor tag for continuous blood glucose monitoring. The system is remotely powered by a 13.56-MHz inductive link and utilizes an ISO 15693 radio frequency identification (RFID) standard for communication. This paper provides reliable and accurate measurement for changing glucose level. The sensor tag employs a long-term glucose sensor, a winding ferrite antenna, an RFID front-end, a potentiostat, a 10-bit sigma-delta analog to digital converter, an on-chip temperature sensor, and a digital baseband for protocol processing and control. A high-frequency external reader is used to power, command, and configure the sensor tag. The only off-chip support circuitry required is a tuned antenna and a glucose microsensor. The integrated chip fabricated in SMIC 0.13-μm CMOS process occupies an area of 1.2 mm × 2 mm and consumes 50 μW. The power sensitivity of the whole system is -4 dBm. The sensor tag achieves a measured glucose range of 0-30 mM with a sensitivity of 0.75 nA/mM.
Wireless powered implantable bio-sensor tag system-on-chip for continuous glucose monitoring

Shuo Guan,Jingren Gu,Zhonghan Shen,Junyu Wang,Yue Huang,Andrew Mason

DOI: https://doi.org/10.1109/BioCAS.2011.6107760

2011-01-01

Abstract:An implantable passive radio frequency identification (RFID) sensor tag system-on-chip (SoC) for glucose monitoring is developed in this paper. A high frequency RFID tag, a bio-sensor interface, as well as the electrodes are included in this chip. The signal of blood sugar level from the bio-sensor is detected and converted into digital data, and then the data is encrypted and transmitted to an RFID reader on top of the skin. To measure the weak current signals, a current readout circuit, a current splitter, an ADC and a potentiostat are designed in the chip. Correlated double sample (CDS) technology is used in the readout circuit to reduce the 1/f noise and the op-amp's offset. The chip is taped out in SMIC 0.13 μm CMOS process. Simulation results show that the system can measure weak current signals in the range of 10 fA-100 pA.
Fully Wireless, In Vivo Assessment of Superimposed Physiological Vital Signs Using a Biodegradable Passive Tag Interrogated with a Wearable Reader Patch

Gyan Raj Koirala,Dong‐Hyun Lee,Young Jin Jo,Yeong Hwan Kim,Joo Hwan Shin,Jiyu Hyun,Yong Ming,Chanho Jeong,Suk Ho Bhang,Tae‐il Kim

DOI: https://doi.org/10.1002/adfm.202413363

IF: 19

2024-11-08

Advanced Functional Materials

Abstract:This study presents a fully wireless in vivo signal acquisition system featuring a biodegradable passive tag incorporating a tunable gelatin‐ionic liquid substrate and a nanoscale crack‐based strain gauge sensor, along with a wearable reader patch for interrogating with the implanted passive tag and transmitting sensor response to peripheral devices. The proposed system demonstrates real‐time efficacy in recording and processing superimposed vital signs. State‐of‐the‐art biosignal monitoring systems strive to achieve a balance between biocompatibility, biodegradability, and miniaturized, unobtrusive signal acquisition, thus requiring further research for improved user safety, mobility, and comfort. Here, a fully wireless sensing system is presented for real‐time in vivo assessment of physiological vital signs, addressing these challenges to enhance performance and user experience. The system features a biodegradable passive tag with a nanoscale crack‐based strain gauge sensor connected to a coil antenna on a gelatin‐ionic liquid substrate (GIS). The thermal crosslinking in the GIS promotes adhesion, while the presence of ionic liquid decreases the self‐resonance frequency of the BCA to below 100 MHz, enabling the device to operate in detuned mode. A lightweight (1.547 g) wearable reader patch interrogates an implanted passive tag via near‐field inductive coupling and transmits sensory data to peripheral devices via Bluetooth. Thus, the system ensures minimal tissue absorption and extended transmission range while consuming ≈80 mW of power during operation. In vitro and in vivo studies, culminating in successful implementation within a rat model, validated the implanted tag's biocompatibility and the system's capability to wirelessly acquire and process superimposed physiological vital signs, highlighting its potential to enhance patient outcomes through improved diagnostic and monitoring practices.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Hardware Design of NFC Authentication Device Used in Shared EV

Fugen Zhu,Shusheng Xiong,Wei Li,Cailing Zhou

DOI: https://doi.org/10.19620/j.cnki.1000-3703.20172098

2018-01-01

Abstract:In order to provide a man-machine interface for customers to get and return vehicle in the unattended business model of shared EV, a complete schematic circuits was designed based on the STM8AF52 MCU, PN512 NFC IC. After the PCB sample was made, the capacitance, inductance and resistance in the antenna matching circuit were adjusted to appropriate value, and reliability test of CAN communication was carried out. The results show that the NFC communication antenna operates normally at the distance less than 7 cm. The power consumption under standby mode is less than 5 mA. There are no CAN communications errors during 1 200 hours test, and display brightness can meet the requirement of man-machine interaction.
Digital Control Processor Design in an Implantable Bio-Sensor RFID Tag

刘力睿,闫潇,王俊宇

DOI: https://doi.org/10.15943/j.cnki.fdxb-jns.2012.06.007

2012-01-01

Abstract:A low-voltage,low-power digital control processor for implantable biosensor RFID tags is presented.It is compatible with the 'ISO/IEC 15693: 2000,IDT',and hummingbird cryptographic algorithm.It also meets the special requirement of control logic for weak current detection.Simulation results show that the system can measure weak current signals in the range of 10fA—100pA.
A Novel Secure NFC-based Approach for BMS Monitoring and Diagnostic Readout

Fikret Basic,Claudia Rosina Laube,Christian Steger,Robert Kofler

DOI: https://doi.org/10.1109/RFID54732.2022.9795979

2023-11-21

Abstract:In modern systems that rely on the use of Battery Management Systems (BMS), longevity and the re-use of battery packs have always been important topics of discussion. These battery packs would be stored inside warehouses where they would need to be properly monitored and configured before their re-integration into the new systems. Traditional use of wired connections can be very cumbersome, and sometimes even impossible, due to the outer layers and packaging. To circumvent these issues, we propose an extension to the conventional BMS design that incorporates the use of Near Field Communication (NFC) for the purpose of wireless battery pack status readout. Additionally, to ensure that these packs are only managed by authenticated devices and that the data that is communicated with is protected against outside eavesdropping and tampering, we present a solution in the form of a lightweight security layer on top of the NFC protocol. To show the feasibility of our design, an accompanying prototype has been implemented and evaluated.

Cryptography and Security,Hardware Architecture,Systems and Control
Power Transferring and Analogue Communication Approach for Implantable Devices.

Jun Ma,Jun Du,Jingjing Wang,Chunxiao Jiang,Yong Ren,Mohsen Guizani,M. Shamim Hossain

DOI: https://doi.org/10.1109/infcomw.2019.8845078

2019-01-01

Abstract:In this paper, we introduce a new approach of power transferring and communication for implantable devices to retrieve information from an implanted sensor. This approach originates in Radio Frequency Identification (RFID), and uses an analogue approach to communicate in order to decrease the complexity of implanted part and influence of attenuation, which requires coupling of coils. The design of power transferring mechanism consists of two parts, i.e., one reader and one label, which are similar to but actually different from those of RFID. To be specific, RFID uses electromagnetic fields to automatically identify and track the label attached to the object. In this work, the label can be implanted into a human body, and the reader is used to retrieve information from the label. The label is passive and the reader is active. When the reader transmits interrogator signals to the label, it will feedback the reader with two voltages, i.e., one is obtained with sensor and one without. The voltages are then used to locate the corresponding resistance of the sensor in a table. Experiment results of this work show that it is possible to retrieve information from a sensor placed on a passive label using load modulation approach in analogue manner. In addition, by computing the attenuation of human tissues to electromagnetic waves of different frequencies, we draw the conclusion that low frequencies are adaptive for the environment of human body.
ASIC Implementation of Low Power Baseband Processor for UHF RFID Tag

Qiuling Zhu,Chun Zhang,Xiaohui Wang,Zhongqi Liu,Yongming Li,Zhihua Wang

DOI: https://doi.org/10.3969/j.issn.1003-353X.2009.02.018

2009-01-01

Abstract:A novel digital baseband processor of an UHF BFID tag Wag presented based on the ISO/IEC 18000-6 type C standard.In order to enhance the sisnal-noise ratio in the return link.spread spectrum technique was used in addition to the FMO encoding/Miller sub-carrier modulation.The tag supports all the 11 mandatory commands required by the 6C standard as well as the implementation of pmbabilistic/slotted anticollision scheme and read/write operation to EEPROM.Low power techniques were adopted to reduce the instantaneous power and average power.The chip Wag designed and fabricated using 0.18μm 6 metal layers CMOS technology.From the measurement result.tlle overall power consumption is about 16 μW at the minimum voltage of 1.04 V,and the chip area is of 0.5 mm2.
Multimodal Wireless-Powered Flexible System for Closed-Loop Neuromodulation

Han Jin,Yizhou Jiang,Jianzheng Li,Shouyan Wang,Yajie Qin

DOI: https://doi.org/10.1109/JSEN.2023.3284067

IF: 4.3

2023-01-01

IEEE Sensors Journal

Abstract:This article presents a wirelessly powered closed-loop neuromodulation system, containing both implantable and wearable parts. The implantable part is an implantable neuromodulator tag that contains a customized application specific integrated circuit (ASIC) for neurostimulation and recording, an off-the-shelf near-field communication (NFC) proximity integrated circuit card (PICC) chip, and one coupling coil for communication and power transferring. There is a wireless monitoring device, an NFC reader, electroencephalogram (EEG) electrodes, and near-infrared spectrum (NIRS) modules in wearable part. Intracranial neural recorder and wearable EEG/NIRS modules are able to provide multimodal biological information, such as local field potentials (LFPs), EEG, and cerebral tissue oxygen saturation (StO(2)) for algorithms to propose a more precise closed-loop stimulation strategy for better treatment effect. The ASIC chip is fabricated in a 0.18-mu m CMOS technology. The stimulator has a limited size of 0.027 mm(2). Its stimulation current ranges from 0 to 0.6 mA with a bandwidth of 10 Hz-8 kHz, which is able to support precise neuromodulation. The recording channel features a bandwidth of 0.5-100 Hz with a noise floor of 0.93 mu V-rms. The entire neuromodulator tag has a small footprint of 20 x 24 x 1.4 mm, and its weight is only 0.25 g.
A flexible ECG patch compatible with NFC RF communication

Mohammad Zulqarnain,Stefano Stanzione,Ganesh Rathinavel,Steve Smout,Myriam Willegems,Kris Myny,Eugenio Cantatore

DOI: https://doi.org/10.1038/s41528-020-0077-x

IF: 14.6

2020-07-15

npj Flexible Electronics

Abstract:Abstract With the advent of the internet of things, flexible wearable devices are gaining significant research interest, as they are unobtrusive, comfortable to wear and can support continuous observation of physiological signals, helping to monitor wellness or diagnose diseases. Amorphous Indium Gallium Zinc Oxide (a-IGZO) Thin Film Transistors (TFTs) fabricated on flexible substrates are an attractive option to build such bio-signal monitoring systems due to their flexibility, conformability to the human body, and low cost. This paper presents a flexible electrocardiogram (ECG) patch implemented on foil with self-aligned IGZO TFTs, which is capable to acquire the ECG signals, amplify them and convert them to a sequence of bits. The analogue frontend has a measured input-referred noise of 8 μV rms in the 1–100 Hz band. The system achieves experimentally 67.4 dB CMRR, 58.9 dB PSRR, and 16.5 MΩ input impedance at 50 Hz while using 1 kHz chopping. The signal from the electrodes is transformed to a 105.9-kb/s Manchester-encoded serial bit stream which could be sent wirelessly to a smart phone via Near Field Communication (NFC) for further elaboration. Power consumption is 15.4 mW for the digital and 280 μW for the analogue part. This contribution shows the fundamental steps to demonstrate intelligent plasters for biomedical applications based on flexible electronics providing an NFC-compatible digital output bit stream.

materials science, multidisciplinary,engineering, electrical & electronic
NFC-Enabled Dual-Channel Flexible Printed Sensor Tag

Jonghyun Choi,Ian Visagie,Yi Chen,Robert Abbel,Kate Parker

DOI: https://doi.org/10.3390/s23156765

2023-07-28

Abstract:Wireless sensor tags in flexible formats have numerous applications; some are commercially available for specific target applications. However, most of these wireless sensor tags have been used for single-sensing applications. In this study, we designed a printed circuit board (PCB) module (13 mm × 13 mm) for near-field communication-enabled sensor tags with both electrical resistance and capacitance read-out channels that enables dual-channel sensing. As part of the wireless sensor tag, a square antenna pattern was printed directly on a flexible poly(ethylene terephthalate) (PET) substrate and integrated into the PCB module to demonstrate a dual-channel temperature and ethylene gas sensor. The temperature and ethylene sensors were printed using a positive temperature coefficient ink and a tin oxide (SnO2) nanoparticle ink, respectively. With dual sensing capabilities, this type of sensor tag can be used in smart packaging for the quality monitoring of fresh produce (e.g., bananas) by tracking temperature and ethylene concentration in the storage/transport environment.

The significance of thoracolumbar spinal canal size in spinal cord injury patients.

A 180 Nm-Cmos Asymmetric UWB-RFID Tag with Real-time Remote-monitored ECG-sensing

A Multi-Parameter Bio-Electric ASIC Sensor with Integrated 2-Wire Data Transmission Protocol for Wearable Healthcare System

An ASIC Solution for Intelligent Electrodes and Active-Cable Used in a Wearable ECG Monitoring System.

An Active-Cable Connected ECG Monitoring System for Ubiquitous Healthcare

Intelligent electrode design for long-term ECG monitoring at home: Prototype design using FPAA and FPGA

Passive and Wireless Near Field Communication Tag Sensors for Biochemical Sensing with Smartphone

Design of a self-organized Intelligent Electrode for synchronous measurement of multiple bio-signals in a wearable healthcare monitoring system

A System-on-chip and Paper-Based Inkjet Printed Electrodes for a Hybrid Wearable Bio-Sensing System

A Wireless Powered Implantable and Flexible Neural Recording and Stimulating System Based on NFC Protocol

An Implantable RFID Sensor Tag Toward Continuous Glucose Monitoring

Wireless powered implantable bio-sensor tag system-on-chip for continuous glucose monitoring

Fully Wireless, In Vivo Assessment of Superimposed Physiological Vital Signs Using a Biodegradable Passive Tag Interrogated with a Wearable Reader Patch

Hardware Design of NFC Authentication Device Used in Shared EV

Digital Control Processor Design in an Implantable Bio-Sensor RFID Tag

A Novel Secure NFC-based Approach for BMS Monitoring and Diagnostic Readout

Power Transferring and Analogue Communication Approach for Implantable Devices.

ASIC Implementation of Low Power Baseband Processor for UHF RFID Tag

Multimodal Wireless-Powered Flexible System for Closed-Loop Neuromodulation

A flexible ECG patch compatible with NFC RF communication

NFC-Enabled Dual-Channel Flexible Printed Sensor Tag