Abstract:The MAX phase has attracted much attention due to its unique properties combined with the merits of both metal and ceramic, including the low density, high electrical conductivity and good oxidation resistance, which makes it significant for possible applications in various high temperature or other environments. There is a lot of research work on Ti2AlX (X=C, N). However little research about thermodynamic properties at high pressure is carried out. So we study the structural, mechanical and thermodynamic properties of Ti2AlC and Ti2AlN at various pressures and temperatures. The first-principles calculations based on electronic density-functional theory framework are used to investigate the properties at various pressures. The cut-off energy is 350 eV. Converged results are achieved with 10102 special K-point meshes. The self-consistent convergence of total energy is set to be 5.010-6 eV/atom. According to the calculated structural parameters at various pressures, we can find that the ratios V/V0 (V0 denotes the system volume at 0 GPa) of Ti2AlX are reduced by 20.59% and 18.93%, respectively, so the compressibility of the system is strong. As the internal pressure increases, the curves of V/V0 become gentle. Then we calculate elastic constants at pressures ranging from 0 to 50 GPa in steps of 10 GPa. It is obvious that the Ti2AlX is mechanically stable because all of the elastic constants satisfy the Born stability criteria. The bulk modulus, shear modulus and Young's modulus linearly increase with internal pressure increasing, implying that the pressure can improve the resistance to volume deformation. The ductility and brittleness can be judged according to Pugh's criterion (ratio of bulk modulus to shear modulus B/G), and the brittle nature turns into ductile nature in a pressure range of 40-50 GPa for the Ti2AlX since the value of B/G exceeds 1.75. Finally, we study the thermodynamic properties at various pressures and temperatures based on the quasi-harmonic Debye approximation theory, including the bulk modulus, heat capacity and thermal expansion coefficient. The bulk modulus decreases with temperature increasing but increases with pressure increasing. The heat capacity at constant volume Cv and the heat capacity at constant pressure Cp have the same variation tendency, while Cv obeys the Dulong-Petit limit. It is easy to see that temperature and pressure have opposite influences on heat capacity and the effect of temperature is more significant than that of pressure. The effects of temperature and pressure on linear expansion coefficient mainly occur at low temperature and the effect of pressure is not so considerable when the pressure exceeds 30 GPa. Above all, the effects of temperature and pressure on thermodynamic properties are inverse.

Thermoelastic Properties Of The Ti2AlC MAX Phase: An Ab Initio Study

Theoretical Investigation of the High Pressure Structure, Lattice Dynamics, Phase Transition, and Thermal Equation of State of Titanium Metal

Structural, Mechanical, and Thermodynamic Properties of Ti2AlX (X = C, N) at High Pressure

Ab Initio Studies On Phase Transition, Thermoelastic, Superconducting And Thermodynamic Properties Of The Compressed Cubic Phase Of Alh3

First-principles Investigation of the Structural, Mechanical and Thermodynamic Properties of Al2Cu Phase under Various Pressure and Temperature Conditions

On the determination of the thermal shock parameter of MAX phases: A combined experimental-computational study

New MAX Phase Compound Mo2TiAlC2: First-principles Study

On the stochastic phase stability of Ti2AlC-Cr2AlC

Insights into the Mechanical Properties and Thermal Transport of Ti3(Al1-xAx)C2 Solid Solutions: A Comprehensive Theoretical Study Combined with Experiment

Maximizing the mechanical performance of Ti3AlC2-based MAX phases with aid of machine learning

Pressure‐induced phase transition and elastic properties of TiO2 polymorphs

Exploring the Electronic, Mechanical, Anisotropic and Optical Properties of the Sc-Al-C MAX Phases from a First Principles Calculations

Pressure-induced phase transition and elastic properties of TiO<sub>2</sub>polymorphs

Screen the elastic and thermodynamic properties of MAX solid solution using DFT procedue: Case study on (Ti1-xVx)2AlC

Statistical analysis of the strength reliability of the MAX phases

Assessing the Neutron-Irradiation Resistance of Ti-Based MAX Phases at High Temperatures

The Pressure Dependence of Physical Properties of (w2/3ti1/3)3alc2 and Its Counterpart W3AlC2 by First-Principles Calculations

Pressure effect on the physical properties of 413-type MAX phase compound Nb4AlC3: Insights from DFT simulation

Mechanical Characterisation of the Protective Al$_2$O$_3$ Scale in Cr$_2$AlC MAX phases

The Rendering from the Periodic System of Elements on the Stability, Elastic, and Electronic Properties of M2AC Phases

First-principles calculations of the elastic anisotropy, thermal conductivity, and optical properties of MAX-phase M 2 AlC (M = V, Nb, Ta) series carbides