Abstract:Metal bipolar plates (BPPs) are crucial components of proton exchange membrane fuel cells (PEMFCs), with the quality of their formation affects the power generation efficiency and lifespan of the fuel cells. The predominant manufacturing method, stamping, often results in localized excessive stretching of metal BPPs, thereby limiting the depth of the flow channels. Roll forming, dominated by bending deformation, is a forming process that ensures uniform thinning and greater depth of BPPs. The multi-directional flow channel roll forming model for BPPs is constructed in this paper for the first time, the characteristics of the roll forming process is investigated. Effects of process parameters on the forming results are discussed. The investigation indicates that during the roll forming process, the channel ports and corners are critical areas where defects are most likely to occur. The average filling ratio of the longitudinal flow channels is 5.6% higher than that of the transverse flow channels. The plastic strain in the longitudinal flow channels is about 36% higher than in the transverse ones, which making the form is more difficult to form, but the thickness is more uniform. Increasing the diameter of the rollers can enhance the filling ratio and flatness, but it will exacerbate thinning at the corners of the flow channels. When the ratio of the flow channel width to the rib width is close to 1, the filling ratio of the BPP is higher, with less thinning, resulting in a better forming result. As the depth of the flow channel increases, resulting in a thinner BPP, when depth-to-width ratio exceeding 0.6 is more likely to lead to failure. Increasing the speed of roll forming can lead to a greater thinning of the BPP and may even cause it to crack. The thinner the sheet metal is, the higher the filling ratio of the BPP and the more uniform its thickness. Those results can provide technical references for the structural design and forming process optimization of BPPs.

Experimental Study on Superplastic Forming for Inconel 718 Alloy Bipolar Plate

Study on Springback Behavior in Hydroforming of Micro Channels for a Metal Bipolar Plate

Investigation on formability of bipolar plates during flexible micro forming of Cu/Ni clad foils

Study on Laser Beam Welding/superplastic Forming Technology of Multi-Sheet Cylinder Sandwich Structure for Inconel718 Superalloy with Ultra-Fine Grains

Insight into Elongation and Strength Enhancement of Heat-Treated LPBF Ni-based Superalloy 718 Using In-Situ SEM-EBSD

Study of Pre-Precipitated Δ Phase Promoting Deformation Twinning and Recrystallization Behavior of Inconel 718 Superalloy During Hot Compression

Laser powder bed fusion of micro-channels for the application of proton exchange membrane fuel cell bipolar plates

Plastic Deformation Forming of Metallic Bi-Polar Plate – Part 1: Theoretical Basis and Fundamental

Development of Prior Particle Boundary Free Hot-Isostatic-Pressing Process for Inconel 718 Powder

Thin Metallic Wave-Like Channel Bipolar Plates for Proton Exchange Membrane Fuel Cells: Deformation Behavior, Formability Analysis and Process Design

Tailored Nanocrystalline Microstructure of Niobium Precoatings with High Tensile Ductility for Formable Precoated Metallic Bipolar Plates

Microstructure Evolution of Inconel 718 Superalloy During Hot Working and Its Recent Development Tendency

Hot stamping of ultra-thin stainless steel sheets for bipolar plates

Research on microstructure and mechanical properties of hybrid plasma arc and micro-rolling additive manufacturing of Inconel 718 superalloy

Formation and effect of hierarchical structures on corrosion performance of stainless steel bipolar plate fabricated by powder bed fusion

Investigation of roll forming process and quality control factors for metal bipolar plates

Research on superplastic forming/diffusion bonding technology of Ti2AlNb alloy

Numerical Investigation of Formed Residual Stresses and the Thickness of Stainless Steel Bipolar Plate in PEMFC

Fabrication of Metallic Bipolar Plates for Proton Exchange Membrane Fuel Cell by Flexible Forming Process-Numerical Simulations and Experiments

Surface Morphology Refinement and Laves Phase Control of Plasma Arc Additively Manufactured Inconel 718 Via an Alternating Magnetic Field

Rubber-Assisted Vaporizing Foil Actuator Forming of SS304 Bipolar Plates: Processes and Effects