Abstract:Statement of problem: New production methods have been developed for metal-ceramic restorations. Different production methods may show different surface roughness and fit, which may affect retention and long-term success. Purpose: The purpose of this in vitro study was to examine 3 different production methods with regard to surface roughness, marginal and internal fit, and retention of cobalt-chromium alloy single-crown copings. Material and methods: A master abutment of a premolar mandibular tooth preparation with 4-mm height and a 0.6-mm deep 120-degree chamfer finish line with a 12-degree angle of convergence was replicated in die stone and scanned. Thirty-six cobalt-chromium alloy copings were produced using 3 different production techniques. Twelve copings were produced by laser-sintering, 12 by milling, and 12 by milled wax/lost wax. The surface microstructure of 2 copings in each group was analyzed using interferometry. The remaining 10 copings in each group were used to evaluate marginal and internal fit by using an impression material replica method, and retention was evaluated by using a uniaxial tensile force pull-off test. The copings from each test group were cemented with zinc phosphate cement onto resin abutments. Statistical analyses of differences in marginal and internal fit were performed using 1-way ANOVA and the Mann-Whitney U test. Differences in surface topography were analyzed with the Kruskal-Wallis and Mann-Whitney U tests for nonparametric data. Differences in retentive values were analyzed using the Mann-Whitney U test for nonparametric data (all α=.05). Results: Differences in surface microstructure were seen. The laser-sintered copings showed increased surface roughness compared with milled and milled wax/lost wax copings. Differences in marginal and internal fit were noted. Laser-sintered showed significantly smaller spaces between coping and abutment than milled wax/lost wax copings (P=.003). At the margins, laser-sintered copings showed significantly smaller spaces than either the milled wax/lost wax group (P=.002) or the milled group (P=.002). At the chamfer, laser-sintered copings showed significantly smaller spaces than milled wax/lost wax copings (P=.005). At the center of the axial walls, laser-sintered copings showed significantly smaller spaces than those in the milled wax/lost wax (P=.004) and milled copings (P=.005). No significant differences were noted between milled and milled wax/lost wax copings (P>.05). No significant differences were detected regarding retentive forces in the pull-off tests (P>.05). Conclusions: Laser-sintered Co-Cr crown copings showed increased surface roughness and better internal and marginal fit than copings produced by milling or milled wax/lost wax technique. However, the crown pull-off tests did not reveal any significant differences.

Tensile strength of Ni-Cr copings subjected to inner surface sandblasting using different cementing agents: An in vitro study

Adhesive bonding of resin composite to various Ni-Cr alloy surfaces using different metal conditioners and a surface modification system

Evaluation of the Effect of Different Surface Treatments on Luting CAD/CAM Composite Resin Overlay Workpieces

Improving the bonding stability between resin cements and zirconia-based ceramic using different surface treatments

Bond strength of three luting agents to zirconia ceramic - influence of surface treatment and thermocycling

Recycling CAD/CAM Lithium Disilicate Ceramic: Effect of Surface Treatment and Aging on the Bond Strength to Resin Cement

Effect of production method on surface roughness, marginal and internal fit, and retention of cobalt-chromium single crowns

Effect of sandblasting on the shear bond strength and durability of three resin cements bonded to titanium

Effectiveness of different surface treatments on bond strength between 3D‐printed teeth and denture base

The effect of different surface treatments on the shear bond strength of luting cements to titanium

Influence of Different Surface Treatments on the Bond Strength of Yttria-Stabilized Tetragonal Zirconia Ceramic

[Effect of different sandblasting conditions on the metal-ceramic bonding strength of Co-Cr alloy fabricated by selective laser melting technology]

Impact of altering the dispensing methods of resin-based cements on their physical and bonding qualities

Comparison of Retention and Seating of Implant-Supported Hard and Soft Metal Copings

Influence of surface treatment on repair bond strength of CAD/CAM long-term provisional restorative materials: an in vitro study

The effect of repeated surface treatment of zirconia on its bond strength to resin cement

Bond strength of resin cement to zirconia treated in pre-sintered stage

Investigating the impact of surface treatments on tensile bond strength between pediatric prefabricated zirconia crowns and primary maxillary incisors with various types of luting cement: an in vitro study

Influence of surface treatment of yttrium-stabilized tetragonal zirconium oxides and cement type on crown retention after artificial aging

The Influence of Contamination and Different Cleaning Methods and the Effect of Plasma Treatment of CoCr Alloy on Tensile Bond Strength to Composite Resin

Effect of different surface treatments and adhesive cementation on the surface topography and flexural strength of translucent and ultra‐translucent monolithic zirconia