Abstract:It is well known that the prior austenite grain (PAG) microstructure of steels has a significant impact on their microstructure evolution and mechanical properties. Many PAG measuring techniques have been developed over many decades, with the effectiveness of each varying alloy-to-alloy. Some of the more common techniques, specifically for bainitic and martensitic grades, are thermal etching and picric acid etching, which both involve the preferential etching of PAG boundaries in order to reveal the austenitic microstructure. More recently, parent grain reconstruction techniques using EBSD (electron backscatter diffraction) mapping have shown good promise in recreating PAG microstructures from BCC-FCC orientation relationships, and can now be deployed at speed with the advent of rapid detectors (1000s of pixels per second). This study aims to compare the accuracy and relative advantages/disadvantages of picric acid etching, thermal etching and EBSD reconstruction methods. A TESCAN and NewTec In-Situ Testing (TANIST) capability was used to directly observe and measure the true high-temperature PAG structure during the austenitisation of SA-540 B24 low alloy steel. These high-temperature PAG measurements were then compared to measurements from the same area obtained using thermal etching, picric acid etching and EBSD parent grain reconstructions after quenching to room temperature. Reconstructing the parent austenite grains from EBSD data resulted in the closest measurement of PAG size. PAG boundaries were delineated well by thermal etching but surface effects (such as surface relief and ghost traces) created complexities when identifying the exact position of boundaries. Picric acid etching, which produced the least accurate measurement, was found to reveal PAG boundaries well, however it was limited by its ability to sufficiently etch annealing twin boundaries and its susceptibility to microsegregational effects. EBSD reconstruction and thermal etching were more consistent at reconstructing/revealing these boundaries, although inaccuracies with the techniques were still observed.

Improving parent-austenite twinned grain reconstruction using electron backscatter diffraction in low carbon austenite

Effective structural unit analysis in hexagonal close packed alloys -- reconstruction of parent beta microstructures & crystal orientation post processing analysis

Prior austenite grain measurement: A direct comparison of EBSD reconstruction, thermal etching and chemical etching

Registration between DCT and EBSD datasets for multiphase microstructures

Texture Analysis of Hot Rolled Martensitic and Bainitic Steels by Electron Backscatter Diffraction to Quantify Parent Austenite States

Advanced microstructural characterization in high-strength steels via machine learning-enhanced high-speed nanoindentation and EBSD mapping

Control of Upstream Austenite Grain Coarsening during the Thin-Slab Cast Direct-Rolling (TSCDR) Process

Grain boundary engineering of AL6XN super-austenitic stainless steel: Distinctive effects of planar-slip dislocations and deformation twins

In situ measurement of austenite grain growth and recrystallization using laser ultrasonics

Parent grain reconstruction from partially or fully transformed microstructures in MTEX

SEM-WDS x STEM-EDS: Improving how we measure Mn partitioning in retained austenite in medium-Mn TRIP steels

High-resolution reconstruction-based investigation of multi-scale lamellar microstructures by coupled crystal plasticity and in-situ experiment

Grain-level effects on in-situ deformation-induced phase transformations in a complex-phase steel using 3DXRD and EBSD

EBSD investigation for influences of austenitization time and cooling rate on microstructure in a ultrahigh carbon steel

Using transmission Kikuchi diffraction to characterise α variants in an α + β titanium alloy

Influence of Thermomechanical Control Process on the Evolution of Austenite Grain Size in a Low-Carbon Nb-Ti-Bearing Bainitic Steel

In-Situ Neutron Diffraction and Crystal Plasticity Finite Element Modeling to study the Kinematic Stability of Retained Austenite in Bearing Steels

Atom-probe tomographic and dilatometric studies of phase-transformations after inter-critical annealing of a low-carbon dual-phase steel

Thermo-kinetic Design of Retained Austenite in Advanced High Strength Steels

Strain partitioning characterization of advanced high strength steels using in-situ tensile tests with Micro digital image correlation – Methodology and analysis

New observations of the twinning effect and austenite stability in intercritical quenched and tempered steel with high strength