Abstract:Inorganic CsPbIBr2 perovskite has been considered as a promising light-absorbing material for solar cells due to its high stability and suitable bandgap. Although the remarkable improvement of CsPbIBr2 PSC has been achieved, the efficiency of this cell is still lower than those of other analogues and far below its theoretical limit. This is mainly due to the serious charge recombination in the as-fabricated CsPbIBr2 cells derived from the poor-quality CsPbIBr2 perovskite film with a large quantity of defects and numerous grain boundaries. Therefore, fabricating high-quality CsPbIBr2 perovskite film is a key factor for the further efficiency improvement of CsPbIBr2 PSCs. Herein, phenylthiourea (PTU) additive is introduced into the CsPbIBr2 precursor to tailor the crystallization of CsPbIBr2 perovskite for fabricating high-quality CsPbIBr2 perovskite. The C=S group of PTU can coordinate with PbBr2 in the precursor owing to the lone-pair electrons on S and the empty orbits of Pb2+. The strong interaction between PTU and the CsPbIBr2 precursor components can form PTU·Pb···Br(I) intermediate phase in the precursor upon PTU introduction. The PTU·Pb···Br(I) intermediate phase can reduce the nucleation rate of perovskite and modulate the perovskite crystal growth because the extra energy is required to break the strong coordination bond in the intermediate phase, resulting in a low crystallization rate of CsPbIBr2 perovskite. Such a retardation of perovskite crystallization is conducive to the formation of high-crystallinity perovskite film with smooth surface, large crystal grains, high crystallization, and low density of defect. Meanwhile, the decomposition of PTU during thermal annealing makes the S2– inserted into interstitial of CsPbIBr2 crystal lattice, which greatly enhance the stability of CsPbIBr2 perovskite. The carbon-based PSCs with a normal n-i-p structure of FTO/compact-TiO2 layer/meso-TiO2 layer/perovskite film/carbon layer are fabricated, and their photovoltaic performances are measured under a simulated AM1.5 illumination (100 mW·cm–2). The PSC based on PTU-CsPbIBr2 perovskite delivers a high power conversion efficiency of 10.09%, which is much higher than that of the control device. This great improvement of photovoltaic performance can be attributed to the largely promoted perovskite quality, which enhances the charge collection and suppresses the charge recombination in the device. In addition, the unencapsulated device preserves 82% of the initial efficiency after being stored under ambient condition for 35 days, suggesting excellent stability. Therefore, this work provides an effective complementary strategy for effectively improving the performance of inorganic PSCs.

Encapsulation of CsPb2Br5 in TiO2 Microcrystals to Enhance Environmental Stability

Facile Synthesis of Environmentally Stable Cspb2br5/Tio2 Core/Shell Nanocrystals with Photoelectrochemically Active

Photoelectrochemically Active and Environmentally Stable CsPbBr3/TiO(2)Core/Shell Nanocrystals

Synthesis of CsPbX3 lead halide perovskite nanocrystals in flower-like TiO2 matrices with enhanced stability

Synthesis of Asymmetrical CsPbBr3/TiO2 Nanocrystals with Enhanced Stability and Photocatalytic Properties

Ultrastable CsPbBr3@CsPb2Br5@TiO2 Composites for Photocatalytic and White Light-Emitting Diodes

Readily Available Stable Non‐quantum dot CsPbBr3/TiO2 Heterostructure Crystals for Efficient photocatalyst

Well‐Dispersed CsPbBr3@TiO2 Heterostructure Nanocrystals from Asymmetric to Symmetric

Perovskite Nanocrystals in Situ Encapsulated in TiO2 Microspheres for Stable CO2 Photoreduction in Water.

Highly stable halide perovskites for photocatalysis via multi-dimensional structure design and in situ phase transition

In Situ Compositing CsPbBr3 with Exfoliated Layered-Perovskite CsCa2Ta3O10: Interfacial Interaction and Enhanced Stability

Exceptional Stability Against Water, UV Light, and Heat for CsPbBr3@Pb-MOF Composites

Improving the Stability of CsPbBr3 Perovskite Nanocrystals by Peroxides Post-treatment

In Situ Growth of CsPbBr 3 Perovskite Nanocrystals in Lead‐Based Matrix Toward Significantly Enhanced Water/Photo Stabilities

Continuous-flow synthesis of CsPbI3/TiO2 nanocomposites with enhanced water and thermal stability

Ultrastable Perovskite through a SiO 2 and PbSO 4 Double Protection Strategy

Photocatalytic Deposition of Nanostructured CsPbBr3 Perovskite Quantum Dot Films on Mesoporous TiO2 and Their Enhanced Visible-Light Photodegradation Properties

Ultra-Stable CsPbX3@Pyrophosphate Nanoparticles in Water over One Year

Ultrastable CsPbBr 3 @CsPb 2 Br 5 @TiO 2 Composites for Photocatalytic and White Light-Emitting Diodes

Tailoring of CsPbIBr2 Perovskite Crystallization Via Phenylthiourea for Stable and Efficiency Perovskite Solar Cells

Enhanced Stability of CsPbBr3 Nanocrystals through Al2O3 and Polymer Coating