Abstract:This article shows that the governing equations of any plate theory can be directly obtained by manipulating the three-dimensional (3D) equilibrium indefinite equations. Stress components are transformed into plate stress resultants by implementing a few steps proposed in this article. Such a manipulation is shown for simple and complex deformation states. Various known plate theories are considered, such as membrane and bending ones. The most general equations are obtained by referring to higher-order theories based on the Carrera Unified Formulation. To show the method's effectiveness, the differential equations of known (Reissner–Mindlin, Hildelbrand–Reissner–Thomas) and unprecedented plate theories are derived by simply working on the 3D-equilibrium equations. The introduced manipulation consists of the following steps: Equation (1) (1) −σij,i=Pj,i,j=x,y,z (1) The 3D equilibrium elasticity is formally written for each of the degrees of freedom of the considered plate theories; Equation (2) (2) −Nxx,x=qx,−Nyy,y=qy. (2) the stress resultants are used to replace stress components in the latter equations; Equation (3) (3) ux(x,y,z)=ux0(x,y)+z ux1(x,y)+ezux2(x,y)uy(x,y,z)=uy0(x,y)+z uy1(x,y)+z3uy2(x,y)uz(x,y,z)=uz0(x,y)+z uz1(x,y)+z cos (2zh) uz2(x,y). (3) the derivatives of the stress components along the plate reference surface coordinate x , y do not affect the nature of the indefinite equilibrium equations, and these derivatives are directly moved to the related stress resultants; Equation (4) (4) δu:−Tx,x−Ty,y−Tz,z=P (4) the derivatives over the thickness coordinate z should: (i) change the sign of the related stress resultants and (ii) be applied to the base functions of z used to define the stress resultants (as well as the assumption for the displacement along the thickness). In conclusion, this article presents a straightforward method that can effectively replace the use of Newton and Lagrange methods to derive the equilibrium equations of any plate theory. The four steps introduced in this article demonstrate the simplicity and efficiency of this approach.

On the derivation of the equilibrium equations in terms of displacement

Physical Derivation of Effective Stress from Balance Law and Experimental Evidence

Derivation of Elastic Wave Equation from New Motion Description

A Necessary and Sufficient Boundary Integral Formulation for Plane Elasticity Problems

Demonstrating Invalidity of Solution Methods Involved in Solving Compatibility Equations

The Completeness and a New Derivation of the Stroh Formalism of Anisotropic Linear Elasticity

Stability of Displacement to the Second Fundamental Problem in Plane Elasticity

A Simple Derivation of the Birch–Murnaghan Equations of State (EOSs) and Comparison with EOSs Derived from Other Definitions of Finite Strain

The Second Eshelby Problem and Its Solvability

Governing equations of plate theories by direct manipulation of three-dimensional elasticity equilibrium

From a distance: Shuttleworth revisited

On advantages of derivation of exact dynamical stiffness matrices from boundary integral equations

Correction of local-linear elasticity for nonlocal residuals: Application to Euler-Bernoulli beams

On equilibrium states of fluid membranes

On the incremental equations in surface elasticity

On the Derivation of Closed‐Form Expressions for Displacements, Strains, and Stresses Inside Poroelastic Reservoirs

Antiplane Shear Deformations of an Anisotropic Elliptical Inhomogeneity with Imperfect or Viscous Interface

Interface Mismatch Eigenstrain of Non-Slipping Contacts Between Dissimilar Elastic Solids

A Traction-Based Equilibrium Finite Element Free From Spurious Kinematic Modes For Linear Elasticity Problems

A Damped Dynamic Finite Difference Approach for Modeling Static Stress–Strain Fields

On Deformations of A Spherically Isotropic Hollow Sphere of A Functionally Graded Material