Abstract:This study primarily aims to investigate the flow distribution and heat transfer characteristics of submerged jet cooling for the avionics server module. A comparison of flow and heat transfer performance between different submerged jet arrays with variable hole diameter ( D ) and hole pitch ( S ) is carried out by using three-dimensional numerical simulation. The results of temperature and streamline distribution show that the flow structure in the avionics server model can be subdivided into flow convection region, jet impingement region, and cross-flow region. Due to the drift phenomenon caused by horizontal crossflow being more obvious, the cross-flow region was very large for ( D = 2, S = 4), but the jet impingement region was observably smaller than that of ( D = 4, S = 16) and ( D = 5, S = 25). Parameter studies show that the average heat transfer performance at ( D = 4, S = 20) is observably better with average temperature was 46.5 °C and average Nusselt number was 13.25. The highest local heat transfer rate was found at ( D = 5, S = 10) with the minimum of maximum temperature and maximum local Nusselt number were 71.5 °C and 181.09, respectively. The analysis of partial first-order derivative of the pressure drop ( ΔP(S,D) ) and thermal resistance ( Rtot(S,D) ) shows that the pressure drop was less sensitive to variations in any D and S showed a positive effect on the heat transfer performance. Multi-objective optimization of the submerged jet array is further studied based on the response surface method with the ΔP and Rtot as the objectives. Additionally, the Non-dominated Sorting Genetic Algorithm II and Technique for Order Preference by Similarity to Ideal Solution were used to improve the accuracy of Pareto solutions. These Pareto solutions demonstrate that parameters D and S exhibit a clean function relationship, and the flow and heat transfer performance of the avionics server module was best matched with pressure drop was 6.05 kPa and thermal resistance was 0.145 °C/W at ( D = 5, S = 10).

Experimental and numerical study on the heat transfer performance inside integrated sublimator driven coldplate for aerospace applications

Numerical Investigate on the Heat Transfer Performance and Mechanical Analysis of a Water Sublimator{fr}Étude numérique et analyse mécanique des propriétés de transfert de chaleur des sublimateurs d'eau

Numerical Analysis of Heat Transfer Behaviours of Melting Process for Ice Thermal Storage Based on Various Heat Source Configurations

Experimental and numerical study of structural parameters on the heat transfer performance of submerged cooling system

Simulation of evaporation and sublimation process in porous plate water sublimator based on a reduced CFD model

Experimental Study on an Thermosyphon Loop with Bubble Pump Effect

Numerical study on heat transfer enhancement by spray-sublimation cooling with dry ice particles

Effect of Direct Liquid Cooling Technology With Flow Guide Integration on Avionics Devices Thermal and Electrical Performance

Experimental and Numerical Investigation on Heat Transfer Performance of Water Evaporators with Different Channels and Fin Structures in a Sub-Atmosphere Environment

A numerical study on multi-nozzle spray cooling of downward-facing heater surface

Numerical and experimental investigation of a novel liquid upper-feeding micro-channel flat loop thermosyphon cooling and heat recovery system

Study on the flow boiling characteristics of novel pin fin heat sinks in a two-phase mechanically pumped cooling loop

Experimental Study of Heat Transfer Characteristics of Pulsed Dry Ice Sublimation Spray Cooling with High Thermal Load

Numerical Study on the Cooling Method of Phase Change Heat Exchange Unit with Layered Porous Media

A review of water sublimation cooling and water evaporation cooling in complex space environments

Experimental Investigation into the Effect of Fin Shapes on Heat Dissipation Performance of Phase Change Heat Sink

Experimental Analysis of an Internally-Cooled Liquid Desiccant Dehumidifier

NUMERICAL SIMULATION AND ANALYSIS ON THE WORKING PROCESS OF WATER SUBLIMATOR

Performance analysis and design optimization of avionics devices with single-phase submerged jet cooling

Experimental investigation of a new hybrid structured surface for subcooled flow boiling heat transfer enhancement

Experimental Study of a Novel Heat Sink for Distribution Level Static Synchronous Compensator Cooling