Abstract:Prime-Cam, one of the primary instruments for the Fred Young Submillimeter Telescope (FYST) developed by the CCAT Collaboration, will house up to seven instrument modules, with the first operating at 280 GHz. Each module will include three arrays of superconducting microwave kinetic inductance detectors (KIDs). The first KID array fabricated for the 280 GHz module uses titanium-nitride (TiN) as the superconducting material and has 3,456 individual detectors, while the other two arrays use aluminum. This paper presents the design and laboratory characterization of the 280 GHz TiN array, which is cooled below its critical temperature to ~0.1 K and read out over six RF feedlines. LED mapping, a technique for matching the measured resonant frequency of a detector to its physical position, was performed on the array so that the results can be used to lithographically trim the KID capacitors and increase the yield of the array by reducing frequency collisions. We present the methods and results of LED mapping the 280 GHz TiN KID array before deployment on FYST.

What problem does this paper attempt to address?

The problem that this paper attempts to solve is: how to determine the physical position of each detector in a 280 - GHz titanium nitride (TiN) superconducting microwave kinetic - inductance detector (KID) array through LED mapping technology, in order to reduce frequency collisions and improve the yield of the array. Specifically, the research aims to: 1. **Design and Laboratory Characterization**: Design and perform laboratory characterization on the 280 - GHz TiN KID array for the Fred Young Sub - millimeter Telescope (FYST). 2. **Application of LED Mapping Technology**: Match the measured resonant frequencies with the physical positions of the detectors through LED mapping technology, so that the KID capacitors can be trimmed by lithography technology later, thereby reducing frequency collisions and improving the yield of the array. 3. **Improve Array Performance**: By reducing frequency collisions, improve the overall performance and reliability of the KID array to ensure its efficient operation in practical applications. ### Specific Problems and Solutions - **Problem**: In a large - scale KID array, how to accurately match the resonant frequency of each detector with its physical position? - **Solution**: Use LED mapping technology. By activating LEDs at different positions and recording the corresponding time - series data, the physical position of each detector can be determined. - **Problem**: How to reduce frequency collisions and improve the yield of the KID array? - **Solution**: Based on the LED mapping results, trim the KID capacitors by lithography technology, adjust the resonant frequencies, and reduce frequency overlaps. ### Research Background This research is part of the Prime - Cam instrument developed for the CCAT collaboration project. Prime - Cam will be installed on FYST to observe a wide - band from 280 GHz to 850 GHz and perform imaging spectroscopic measurements. The 280 - GHz module is the first deployed module, which contains three KID arrays. One of them uses TiN as the superconducting material, and the other two use aluminum (Al). The TiN array is one of the earliest fabricated arrays, with a total of 3,456 independent detectors, divided into six RF feed - line readouts. ### Experimental Methods 1. **Design and Assembly**: Design a TiN KID array with 3,456 independent detectors and install it on a gold - plated aluminum substrate, coupled to an aluminum feed - source array. 2. **Cooling and Readout**: Cool the array to approximately 100 mK and use a ROACH - 2 board for readout. 3. **LED Mapping**: Use a custom - made LED mapping board. By activating LEDs at different positions and recording time - series data, determine the physical position of each detector. 4. **Data Analysis**: Combine S21 scans and the time stamps of LED activation, match the time - series peaks with the corresponding LED positions, and finally determine the detector's physical position. ### Results By performing LED mapping on the 280 - GHz TiN KID array, 3,282 resonator positions were successfully mapped, accounting for approximately 95% of the total number of detectors. The results show that the detector yields of each feed - line are between 93% and 96%, and the difference between the measured resonant frequencies and the designed values is approximately 20%. In addition, some positions where no resonators were found due to manufacturing defects were also discovered. ### Follow - up Work Based on the LED mapping results, lithography capacitor trimming will be carried out at NIST to further reduce frequency collisions and improve the array yield. In the future, the 280 - GHz instrument module will continue to be tested, preparing for the first deployment in early 2026. ### Summary This research has successfully solved the problem of matching the physical position of detectors with the resonant frequency in large - scale KID arrays through LED mapping technology, and provided an effective method for improving the array yield. This marks an important progress in maximizing the yield of KID arrays.

CCAT: LED Mapping and Characterization of the 280 GHz TiN KID Array

CCAT: Comparisons of 280 GHz TiN and Al Kinetic Inductance Detector Arrays

CCAT: Nonlinear effects in 280 GHz aluminum kinetic inductance detectors

CCAT: Detector Noise Limited Performance of the RFSoC-based Readout Electronics for mm/sub-mm/far-IR KIDs

CCAT: Prime-Cam Optics Overview and Status Update

Design and testing of Kinetic Inductance Detector package for the Terahertz Intensity Mapper

Design of The Kinetic Inductance Detector Based Focal Plane Assembly for The Terahertz Intensity Mapper

High-sensitivity Kinetic Inductance Detector Arrays for the Probe Far-Infrared Mission for Astrophysics

Development of an MKID frequency-to-pixel LED mapper for SPT-3G+

Design of Large Low Noise Transition Edge Sensor Arrays for Future FIR Space Missions

Characterization of high aspect ratio TiAu TES X-ray microcalorimeters array using the X-IFU Frequency Domain Multiplexing readout

A ThermalKinetic Inductance Detectors Pixel Design for Cosmic Microwave Background Observations at 90/150 GHz bands

Single Pixel Performance of the Kinetic Inductance Detectors for the Terahertz Intensity Mapper

Characterization of Transition Edge Sensors for the Simons Observatory

CCAT-prime Collaboration: Science Goals and Forecasts with Prime-Cam on the Fred Young Submillimeter Telescope

The Tianlai Cylinder Pathfinder Array: System Functions and Basic Performance Analysis

Hierarchical phased-array antennas coupled to Al KIDs: a scalable architecture for multi-band mm/submm focal planes

The Simons Observatory: Large-Scale Characterization of 90/150 GHz TES Detector Modules

Frequency domain multiplexing readout for large arrays of transition-edge sensors

Hierarchical Phased-Array Antennas Coupled to Al KIDs: A Scalable Architecture for Multi-band Millimeter/Submillimeter Focal Planes