Abstract:The introduction of polyhedral ZIF‐67 particles and ionic liquid electrolytes (ILE) to the PEO/LiTFSI‐based composite polymer electrolytes serves as important additives to enhance the properties of PEO polymer. Additionally, the optimization of the polymer electrolyte thickness significantly boosts the ionic conductivity, lithium‐ion transference number, and overall performance of ASSLMB batteries. Polyethylene oxide (PEO)/lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) is among the most promising candidates for developing solid polymer electrolytes (SPEs) for all‐solid‐state lithium‐metal batteries (ASSLMBs). However, practical applications of the PEO/LiTFSI system face challenges due to its relatively low ionic conductivity and low Li+ transference number. To address these issues, a method is proposed that incorporates multiple components, including zeolitic imidazolate frameworks (ZIF‐67) as fillers and ionic liquid electrolytes (ILEs) as plasticizers, into a PEO/LiTFSI matrix. By optimizing the fabrication process, ultra‐thin membranes of the integrated electrolyte PEO/LiTFSI‐ILE‐ZIF‐67 (PLiZ) with a thickness of 32 μm are developed, achieving high ionic conductivity (1.19 × 10−4 S cm−1 at 25 °C), broad electrochemical stability (5.66 V), and high lithium‐ion mobility (0.8). As a result, the fabricated ASSLMBs exhibited excellent cycle stability at both room temperature and 60 °C, delivering an initial specific discharge capacity of 166.4 mAh g−1 and an impressive capacity retention of 83.7% after 1000 cycles at 3C under 60 °C, corresponding to a low fading rate of 0.0163% per cycle. Additionally, the designed SPEs demonstrated high safety properties, as shown by the successful cutting and folding of a working LiFePO4/PLiZ/Li pouch cell. Therefore, this study presents a comprehensively improved method for developing high‐performance ASSLMBs.

Poly (ethylene oxide) based solid polymer electrolyte improved by multifunctional additives of poly (acrylamide) and LiI

Synergistic Combination of Crosslinked Polymer and Concentrated Ionic Liquid for Electrolytes with High Stability in Solid-State Lithium Metal Batteries

Highly Safe, Ultra‐Thin MOF‐Based Solid Polymer Electrolytes for Superior All‐Solid‐State Lithium‐Metal Battery Performance

Advanced High-Voltage Electrolyte Design Using Poly(ethylene oxide) and High-Concentration Ionic Liquids for All-Solid-State Lithium Metal Batteries

Polyaspartate Polyurea-Based Solid Polymer Electrolyte with High Ionic Conductivity for the All-Solid-State Lithium-Ion Battery

Polybenzimidazole-reinforced polyethylene oxide-based polymer-in-salt electrolytes enabling excellent structural stability and superior electrochemical performance for lithium metal batteries

Two-dimensional silica enhanced solid polymer electrolyte for lithium metal batteries

Thiol‐Branched Solid Polymer Electrolyte Featuring High Strength, Toughness, and Lithium Ionic Conductivity for Lithium‐Metal Batteries

Tailored PEO/PEG-PPG Polymer Electrolyte for Solid-State Lithium-Ion Battery

Polymer dispersed ionic liquid electrolytes with high ionic conductivity for ultrastable solid‐state lithium batteries

Solid Electrolyte Based on Waterborne Polyurethane and Poly(ethylene Oxide) Blend Polymer for All-Solid-state Lithium Ion Batteries

High-performance Solid Polymer Electrolytes for Lithium Ion Batteries Based on Sulfobetaine Zwitterion and Poly (ethylene Oxide) Modified Polysiloxane

Star-shaped polyethylene glycol methyl ether methacrylate-co-polyhedral oligomeric silsesquioxane modified poly(ethylene oxide)-based solid polymer electrolyte for lithium secondary battery

Mechanism of Bilayer Polymer-Based Electrolyte with Functional Molecules in Enhancing the Capacity and Cycling Stability of High-Voltage Lithium Batteries

Metal Organic Frameworks Enabled Multifunctional Poly(ethylene oxide)-Based Solid Polymer Electrolytes with High Lithium-Ion Conductivity and Excellent Stability

PEO kaolinite intercalation interface accelerates lithium-ion transfer for all-solid-state lithium metal batteries

Construction of Stable Li2O‐Rich Solid Electrolyte Interphase for Practical PEO‐Based Li‐Metal Batteries

Ionic solid-like conductor-assisted polymer electrolytes for solid-state lithium metal batteries

PEO-based electrolyte filled with UV-cured 3D cross-linked polymer network for lithium metal batteries

Multiple ionic conduction highways and good interfacial stability of ionic liquid-encapsulated cross-linked polymer electrolytes for lithium metal batteries

Poly(Ether-Ester)-Based Solid Polymer Electrolytes with High Li-Ion Transference Number for High Voltage All-Solid-State Lithium Metal Batteries