Abstract:316 Objectives: The performance of conventional SPECT system suffers a fundamental limitation that the mechanical collimation forces a compromise between detection efficiency and spatial resolution. We propose and evaluate a novel concept, namely self-collimating, that uses spatially separated scintillation detectors (SSSD) for photon collimation to reach a new level of high spatial resolution and high detection efficiency. Methods: In a system that consists of multiple layers of SSSD, the SSSD on one layer plays both the function of collimation - allowing photons passing through the detector separations to reach SSSDs on the outer layers - and the function of detection. Only the innermost SSSD uses a conventional high efficiency collimator. There is no gap in between the detectors in the outermost layer. We evaluate two highly correlated self-collimating SPECT designs, one through Monte-Carlo simulation and one through prototype experiments. In the Monte Carlo simulation, we simulate a full-ring self-collimating SPECT with 4 layers. The ring diameters corresponding to the four layers are 180, 220, 260 and 300 mm. Each layer is composed of 570 x 11, 690 x 11, 810 x 11, and 1890 x 11 0.5 mm (tangential) x 21 mm (axial) x 6 mm (radial) GAGG scintillators with 6 mm axial gap. In the middle three SSSD layers, the adjacent scintillators have a 0.5 mm gap in between in the tangential direction. We assume that the intrinsic resolution in the axial direction is 1.5 mm. The conventional collimator is a 40-mm-diameter tungsten cylinder with 105 (tangential) x 11 mm (axial) 0.4-mm-diameter pinholes spaced 1.2 mm (tangential) and 6 mm (axial) center-to-center evenly on the cylinder, all pinholes focus at the center of FOV. The experimental prototype is partial ring that consists of a 2.5-mm thick tungsten slab with multiple 1-mm slits spaced 3 mm center-to-center and 3 layers. Each layer consists of 7 detector modules, each module consists of two 24 × 12 scintillator arrays. The scintillators on the inner and middle layer SSSDs are 1.35 mm x 2.7 mm x 4 mm YSO and LYSO crystals, on the outer layer are 1.35 mm x 2.7 mm x 7 mm GAGG and LYSO crystals, all interleaved in tangential and axial directions. Each detector module has one end-side optically coupled to an 8 × 8 SiPM array. System performance was evaluated with hot rod phantom, disc phantom and contrast phantom in the simulated system. Spatial resolution was measured experimentally with three 3x3 Tc99m point source phantoms at 0.3 mm, 0.4 mm and 0.6 mm. OS-EM algorithm was used to reconstruct the image. Results: In the simulated system, the peak and average detection efficiency in a 10 mm x 10 mm FOV is 1.37% and 0.46%, respectively. A 2D hot rod phantom study shows that the best achievable image resolution is 0.05 mm transaxially and 0.2 mm axially in nearly noise-free condition. With a 3D hot rod phantom that consists of 15 0.1 mm hot rods, we demonstrate that with 1 μCi Tc99m total activity and 10 min scan time, all the rods are clearly separable in the reconstructed image. The contrast phantom studies show that with a total activity of 0.2 mCi in a 8 mm (φ) x 3 mm(L) warm cylinder with 6 hot rods at 8:1 contrast, the smallest visible hot rod is 0.15 mm with a 20 min scan. With the prototype system, the point sources with a 0.3 mm spacing can be distinguished. Conclusions: The simulations show astonishingly outstanding imaging performance. The spatial resolution demonstrated in the experiment is slightly better than the best reported value to our knowledge. We conclude that the self-collimating concept opens a door to develop a new generation of SPECT systems and indicates a potential paradigm shift in emission tomography. The research was supported by the National Natural Science Foundation of China (No. 81727807, No.11575096, No. 11605008) and National Key Research and Development (R&D) Plan of China (Grant ID. 2019YFF0302503 and 2016YFC0105405).

Collimator-less SPECT System Design for Dynamic Whole-body Imaging

Design and Simulations of a Self-Collimating Whole-Body SPECT System

Design and Performance Evaluation of a Self-Collimating SPECT System for Small Animal Imaging

A Monte Carlo study for optimizing the detector of SPECT imaging using a XCAT human phantom

Development and Performance Evaluation of an Ultra-High-Resolution Self-Collimation SPECT System for Small Animal Imaging

Theory and realization of a 2D high resolution and high sensitivity SPECT system with an angle-encoding attenuator pattern.

High-sensitivity cardiac SPECT system design with collimator-less interspaced mosaic-patterned scintillators

An energy-optimized collimator design for a CZT-based SPECT camera

A projection-domain low-count quantitative SPECT method for alpha-particle emitting radiopharmaceutical therapy

Half-millimeter animal SPECT imaging on a clinical SPECT scanner with highly flexible collimator design

In vivo quantitative SPECT imaging of actinium-226: feasibility and proof-of-concept

Feasibility Studies of Animal SPECT Imaging with a Stationary Multi-Pinhole Collimator Inserted to Animal PET Detector Ring

Performance evaluation of A-SPECT: a high resolution desktop pinhole SPECT system for imaging small animals

Dedicated small field of view SPECT system based on a 5" PSPMT and crystal scintillator array for high resolution small animal cardiac imaging

Evaluation of a variable-aperture full-ring SPECT system using large-area pixelated CZT modules: A simulation study for brain SPECT applications

Conceptual design of a large pixelated CZT detector with four-hole collimator matched pixel detector for SPECT imaging: a Monte Carlo simulation study

Third Generation Gamma Camera SPECT System

Slit slat collimator optimization with respect to MTF

Quantitative SPECT/CT imaging of actinium-225 for targeted alpha therapy of glioblastomas

Low-Cost High-Resolution Animal Spect Imaging on A Clinical Spect Scanner

Feasibility of internal-source tracking with C-arm CT/SPECT imaging with limited-angle projection data for online in vivo dose verification in brachytherapy: A Monte Carlo simulation study