Abstract:Electrothermal materials have been widely used due to controllable heat energy in our life. With the development of wearable technology, a flexible, safe and waterproof heater with the good ability to endure repeated bending is required in future. In this paper, we have developed a novel wearable heater based on flexible, stretchable graphite nanoplates and polyurethane (GNP/PU) nanocomposite films. Firstly, the GNP/PU thin films with a thickness of 30-200 mu m were fabricated in mass production by the method of gap-coating, which can be bent 180 degrees repeatedly, or even knotted for their excellent flexibility, and has a maximum elongation up to 387.8%, due to the homogenous distribution of GNP in PU matrix. By the control on the amount of GNP and the thickness of the film, the minimum resistivity and square resistance of the GNP/PU films can be 80 m Omega.cm and 4 Omega/square, respectively. Through a further flexible structure designing and waterproof electronic packaging process, the fabricated wearable heaters are able to withstand 100,000 180-degrees bending with the resistance changes of only 3.24%, and have a IPX7 waterproof ability to work continuously for 120 min under 1.30 m water. Interestingly, as-prepared bare GNP/PU films have a good resistence to water and salt erosion, with the light 2.1%, 2.4% and 3.1% increasing in electrical resistance, and without obvious change in heating performance, even after the immersion in pure water, 0.5% and 5% salt water and dried completely. Furthermore, the wearable heaters can generate heat uniformly under the safe voltage of 5-24 V to achieve rapid heating and cooling rate of 25 degrees C/min and 13 degrees C/min, respectively. Lastly, a heating full-body vest mode of as-prepared wearable heaters was fabricated, which can work well with hand raising, bending and walking. The results showed that as-prepared wearable heaters were very suitable for wearable electronics, due to the excellent flexibility and stretchability of GNP/PU films and their special packaging structure, which provides a new choice for wearable heating products.

Positive temperature coefficient material based on silicone rubber/ paraffin/ graphite/ carbon nanotubes for wearable thermal management devices

Fabrication and performance evaluation of the flexible positive temperature coefficient material for self‐regulating thermal control

A Novel Flexible Room Temperature Positive Temperature Coefficient Material for Thermal Management

A New Thermal Controlling Material with Positive Temperature Coefficient for Body Warming: Preparation and Characterization

Theoretical and Experimental Studies on Thermal Control by Using a Novel PTC Material with Room Temperature Curie Point

High-precision Adaptive Temperature Control Performance of Thin Positive Temperature Coefficient Materials with Ultra-High Resistance-Temperature Coefficient

Polymer Positive Temperature Coefficient Composites with Room-Temperature Curie Point and Superior Flexibility for Self-Regulating Heating Devices

Studies on preparation and adaptive thermal control performance of novel PTC (positive temperature coefficient) materials with controllable Curie temperatures

Study on the low Curie point positive temperature coefficient (PTC) material based on the conductive model

Study on Dynamic Thermal Control Performance of Positive Temperature Coefficient (PTC) Material Based on a Novel Heat Transfer Model Considering Internal Heat Transfer

High temperature co-polyester thermoplastic elastomer nanocomposites for flexible self-regulating heating devices

Highly conductive and stretchable carbon nanotube/thermoplastic polyurethane composite for wearable heater

Properties of Surface Heating Textile for Functional Warm Clothing Based on a Composite Heating Element with a Positive Temperature Coefficient

Study on the Influence of Thermal Properties of Paraffin on Flexible PTC Materials

Development and Application of the Low Curie Point Positive Temperature Coefficient (PTC) Electrothermal Anti-Icing Material

Flexibility and shape memory of phase change material capable of rapid electric heating function for wearable thermotherapy

Flexible Highly Thermally Conductive PCM Film Prepared by Centrifugal Electrospinning for Wearable Thermal Management

Conformal Structured Ceramic Textiles with Passive and Active Heating Functionality

Flexible Positive Temperature Coefficient Composites (PVAc/EVA/GP-CNF) with Room Temperature Curie Point

Flexible, Stretchable, Waterproof (IPX7) Electro-thermal Films Based on Graphite Nanoplatelets & Polyurethane Nanocomposites for Wearable Heaters

A New Kind of Shape-Stabilized PCMs with Positive Temperature Coefficient (PTC) Effect