Abstract:The 15-MA driver is powered by 24 linear-transformer-driver (LTD) modules connected electrically in parallel. The magnetically-insulated-transmission-line (MITL) system of the 15-MA driver adopts a four-level design. It is expected that the primary source delivers a more than 15 MA current to a physics load. The typical one-dimensional steady-state pressure-balance model is adopted to calculate the electron flow current of the outer MITLs of the 15-MA driver after the magnetic insulation has been established. The cathode plasma expansion and the collisional flow electrons are considered on the basis of that model. Multiple designs with different characteristic parameters of the MITL system include the vacuum impedance of the constant-impedance segment of the outer-MITL, the minimum gap of the outer-MITL, and the location of the post-hole convolute (PHC). The flow currents of these designs are calculated in three typical times (1/3 peak load current time, peak load current time, and 5 ns before the Z-pinch stagnation) by establishing the equivalent circuit model of the 15-MA driver. The influences of these characteristic parameters on the electrical pulse transmission and convergence of the 15 MA driver are obtained. The calculation results show that the electron flow current at the end of MITL is greatly affected by the impedance of the end of MITL after the electron flow current has entered into the steady state magnetic insulation. The flow current decreases from 184.7 kA to 106.9 kA, while the load current is reduced by 0.5 MA, as the vacuum impedance increases from 0.42 Ω to 0.84 Ω. This is mainly because the central inductance increases by about 1.43 nH (from 9.94 nH to 11.37 nH). In the time of 5 ns before load stagnation, the flow current decreases from 181.9 kA to 85.1 kA as the minimum gap of the outer-MITL increases from 7.10 mm to 14.00 mm, and the peak load current drops only by about 0.1 MA. The flow current and load current decrease slowly as the location radius of the PHC decreases until the radius decreases to 7.65 mm. The research in this paper is helpful in guiding the structure optimization for the central converging region of future Z-pinch driver.

Improvement of vacuum maintenance capability and output pulse limit in a hard-tube MILO with a carbon fiber array cathode

A Novel ZVS High Voltage Power Supply for Micro-Channel Plate Photomultiplier Tubes

A High-Efficiency Ridged Magnetically Insulated Transmission Line Oscillator

Relation Analysis Between Cathode Ablation and Voltage for A Magnetically Insulated Transmission Line Oscillator

Design and simulation of double ladder cathode magnetically insulated transmission line oscillator

Experimental Study on the Current Transmission Efficiency for the Transition Structure of Vacuum Transmission Line MITL on Flash-II Accelerator

Pulse Loss Front in Coaxial Cylinder Vacuum Magnetically Insulated Transmission Lines under Different Voltages

A High-Efficiency Magnetically Insulated Transmission Line Oscillator

Cathode Design Optimization Toward The Wide-Pressure-Range Miniature Discharge Ion Source For A Vacuum Micropump

High Power Current Pulse Power Supply For Micro-Arc Oxidation

Preliminary Experimental Research on Ku-Band MILO

Modification of polymer velvet cathode via metallic Mo coating for enhancement of high-current electron emission performances

Improvements on the Stability and Operation of a Magnetron H- Ion Source

Simulation Investigation of High-Efficiency $L$ -Band MILO Using Reflector Stubs

A high current pulsed power generator CQ-3-MMAF with co-axial cable transmitting energy for material dynamics experiments

Preliminary study of dual annular multiple-beam cathode for V-band coaxial transit-time oscillator

An On-Chip Vacuum Triode Based on Thermionic Electron Emission from Super-Aligned Carbon Nanotube Films

Improvement of Electromagnetic Self-Locking Device for Cylinders in High Temperature Gas-Cooled Reactor

Analysis of Electron Flow Current in Vacuum Magnetically-Insulated-transmission-line Sheath for 15-MA Z-pinch Driver

Model of a 5-MA Linear-Transformer-Driver Accelerator: Comparison of MITL Performance for Bremsstrahlung Electron Beam Diodes and Z-Pinch Loads

Design of Pulsed Power Source for Micro-Arc Oxidation