Abstract:CFRP (Carbon Fiber Reinforced Polymer) is widely used in the aerospace, automobile and construction industries. Its non-homogeneous and anisotropic nature often results in unfavorable hole quality during the drilling process, and exit delamination is a resulting phenomenon that has received much attention. Exit delamination occurs when the drilling thrust force exceeds the critical thrust force. It adversely affects product quality and may even result in rejection. The thrust force on the chisel edge is an important component of the total thrust force, and it helps to predict the total thrust force so that delamination can be reduced or avoided. In this study, noticing that the chisel edge has a certain length, the author puts forward the novel concept of the azimuth angle on the basis of the micro analysis of the contact state between the chisel edge and the carbon fiber. In addition to the orientation angle of the carbon fiber, the azimuth angle of the cutting edge is also an important factor that affects the thrust force. A single carbon fiber may be modeled as a beam on an elastic foundation, and the prediction model of thrust force on the chisel edge is established based on the theory of bending fracture. The model can reflect the influence of the material properties, cutting tool geometry parameters (including the length of chisel edge, rake angle and blunt radius of cutting edge), drilling process parameters, and ultrasonic vibration parameters on the thrust force on the chisel edge and quantitatively explain the reduction of thrust force and improvement of drilling quality during the longitudinal ultrasonic vibration drilling. The prediction model of the thrust force presented in this work can make up for the shortages of qualitative interpretation. The law of periodic variation of the chisel edge thrust force with the azimuth angle helps in developing a deep understanding of the CFRP drilling process and the material removal mechanism. The basis is provided in order to reduce and avoid the exit delamination defects in drilling, and to reasonably and quantitatively determine the spindle speed, feed rate, and drill bit geometry parameters. The reliability of the prediction model is verified by a drilling test.

Burr constitution analysis in ultrasonic-assisted drilling of CFRP/nano-graphene via experimental and data-driven methodologies

Influence of Machining Condition and Nano-Graphene Incorporation on Drilling Load and Hole Quality in Both Conventional Drilling and Ultrasonic-Assisted Drilling of CFRP

A New Strategy of Carbon Fiber Reinforced Plastic Drilling Evaluation Using Thermal Measurement

Investigation on carbon fiber-reinforced polymer combined with graphene nanoparticles subjected to drilling operation using response surface methodology and non-dominated sorting genetic algorithm-II

Optimization of Drilling Parameters on Delamination and Burr Formation in Drilling of Neat CFRP and Hybrid CFRP Nano-Composites

Study on Burr Formation and Tool Wear in Drilling CFRP and Its Hybrid Composites

Analysis of Drilling-Induced Geometrical Damages in Basalt and Carbon Fibre-Reinforced Polymer (BFRP and CFRP) Composites

Carbon fiber reinforced polymer in drilling: From damage mechanisms to suppression

A study on the ultrasonic vibration on the cutting performance during ultrasonic-assisted drilling of CFRP with twist and dagger drill bits

Modeling Evolution of Cutting Force in Ultrasonically Assisted Drilling of Carbon Fiber Reinforced Plastics

Mechanics of thrust force on chisel edge in carbon fiber reinforced polymer (CFRP) drilling based on bending failure theory

A Comprehensive Study on the Optimization of Drilling Performance in Hybrid Nano-Composites and Neat CFRP Composites Using Statistical and Machine Learning Approaches

A Critical Review of the Drilling of CFRP Composites: Burr Formation, Characterisation and Challenges

An Investigation of Drilling High-Strength CFRP Composites Using Specialized Drills

Delamination assessment and prediction in ultrasonic-assisted drilling of laminated hybrid composites

A Study on Drilling High-Strength CFRP Laminates: Frictional Heat and Cutting Temperature

Simulation and experimental research on longitudinal-torsional ultrasonic vibration drilling of CFRP/Ti laminates

Drilling Performance of Uncoated Brad Spur Tools for High-Strength Carbon Fiber-Reinforced Polymer Laminates

A review on CFRP drilling: fundamental mechanisms, damage issues, and approaches toward high-quality drilling

Wear Behavior of Special Tools in the Drilling of CFRP Composite Laminates

A Drilling Case Study in Polymer Composites Reinforced by Virgin and Recycled Carbon Fibres (CFRP and Rcfrp) to Analyse Thrust Force and Torque